Von Duprin
For the past 45 years Robert Brooke and Associates has been a leader in Von Duprin Exit Devices, either complete or repair hardware. Whether you have the economical 22 Series or the higher end 98/99 Series we have the hardware you need. Call and speak with product experts!
-
Von Duprin Panic Hardware 210K Knob Trim
The Von Duprin Panic Device 210K Knob Trim is for use on the 22 Rim and 2227 Surface Vertical Rod devices. Key in knob can lock and unlock the knob. Since the enforcement of local ADA standards, this knob is probably at the end of this life, no one seems to want these anymore. The mounting plate measures 3" wide by 4-25/32", and is 3-32" thick. We do have parts on this Knob, but at this point they are not on the website.
220K- -
Von Duprin Panic Device 210NL Trim
The Von Duprin Panic Device 210NL Trim is part of there economy series trims. This trim iis a pull with a key cylinder hole, it will line up with the chassis mounting holes of the 22 and 2227 devices. The key locks and unlocks the exit device. The plate measures 5-3/8" x 4-25/32" x 3/32", with a projection of 1-31/32".
220NL -
Von Duprin 2670 Guard-X Panic Device
Heavy Duty Design
The new Series 2670 Exit Alarm Lock provides secure protection through a large stainless steel deadbolt, which is 2" x 1/2" (51mm x 13mm) and has over a 3/4" (19mm) throw. The engagement area into the strike is over 1 1/4" (32mm) square inches. The cast aluminum latch case protects the internal mechanism and resists tampering or vandalism from inside the door. This unit has been tested to withstand up to 1600 pounds of static load force against the door.Fits 36" to 48" doors.
Uses 9 volt battery
Ships with all mounting hardware and strike.2670EO- -
Von Duprin 88 Panic Device
The Von Duprin 88 Panic Device has been around since the 1950's, and is probably the device that put Von Duprin on the Map. It is designed for all types of single and double doors with mullions. It is field reversible, and ships with a 42" cross bar that can be cut down in the field. The device is dogged down with a 5/32" hex key, and ships with all mounting screws and the 299 strike.
88EO- -
Von Duprin Panic Device 880TP Trim
The Von Duprin Panic Device 880TP Trim is for the 88 series only. The stanchions welded on the back line up with the 88 device on the interior. The optional key cylinder locks and unlocks the thumb piece. The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.
Von Duprin part # 880TP-R
88TP- -
Von Duprin 99 Panic Device Only
The Von Duprin 99 Rim Panic device has been around since the late 1970's and has gone through a couple of improvements. One of the great things about the 99 is the availability of replacement parts. Even when the device is upgraded, the upgraded parts will work with the older versions that can be close to 40 years old. This device is for all types of single and double doors with mullions. The device is UL Listed for Panic Exit Hardware and is considered Grade 1, the heaviest duty rating possible. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed, meaning it will work on Left and Right hand doors. Ships with all the mounting screws and the 299 Strike.
99EO -
Von Duprin Strike 385A
The Von Duprin Strike 385A is used on the floor for the Von Duprin 2227, 8827, 9827 and 9927 Surface Vertical Rods. Von Duprin recommends this strike if you are mounting the bottom strike in wood. The strike face plate outside dimensions are 2-1/4" x 2-1/4" with an inside dimension of 1-1/8" by 1". This floor strike features a bolt that can be cemented into the floor. This is an optional strike when added security is needed. Zinc plated finish.
385A -
Von Duprin Strike 1609
The Von Duprin Strike 1609 strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the Von Duprin 22/2227, 88/8827, 98/9827 and 99/9927 combinations. The strike base measures 1-1/16" wide by 3-1/4" high, the lip projects out 7/8". The three slots are 1-1/4" on center. This strike ships with the mounting screws. This Strike is not rated for Fire Doors, which are usually interior corridor doors.
Von Duprin Part # US19-Black finish
1609 -
Von Duprin 88 Tube Attaching Ring 090021
The Von Duprin 88 Tube Attaching Ring 090021 is also used on the Von Duprin 55. The ring fits over the device lever arm, and is expanded by the Wedge (88R90) and the Wedge Tite Screw (88R100). When the Wedge Tite Screw is tightened the Ring expands and keeps the crossbar parallel to the door. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110 -
Von Duprin 88 Lever Arm Left Hand 050439
The Von Duprin 88 Lever Arm Left Hand 050439 replacement lever arm for all the Von Duprin 88 exit devices. Usually replaced due to the dogging screw stripping out. The arm includes the Wedge, Wedge Ring, Wedge Tite Screw and Dog Screw, and sometimes the axle.
