33 Series
RBA Door offers a large selection of Von Duprin 33 and 3327 panic device replacement parts. Call the experts that have been in business since 1970 for more information and assistance in finding the panic door hardware you require. Check out the Von Duprin 33A Rim Device Parts Break Down, Von Duprin 3327A Surface Vertical Rod Device Parts Break Down, the Von Duprin 3347A Concealed Rod Parts Break Down and 360-370 Outside Trim as well.
-
Von Duprin 33A Panic Device Only
Von Duprin 33A Exit Device Only
33A and 35A for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 35A has a smooth mechanism case and the 33A has grooved case. 33A/35A fits door stiles as narrow as 1 3/4". Newly designed device has a one piece center case cover.
33AEO -
Von Duprin 3327A Panic Device Only
Von Duprin 3327A Exit Device Only
3327A and 3527A for all types of single and double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 3527A has a smooth mechanism case and the 3327A has grooved case. 3327A/3527A fits door stiles as narrow as 1-3/4". Newly designed device has a one piece center case cover.
3327AEO -
Von Duprin 386NL Dummy Trim
Von Duprin 386NL Dummy Trim
This Von Duprin 386NL Night Latch Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Duprin 33A on the inside so they are on cohesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386NL Night Latch Trim is handed. Uses a standard Rim Cylinder.
386NL -
Von Duprin 386DT Dummy Trim
Von Duprin 386DT Dummy Trim
This Von Duprin 386DT Dummy Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Duprin 33A on the inside so they are on cohesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386DT Dummy Trim is non handed.
386DT -
Von Duprin 2227/3327A/9927 Top Latch 050400
Von Duprin 22, 33, and 9927 Top latch
This latch is used on the 2227, 3327A, and 9927 Surface Vertical Rod Devices. This latch is for use on devices shipped after October 1998. This is usually the problem if your bottom rod is dragging on the floor. Includes screws.
Von Duprin Part # 050400
G050400 -
Von Duprin 2227/3327/9927 Bottom Latch 050401
Von Duprin 22, 33, 9927 Bottom latch.
Used to replace the bottom latch on the Von Duprin 2227, 3327A, and 9927 on devices shipped after October 1998.
Includes screws and sometimes the bracket
Von Duprin Part # 050401
G050401 -
Von Duprin 99 Mechanism End Cap 050014
The Von Duprin 99 Mechanism End Cap 050014, also known as 33A/35A/98/99/330/350 Impact Resistant End Cap Kit. Replaces all of the old versions of the 98/99 End Caps, the mounting holes may be different. Includes end cap, bracket and all screws
Von Duprin Part # 050014
G99R10- -
Von Duprin 99 Cover Plate 050114
The Von Duprin 99 Cover Plate 050114 is for use on the 33A, 35A, 98 and 99 devices. Covers the dogging assembly on the hinge side of the door. The usually fall off when the End Cap is not on the exit device. Von Duprin is only shipping a 20-1/2" cover plate now, which will work on 3' and 4' doors, you will have to cut more off if you have a 3' device with a hack saw or chop saw.
Von Duprin Part # 050114 and 050117 Hex Key Dog Conversion Kit
Von Duprin 99 Cover Plate 050114
G99R50 -
Von Duprin ALK Alarm Kit
The Von Duprin ALK Alarm Kit converts the Von Duprin 22, 33A, 35A, 98 and 99 Devices to an alarmed exit device. When you exit the 85 decibel alarm will sound. Powered by a standard 9 volt battery and is controlled by a Mortise Cylinder with a straight cam. When battery is low, the alarm will beep.
Mortise Cylinder NOT included.
Von Duprin Part # 22-ALK, 33A-ALK, 35A-ALK, 98-ALK AND 99-ALK
ALK -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Von Duprin Dogging Hook 090044
The Von Duprin Dogging Hook 090044 is the piece that grabs the push bar mechanism and keeps it in the dogged position. The does wear out, but it takes a long time. This piece is used on the 22, 33A, 35A, 98 and 99 series devices made after 1997. We sell this part individually and it is #5 on the diagram.
G090044 -
Von Duprin 050709 Old Style Dogging Assembly
The Von Duprin 050709 Dogging Assembly is used to update the Von Duprin 22, 33, 35, 98 and 99 device shipped before 1997. The dogging key on this assembly is 5/32", and you would want to use the longer version of our 88R60 dog key.
Von Duprin Part # 050709
Old Part # 050153G050709 -
Von Duprin 050534 EL Potted Circuit Breaker
The Von Duprin 050534 EL Potted Circuit Breaker measures 5" long by 1-1/4" wide and 7/16" thick including the wires. This piece spikes the current to the solenoid to open the door, then lowers the current to keep the device open. The 050534 has a plug for the two wire input, and a plug for the 3 wire output. This Potted Circuit Breaker is also used on the Doromatic/Falcon Exit Devices, EL1490, EL1590, EL1690, EL1790, and EL2390. We sometimes find the number 101031-00 and 2148 on a sticker.
Old Von Duprin Part # 110741
Von Duprin Part # 050534
Doromatic/Falcon Part # 050534-00G050534
