Search results for: 'hinges used on swinging door for kit'
- Did you mean
- hing used on swinging door for kit 0
- hinge used on swinging door for kit 0
- Related search terms
- door series 30 push bar panic exit dor parts 1311
- door series 30 push bar panic exit dog parts 1308
- door series push bar panic exit dor cal parts 1308
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit dent parts 1306
- door series 30 push bar panic exit deep parts 1310
- door series 30 push bar panic exit drop parts 1307
- door series 30 pull bar panic exit deep parts 1309
- door series 30 pull bar panic exit dead parts 1306
- dooramatic door series 30 push bar panic exit devic parts 1315
-
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Dor-O-Matic 1690/1790/2390 Dogging Assembly PBX-16
Dor-O-Matic 1690/1790/2390 Dogging Assembly PBX-16
Falcon Doromatic 1690, 1790, and 2390 replacement dogging assy. The dogging assembly is used to dog the door in the open position, so people can enter the building without having to unlatch the door for the inside or with a key on the outside. The KIT.1197 comes complete with mounting screws. Some of the earlier version where riveted into the rail, so you might need to drill out the rivets, the screws shipped with KIT.1197 have self tapping thread forming screws.
Doromatic part # KIT.1197
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts Breakdown
Falcon / Dor-o-Matic 2390 Parts Break DownGPBX16 -
Finger Protector For Doors - Exterior Pull Side
Door Finger Protector - Exterior Pull Side
This model is specifically designed for exterior doors on the pull side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts
Our part # on this is GFG7 for the 78" length, and GFG7+ for the 83" length.
GFG-D -
International 8600 Series End Cap
The International 8600 Series End Cap is used on the hinge side of the the exit device. This cap includes the mounting bracket and the mounting screws. It is constructed of a die cast metal for years of service. The piece measures 2-3/8" by 2-1/4" by 1-1/2". This end cap is used on the International Door Closer models, 8510S, 8610S, 8710S, 8810S, 8620S, 8530S, and 8650S devices, along with the same devices ending in F.
INT8600EC- -
Norton 7705 PTO PowerTrack Only
The Norton PTO PowerTrack for 7705 is a replacement piece for the 7705PTO Door Closer. The Track includes the Slider, Soleniod and new mounting screws. The Track measures 21-1/4" long with a hole spacing of 19" on centers. The PTO Track is for the Pull Side of the door, also known as the Hinge Side because you can see the hinges on that side. On the PTO Track Assembly you can see the Two Mounting Holes
Norton Part # PTO24 or PTO120
PTO24-- -
Norton Apollo Door Closer 7500
The Norton Apollo Door Closer 7500 has been around for quite a long time, and was designed to replace the older 7700, which are still made. The beauty of the 7500 is that is can be mounted left or right, push, pull or top jamb, were as the 7700 you had to specify all those attributes, which made stocking them a head ache. This is a Grade 1 closer, and is extremely durable. If you are looking for a 7500BF, the barrier free version, the new 7500 is barrier free, and will do the trick. This closer has a 2-3/8" x 6-3/4" hole spacing.
7500- -
Floor Door Stop / Holder
The F20 or GJF20 was a mainstay of Glynn-Johnson for years. When the Glynn-Johnson door stop line merged with H.B. Ives it became the FS20. This door stop has been discontinued from Ives, but we have been able find a large stock. This Floor Mounted Door Stop also holds the door open, when in the latched position you can push the door and the holding latch will flip up and unlock thee holding clip. It is constructed of cast bronze or brass and then plated to your desired finish. This stop has a 2-1/2" long base that is 1-1/2" wide. The overall height is 3-1/8" with a 2-5/16" floor to rubber stop centerline. For use with door undercut up to 2-1/2".
GJF20- -
Adams Rite 41-0903-IP Metal End Cap
The Adams Rite Metal End Cap is for the hinge side of the door and replaces the plastic version (25-0471). This cap can be used on the 3100, 3300, 3600, 3700, 3900, 8100, 8200, 8300, 8400, 8500, 8600, 8700, 8800 and 8900. We find the number 23-0600 cast in to the end cap.
Adams Rite Part Number 41-0903-IP or 41-0903-119
G410903 -
Cal Royal Panic Device 7760 Surface Vertical Rod
Cal Royal 7760 Surface Vertical Rod Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware.
Templating matches the Von Dupin 99 and 98
CR7760EO -
Finger Protector For Doors - Exterior Push Side
Door Finger Protector - Exterior Push Side
This model is specifically designed for exterior doors on the push side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts
Our part # on this is GFG5 for the 78" length, and GFG5+ for the 83" length.