Von Dupin part # 050439
Old Part # 10072988R70- -
Von Duprin 8827 Top Latch Case 050460
The Von Duprin 8827 Top Latch Case 050460 is for non fire rated doors. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted position.
Von Duprin part # 050460
Old Part # 10175088VR10 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Von Duprin 22 End Cap Only 968601
The Von Duprin 22 End Cap Only 968601 is the end cap that goes on the hinge side of the door. When the cap breaks off the Dogging Cover Plate just slides off. Works on all of the Von Duprin 22 exit devices. If you need the bracket also, please order part # G22R10. Black plastic construction. As of October 1, 2014, Von Duprin no longer sells just the Plastic Cap Only. The complete End Cap and Bracket 900981 will be shipped in its place.
Von Duprin Part # 968601
G22R25 -
Von Duprin 2227 Bottom Latch 050090
The Von Duprin 2227 Bottom Latch 050090 replaces and updates all 2227 bottom latches to the new style if you device was shipped before October 1998. If your device was shipped after October 1998 then use the G050401.
Includes screws and bracket
Von Duprin Part # 050090
G22VR120 -
Von Duprin 2227 Rod Guides Assembly 112063
The Von Duprin 2227 Rod Guides Assembly 112063 works on all of the Von Duprin 2227's, and replaces the older style that featured the plastic cap and the springs. This device is used to add strength and rigidity to the top and bottom rods on there surface vertical rod.
Von Duprin part # 112063
G22VR80- -
Von Duprin Strike 248L-4
The Von Duprin 248L-4 Strike is used as a Bottom Surface Mounted Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 248L-4 strike measures 9/16" wide by 2-1/2" high with a hole spacing of 1-7/8. The strike projects out 3/8". Ships with shim and mounting screws. Burnished steel construction.
Von Duprin Part # 248L-4
248L-4 -
Von Duprin 2227/3327A/9927 Top Latch 050400
Von Duprin 22, 33, and 9927 Top latch
This latch is used on the 2227, 3327A, and 9927 Surface Vertical Rod Devices. This latch is for use on devices shipped after October 1998. This is usually the problem if your bottom rod is dragging on the floor. Includes screws.
Von Duprin Part # 050400
G050400 -
Von Duprin 8827-F Top Latch Cover Kit 050465
The Von Duprin 8827-F Top Latch Cover Kit 050465 the Top Latch Cover for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted position.
Von Duprin Part # 050465
Old Part # 96120688VR30F -
Von Duprin Thumb Piece 970488
The Von Duprin Thumb Piece 970488 is just the thumb piece only, rivet not included. Cast bronze construction, and then plated to the selected finish. 5-1/8" overall length, but note that the length is usually cut down in the field depending on the thickness of your door.
Von Duprin Part # 970488
Old Part # 960303G970488- -
Von Duprin NL Drive Screw 090074
Von Duprin NL Drive Screw 090074
The 090074 NL Drive Screw is used on the Von Duprin 22, 98 and 99 Exit Devices to control the rotation of the key cylinder cam. This small set screw, screws into the back of the chassis assembly next to the receptor for the Rim Key Cylinder. The set screw measures 5/16" long by 3/16" diameter. Note: When the NL drive screw is left in back of device, the outside cylinder will function only as a Night Latch. The Night Latch function means the door can only be opened, but not dogged open with the key cylinder.
Von Duprin Part # 090074
Old Von Duprin Part # 970441G090074 -
Von Duprin 6000 Series Solenoid Kit
The Von Duprin 6000 Series Solenoid Kit is used to replace burnt out solenoids on there 6000 series. To order determine the voltage and whether you have fail safe or fail secure.
Part # 050237 12 VDC (Fail Safe & Fail Secure)
Part # 050239 16 VDC (Fail Safe & Fail Secure)
Part # 050240 24 VDC (Fail Safe & Fail Secure)G0502xx