Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The 6114 has a 3/4” latch bolt throw, 7” face plate length, 1-7/8” width, and projects1-9/16”. The lock retrofits the Folger Adams FD 310-5. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
The Von Duprin 990DT Trim is known as a Dummy Trim. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990DT-R&V.
The Von Duprin Latch Mounting Bracket 050546 is used on the 2227, 3327 and 9927. It is for use with the 050400, 050401, 050091 and 050090 Surface Vertical Latches.
Von Duprin Part # 050546 Old Von Duprin Part # 971567
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
The Von Duprin 88 Wedge Ring 090020 is also used on the Von Duprin 55's. The Wedge Tite Screw applies pressure on the Wedge which expands the Tube Attaching Ring to grip the Cross Bar. Measures 5/8" on the flat edge.
The Von Duprin 6000 Series Solenoid Kit is used to replace burnt out solenoids on there 6000 series. To order determine the voltage and whether you have fail safe or fail secure.
Part # 050237 12 VDC (Fail Safe & Fail Secure) Part # 050239 16 VDC (Fail Safe & Fail Secure) Part # 050240 24 VDC (Fail Safe & Fail Secure)
The Von Duprin 900620 35/3348 98/9947 Adjusting Screw Package is used to adjust the concealed vertical rods. This package is used on the 3347, 3547, 3347-F, 3547-F, 9847, 9847-F, 9947 and 9947-F. This is a package of 2.
The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.
Von Duprin Part # 050328 Old Von Duprin Part # 967616
The Von Duprin 1654-4954 Mullion Brackets 050330 are the top and bottom mullion fittings for the 1654 and 4954 Mullions. . Includes Top and Bottom Fittings, screws and mounting shields.
The Von Duprin Dogging Adapter 090043 is the piece that the 090042 and 090040 fit through and lock in place. These piece very rarely has to be replaced. The Shaft 090040 is usually the part you need to replace. We sell these individually.
The Von Duprin 9927 Center Case 050021 center case replaces all earlier versions of the 9827 and 9927 Center Cases. Everything shown in the picture is included with the product. Along with all the mounting screws.
The 8827 Special Chassis Nut goes on the ends of the 8827 Chassis Tie Rod. The Nut is threaded all the way through so the cover mounting screws can then be threaded on it also. The nut is 3/8" long by 1/4" hex.
Von Duprin Part # 050277 Old Von Duprin Part # 960652
The Von Duprin 8827 050466 Top Latch And Cover is the 050460 (latch) and 050464 (cover) in one convenient package. The package includes the cover screws and mount screws.
The Von Duprin 900894 230L Tailpiece Auxiliary includes the Tailpiece (steel), Tailpiece Guide (nylon), and the Pine Tree Clip (nylon). The Tailpiece measures about 2-1/2" x 1/4" x 3/32" thick.
The Von Duprin 8827 050467 Bottom Latch And Cover is the 050461 (latch) and 050464 (cover) in one convenient package. The package includes the cover screws and mount screws.