Search results for: 'AUTOMATIC DOOR'
- Related search terms
- door series 30 push bar panic exit dor parts 1311
- door series 30 push bar panic exit dog parts 1308
- door series push bar panic exit dor cal parts 1308
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit dent parts 1306
- door series 30 pull bar panic exit detex parts 1306
- door series 30 push bar panic exit drop parts 1307
- door series 30 pull bar panic exit deep parts 1308
- door o matic 1 panic device 1309
- dooramatic door series 30 push bar panic exit devic parts 1315
-
5" Kickdown Door Stop FS452 | Ives FS452 Kick Down Door Holder
5" Kickdown Door Holder FS452
The H.B. Ives FS452 is another classic kick down door stop. It features a simple hold and release, activated with a touch of the foot, and is constructed of cast bronze or brass depending on the finish you are ordering. A simple stainless steel spring clip holds the stop in the up position. The non-marring rubber shoe is replaceable, and they have a corrugated bottom to prevent sliding on the floor and a secure grip. This stop is shipped with matching finish sheet metal screws. The 5" model is for door to floor clearances of 3" or less. The hole spacing is 19/32" by 1-47/64".
Ives Part # FS452
GJ452-5- -
Kickdown Door Holder Rubber Shoe For GJ1154M and GJL444-555
Rubber Shoe For GJ1154M and GJL444-555 Kickdown Door Stop / Holder
Replacement rubber shoe
5/8" insert diameter
1" base diameter
8-32 threaded screwGJ1154 -
Floor Door Stop FS434
The Floor Door Stop FS434 is another one the old Ives parts that has been around for about 40 plus years. The FS434 is constructed of burnished wrought steel, with a soft, resilient gray rubber shoe. The shoe is replaceable and is under related products. The stop measures 2-5/8" overall height, and the base measures 1-1/2" wide by 2-3/4" long. This door stop ships with all the fasteners and anchors needed.
GJ434 -
Wall Door Stop WS11X
The WS11X door stop used to be under the Glynn-Johnson product line as the WB11X until they merged with H.B. Ives. At that point they became the WS11X. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11, except that it is designed for a masonry type mounting and ships with an expansion sheild.
GJWB12- -
Door Silencer For Metal Frames
For use on metal frames featuring
pneumatic design that, once installed,
forms an air pocket to absorb sound and
reduce noise of door closing.Diameter: 1/2"
Thickness: 1/8"
GJ64 -
Wall Door Stop / Bumper Convex WS407-CVX
The Ives Wall Bumper Stop WS407-CVX our economically price convex wall bumper. The metal ring is a wrought stainless steel, otherwise known as stamping. It features a concealed tamper-proof mounting, and is shipped pre-assembled to the back plate is reduce installation time. Installation is easy, just insert the screw driver through the pin hole in the rubber and tighten. The bumper is 2-1/2" in diameter and projects out 1".
GJ50W- -
Wall Door Stop WS11
The WS11 door stop used to be under the Glynn-Johnson product line as the WB11 until they merged with H.B. Ives. At that point they became the WS11. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11x, except that it is designed for wood or drywall mounting and ships with wood screws and anchors.
GJWB11- -
Ives 7212 Pivot Set
• Handed
• Top, header mount
• Bottom, jamb mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking7212 -
Wall Door Stop / Bumper Concave WS407-CCV
The Ives Wall Bumper Stop WS407-CCV our economically price concave wall bumper. The metal ring is a wrought stainless steel, otherwise known as stamping. It features a concealed tamper-proof mounting, and is shipped pre-assembled to the back plate is reduce installation time. Installation is easy, just insert the screw driver through the pin hole in the rubber and tighten. The bumper is 2-1/2" in diameter and projects out 1".
GJ60W- -
Ives 7222 Pivot Set
• Handed
• Top, header mount
• Bottom, base plate mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking7222 -
Ives LG1 Lock Guard
The Lock Guard with Security Pin is ideal to cover the latchbolt area of the door, lock and frame, with the added protection of a security pin to prevent separation of the door and door frame. The plate is through bolted with carriage bolts and nuts, which are included with the guard. The plate is constructed of 13 gauge stainless steel. The plate measures 3" wide and 11-1/2" high, with a center to center on the mounting bolts of 10-1/2".
Ives Part Number LG1-US32D
LG1- -
Continuous Full Mortise Hinge
The Ives 112HD Continuous Full Mortise Hinge Geared Hinge measures 83" long and is constructed of extruded aluminum. This hinge is non handed, and will work on doors up to 48" wide and 450 pounds. You can easily cut this hinge in the field if your door is less than 83" high.
GFM100- -
Ives Roller Bumper Straight Arm 6" RB472
The Ives Roller Bumper Straight Arm 6" RB472 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 6" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB6 or GJRB6.
GJRB6- -
Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3- -
Continuous Full Surface Geared Hinge
The Ives 157XY Continuous Full Surface Geared Hinge is an ideal solution for the replacement or worn or broken storefront door pivots, which we run across quite often. I our opinion this is the best solution if you can not find a compatable replacement pivot. The geared hinge will not allow the door to twist, which makes your door more sturdy in the frame. This hinge measures 83" long and is 3-7/16" wide included the cover which hides the screw mounting. A patented easy to install, heavy duty hinge which offers lateral and vertical adjustablility whle the door is still hanging. The hinge is non handed, will mount on a narrow frame, can be cut down in the field and will work on doors up to 550 pounds. 12-24 x 1/2" steel self drilling and tapping screws are included.GFS102- -
Roller Bumper Straight Arm 4" RB471
The Ives Roller Bumper Straight Arm 4" RB471 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 4-1/2" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB4 or GJRB4.
GJRB4- -
Lock Guard Standard Line
• Ideally suited for use with rose or escutcheon 2-3/4" wide or less.
• For use with Type 86 Mortise and Type 161 Cylindrical Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.2-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2"1625- -
Lock Guard Narrow Line
• Narrow design unit for use on rose or escutcheon 3-1/2" or less.
• For use with Type 86 Mortise and Type 161 Cylinder Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the opening
between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel1-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2”1625NL- -
Lock Guard Slim Line
• Designed for use on all Type 161 Cylindrical Locks (ANSI 156.2 Series 2000)
Monolock and Unilock.
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.1-1/2" Wide x 7" High
Stud center to center: 4-1/2"1625SL-