Search results for: 'fire door parts american device h 1600'
-
Jackson 1085 Panic Device Concealed Vertical Rod
The Jackson 1085 Panic Device is one of a few original manufactures of Panic Hardware for aluminum framed glass doors, or storefront doors. The 1085, 1095 along with their door closer the 20-330 were installed on about half of these doors in the 1970's and 1980's. They were installed on Vistawall and Kawneer doors just to name a few. Universally recognized as the standard for aluminum storefront hardware it is made of high tensile strength aluminum. The device is Non Handed, Comes with 45" cross bar that is easily cut in the field. Also includes the Concealed Vertical Rods, Screws and Strikes.
Replacement parts are available, in stock!
1085EO -
Jackson Panic Device 1295 Push Pad End Cap Package
Jackson Panic Device 1295 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2677
New Jackson Part # 30-2654G302677-xx -
Jackson 1095P Paddle Panic Hardware
The Jackson 1095P Paddle Panic Hardware is an alternative to the cross bar or push pad style panic hardware. The device is the same as the Jackson 1095, but with a paddle instead of the cross bar. This device is for use on aluminum or steel doors only. The device is mounted on surface studs that are tapped into the door. On a wood door they will pull out.
Right Hand Reverse Shown
1095P- -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Jackson Panic Device 20-1266 2085/2095 End Cap
Jackson Exit Device 2085/2095 End Cap
The Jackson Exit Device 2085/2095 End Cap measures 3-1/8" high, by 1-1/8" wide, and has a projection of 1-15/16". The mounting lugs are 1-3/8" on center and project out 1".
Jackson Part Number 30-1266-628 Aluminum
Jackson Part Number 30-1266-313 Dark BronzeG301266- -
Jackson Panic Device 2085 Dogging Assembly LH/RHRB
Jackson Exit Device 2085 Dogging Assembly LH/RHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2462
This spring would be for the Device on the Right, shown below.
G302462 -
Jackson 1095 Panic Rim Device
The Jackson 1095 Panic Hardware was one of the first devices universally recognized as the standard for aluminum storefront hardware. Made of high tensile strength aluminum. It ships complete with both housings, crossbar, all the fasteners, and the strike. Comes with 45" cross bar that is easily cut in the field.
1095EO -
Jackson Panic Device 2085 Dogging Assembly RH/LHRB
Jackson Exit Device 2085 Dogging Assembly RH/LHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2467
This spring would be for the Device on the Left, shown below.
G302467 -
Jackson Panic Device 1095 Standard Strike
The Jackson Panic Device 1095 Standard Strike is a strike they have been using for the past 20 years. You might have one of the older roller strikes, but this will work in its place. The older style roller strike is no longer available. Jackson Exit Device part # 30-2436.
G109556 -
Jackson Panic Device Top Bolt Guide Assembly 1085/1285/2086
The Jackson Panic Device Top Bolt Guide Assembly is used on the 1085, 1285, and 2086 hardware. The piece works by sliding over the top rod when the device is opened. This keeps the rods retracted until the Plunger hits the Trip Assembly when it is closing. Upon hitting the Trip Assy, the plate slides over and the rods retract. It measures 1-1/2” deep x 1-1/16” wide x 15/16” tall, with a hole spacing of 3/4" on the mounting screws. Assembly includes the mounting screws. The Jackson Part number is 30-934.
G108518 -
Jackson Panic Device 1095 Active Housing
The Jackson Panic Device 1095 Active Housing is the working side of the 1095 panic hardware. The housing comes will all the internal parts, including the latch bolt. The distance between the mounting studs on this case is 6-5/16". Jackson part # 30-988 Right Hand Body, and part # 30-989 Left Hand Body
Left Hand Housing shown in the aluminum finish.
G1095xx -
Jackson Panic Device 1285 Push Pad End Cap Package
Jackson Panic Device 1285 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2661
New Jackson Part # 30-2652-628 or 30-2652-313G302661- -
Jackson Panic Device Center Case 1085/1095
The Jackson Panic Device Center Case 1085/1095 is for use with the 1085 devices for both and left, and the inactive case of the 1095. Case is easily removed by loosening the two 1/8" Allen screws and one on the bottom. Includes everything in the housing. The distance between the mounting studs on this Case is 6-5/16"
Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm AssemblyHousing Shown in Aluminum
G1085XX -
Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117
The Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117 is a replacement for the Screw Driver Headed Dogging Pin. Now instead of using a screw driver you can use the handy thumb piece instead. The package comes with new set screw, spring, and of course the pin. Jackson part number 30-1117.
G108554TP -
Jackson Panic Device Crossbar 1085/1095
The Jackson Panic Device Crossbar is for use on the 1085 and 1095 hardware. The bar is 45" long and can be cut in the field with a chop saw or hack saw. There is a groove the entire length of the bar for added and strength and for the thread forming screws to thread into. The Jackson part number is 30-733-PKG, and it ships with the cross bar screws.
Jackson Part # 30-744PKG or 30744PKG
G108520- -
Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558 -
Jackson Panic Device 1085 And 1095 Dogging Pin
The Jackson Panic Device 1085 And 1095 Dogging Pin is the piece that keeps the hardware in the open position during business hours. It is activated by pressing the crossbar and then turning the flat head screw driver head. The pin is held in the housings with a screw, which is located on the back of the housing. This pin has been used since about 1988 or so, the old style are no longer made, but they had a roll pin that was used to hold it in place. This package comes with a new spring, set screw and the pin. The Jackson part number on this is 30-1115.
G108554 -
Jackson Door Closer Offset Arm - 20-1312-LC
The Jackson Door Closer Offset Arm - 20-1312-LC is the replacement arm and track for the Jackson 20-330 Door Closer. The track measures 12-7/8" long by 1/2" thick, and the arm has an overall length of 12-15/16" long with an offset of .826". This set is for use with single acting doors with a 3/4" offset. Package includes the arm and track.
Jackson part # 20-1312-LC
G201312LC -
Jackson Door Closer Offset Arm 20-1134LC
The Jackson Door Closer Offset Arm 20-1134LC is the arm and track assembly for the 20-330 concealed closer. The arm measures 12-15/16" long with .919" offset, and the track measures 1/2" thick by 12-7/8" long by 1-9/32" wide. The track includes the nylon slide, pin and retaining ring.
Jackson part # 20-1134-LC
G201134LC -
Jackson Door Closer Offset Arm - 20-900-LC
The Jackson Door Closer Offset Arm 20-900-LC is used with the 20-330 concealed closer for single acting offset mounted doors. The arm measures 12-15/16" long by 1/2" thick with a 1.012" offset. The track measures 25/32" deep by 29/32" wide by 14" long. The track includes the nylon slide, pin and retaining clips.
Jackson Part # 20-900-LC
G20900LC