GFG-C -
Falcon Mechanical Electric Latch (MEL) Retrofit Kit 47867200
New for 2024 the Falcon MEL 47867200 Mechanical Latch Retraction. Retrofits all 1690, 1790, 24 and 25 Series devices to Mechanical Latch Retraction. This new system uses the PS902 Power Supply. The benefits for the MEL Series over the Older EL series are lower power draw (1 amp verse 16 amp), and more flexible power supply location, longer wire runs and thinner guage wires.
G47867200 -
5" Kickdown Door Holder Grand Standard
5" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.
made by Grand Specialties 605z 605b
GJ605- -
Jackson 1085 30-1242 / 30-1243 Lever Arms
The Jackson 1085 30-1242 / 30-1243 Lever Arms are for use with the Jackson 1085 Housings, both sides. And the Jackson 1095 Inactive (hinge side) Housings. To determine hand, stand inside and look out the door, what is side is the arm on? If it is on the Right then order Right.
G10852x -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
4" Kickdown Door Holder Grand Standard
4" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.
GJ604- -
Cal Royal Panic Device 7700 Rim Device
Cal Royal 7700 Rim Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware. Uncompromising security and safety in single and double fire exit doors. Chassis mounted unit construction. Rim and vertical rod devices are non-handed and easily reversible. Available in many different functions. Lever and escutcheon trims are grade 1 construction with clutch free-wheeling mechanism. Rose and escutcheon covers 161 cut out.
Templating matches the Von Dupin 99 and 98
CR7700EO- -
10" Kickdown Door Holder Grand Standard
10" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 9-3/8" to the Floor when mounted.
Made by Grand Specialties 610z
GJ610 -
Falcon 600293 E Trim Solenoid PKG
The Falcon 600293 E Trim Solenoid PKG is used on the 25 Series Electrified Lever Trim. The unit can be used for Fail Safe or Fail Secure applications, depending on how the unit is installed. The piece measures 3/4" diameter by 1-1/2" long, with a 3/4" hole spacing. We sometimes find the numbers 661375-00 and 610306-00 on a stick on this piece. The package ships with two mounting screws. This unit is called the FSA/FSE Solenoid Kit on their parts breakdowns and in their price book. The Falcon/Monarch part number is 600293.
G600293 -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606- -
Von Duprin 9927 Top Vertical Rod 110573
The Von Duprin 9927 Top Vertical Rod 110573 is the standard top rod for door heights up to 7'1". The length of this rod is 35", less the fittings. For larger doors you can order a Rod Extension Kit, which at this point we do not have online. The rod is field adjustable if your doors are less then 7'1". The Old Von Duprin part # is 110573, and the Newer Von Duprin part # is 050512.
G99VR30- -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
International Door Closer 200 Series Overhead Concealed Closer
The International Door Closer 200 Series Overhead Concealed Closer has been in there line up for at least 20 years. It is designed as a replacement for the Jackson 20-330 concealed closer. This closer is a fixed spring closer with two adjustment valves, one for closing and one for latching speeds. It has a built in positive back stop and hold open positions, if you order the hold open option. To order select the desired opening swing (90 or 105 degrees) and hold open or non hold open. This is just the hydraulic cylinder, the arms are sold separately.
2000-B-230 105 with Hold Open
2000-B-231 105 with No Hold Open
2000-B-232 90 with Hold Open
2000-B-233 90 with No Hold Open2000-B -
Yale Door Closer 4400
The Yale Door Closer 4400 has been around for quite a long time, and was designed to replace the older 400, which are still made. The beauty of the 4400 is that is can be mounted left or right, push, pull or top jamb, were as the 4200 you had to specify all those attributes, which made stocking them a head ache. This is a Grade 1 closer, and is extremely durable. If you are looking for a 4400BF, the barrier free version, the new 4400 is barrier free, and will do the trick. This closer has a 2-3/8" x 6-3/4" hole spacing.
4400- -
Doromatic 1390 Dogging Kit PB-96
Dor-o-Matic 1390 Dogging Assembly. If you have a 1390 and the dogging is stripped, this is the part you need. The package includes the Dogging Cam (4270102815), Activating Cam (4270106551), Spacer (4270108584), and Retaining Ring (4299100732). The 1390 was discontinued in about 2003. Also known as a PB-96 Dor-o-Matic 1390 Dogging Assembly
Doromatic part # 4270106669
G4270106669