Search results for: '1260 ingersoll rate panic door handle parts lcn'
-
Glynn-Johnson Overhead Door Holder 90 Series Surface Mounted
The Surface Mounted Glynn-Johnson 90 Series Overhead Door Holder are the most rugged models available for heavy-duty applications. The channel is surface-mounted to the door, most often with barrel nuts, and the jamb bracket is surface mounted to the jamb, requiring minimal door and frame preparation.
GJ90 -
Adams Rite CVR/Mortise Metal End Cap 41-0901-05-IP
Plastic end cap for all Adams Rite Concealed Vertical Rod and Mortise devices, specifically the 8300, 8500, and 8600 Series.
Plastic cap measures 2-3/8" high by 1-1/16" wide by 1-1/4" projection. The metal tab measures 1-3/16" wide by 5" long.
Adam Rite Part # 41-0901-05-IP
G41090105 -
Falcon Dor-O-Matic STK45 Surface Strike
Falcon Dor-O-Matic STK45 Surface Strike
This strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the 1590, 1790 and 2090 Rim Devices. The strike base measures 1-5/16" wide by 3-1/4" high, and 1/4" thick. The three slots are 1-1/4" on center. This strike ships with the mounting screws.
US19-Black finish
STK45 -
Von Duprin 154 Mullion Stabilizer Package
The Von Duprin Mullion Stabilizer Package are used with Von Duprin Mullions to stop any deflection on the mullion, which may cause the exit devices to release. We run into issues where people are able to shake the door, and the door opens. The package includes two sets of stabilizers and all the mounting screws.
G154- -
Cal-Royal 9800 Rim Device
The Cal-Royal 9800 Rim Device is a grade 1 Heavy Duty Exit Device. The 9800 has the same template as the 8800 and 9800 with escutcheon lever trim. The 36 inch device will be 32 inches wide and can be cut down an additional 2" to fit doors as narrow as 30 inches. The 48 inch will be 44 inches wide and can be cut down to fit doors 36 inches wide. The device is non handed, meaning it will work on a left hand reverse or right hand reverse door. Strike and mounting screws are included.
9800EO- -
Monarch 19 Series Hex Dogging Kit
Falcon/Monarch 19 Series Hex Dogging Assembly and Cover have been changed. As of April 12, 2022 the kit now includes a new style dogging assembly also.
We know this kit will work on the 19/24/25 Series, and are not sure if it will work on the Monarch 17/18 Series Dogging Cover goes over the dogging mechanism on the hinge side of the exit device. Sometimes when the end cap goes missing, this cover plate also disappears.
Monarch old part #s 195 and 194
Monarch/Falcon new part #'s 650297 and 650303Size is the width of the Device, a 36 inch device is usally only 32 inches wide, a 48 inch device is usually about 42 inches wide.
G19R80- -
Ives Roller Bumper Straight Arm 6" RB472
The Ives Roller Bumper Straight Arm 6" RB472 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 6" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB6 or GJRB6.
GJRB6- -
Full Mortise Heavy Duty Hinge
The Full Mortise Heavy Duty Hinges are standard butt hinge. They are designed for heavy weight doors with a high frequency of usage. These are ideal for exterior doors in schools, hospitals and other commercial venues. The hinge offers four bearings, one between each leaf of the knuckle. They are constructed of 7 gauge (.180”) steel that is then plated or paint primed. We sell them in boxes of 3 hinges, and they ship with machine and wood screws.
Shown in brushed chrome
G300XX -
Sargent Regular Arm 25-O
The Sargent Regular Arm 25-O is now used on all of there commercial grade closers. This is the standard arm shipped with about 90 percent of there closers. This arm is for use with the 350, 1430, and 281 closers, and will work on the 1230 and 1250 models also.
Sargent Part # 25-0
350RA- -
Von Duprin Dogging Hook 090044
The Von Duprin Dogging Hook 090044 is the piece that grabs the push bar mechanism and keeps it in the dogged position. The does wear out, but it takes a long time. This piece is used on the 22, 33A, 35A, 98 and 99 series devices made after 1997. We sell this part individually and it is #5 on the diagram.
G090044 -
Von Duprin 2227 Bottom Latch 050090
The Von Duprin 2227 Bottom Latch 050090 replaces and updates all 2227 bottom latches to the new style if you device was shipped before October 1998. If your device was shipped after October 1998 then use the G050401.
Includes screws and bracket
Von Duprin Part # 050090
G22VR120 -
Norton 7700 Power Track Hook-Up Boxes
Norton 7700/7705PT Hook-Up Boxes come in two voltages, 24 and 120, and two configurations Hinge Side and Stop Side. Hinge Side means the track is on the side of the door that you can see the Hinges, also know as the pull side. Stop Side means the track is on the push side of the door.
PTOHB- -
Von Duprin 2227/3327/9927 Bottom Latch 050401
Von Duprin 22, 33, 9927 Bottom latch.
Used to replace the bottom latch on the Von Duprin 2227, 3327A, and 9927 on devices shipped after October 1998.
Includes screws and sometimes the bracket
Von Duprin Part # 050401
G050401 -
Adams Rite 8600 Electric Latch Retraction Concealed Vertical Rod
The Adams Rite 8600EL Electric latch Retraction Concealed Vertical Rod is designed for narrow stile aluminum framed glass doors. The device will fit on stile widths of 2" or more. The EL version We recommend this device for replacement or upgrading your current 8600 to Latch Retraction, modifying your existing door to this exit device will be labor intensive. The 8611EL would be for the aluminum finish and the 8622EL would be or the dark bronze finish.
This device is Electrified, please see the 8600 for the non Electric Device.
8600EL -
Adams Rite End Cap
On this Adams Rite End Cap we sometimes find the number HX0471 cast into the Black Plastic construction. It measures 2-3/8" high by 1" deep, with a projection of 1-1/4". It is used on the 8099, 8100, 8200, 8300, 8400, 8500, 8600, 8700, 8800 and 8900.
Adams Rite Part # 25-0471-IP
G250471 -
Reinforcing Pivot Hinge 4-1/2"
Reinforcing Pivot Hinge - For use with 4-1/2" wide butt hinges
3/4" to center line of 4-1/2" hinge pin.
Pin uses large pin and bushing.
Used to dampen vibration and increase
strength to your full mortise butt hinges.
Constructed of heavy duty cold rolled steel.
Made of Zinc Plated Steel
Supports weights up to 300 lbsManufacturer part # B1923
Our part # DR1923 for Right Hand, DL1923 for Left HandThese hinges are no longer handed, you can select right or left, but the hinges will work both ways.
B1923 -
Floor Mounted Dome Stop FS439
The Ives Universal Dome Floor Stop FS439 is constructed of cast zinc or stainless steel, depending on the finish. The stop measures 1-1/2" high, with a base height of 1/4" and base diameter of 1-7/8". The pad has a height of 1-1/8" from the floor.
Ives Part Number FS439
GFS439- -
Corbin Russwin 681F618 ED4200S Latch Assembly
Corbin Russwin ED4200S Latch Assembly
The Corbin Russwin ED4200S 681F618 Latch Assembly is used on the Narrow Stile SecureBolt Exit Device. The difference between the ED5200S and ED4200S Latch Assembly is the location of the Hub. Hub on the ED4200S Latch Assembly is located on the center line of the Assembly Mounting Screws.
Corbin Russwin Part # 651F618
The Hub Position on this Latch is the ED4200
G681F618