Search results for: 'door series 30 push bar panic exit detex parts'
-
Cal Royal Panic Device 7760 Surface Vertical Rod
Cal Royal 7760 Surface Vertical Rod Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware.
Templating matches the Von Dupin 99 and 98
CR7760EO -
Finger Protector For Doors - Exterior Push Side
Door Finger Protector - Exterior Push Side
This model is specifically designed for exterior doors on the push side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts
Our part # on this is GFG5 for the 78" length, and GFG5+ for the 83" length.
GFG-C -
Door Push Plate 89
The Door Push Plate 89 is drop forged plate that is .125" thick, and is made of Aluminum, Stainless Steel, Bronze or Brass, depending on the finish. The plate measures 3-1/2" wide by 15-3/4" long with a 1" projection. This plate is considered a combination push pull plate. Package ships with matching mounting screws.
GPH89- -
International Door Closer 784 Series
The International Door Closer 784 Series was discontinued about 10 years ago, but we still have some stock left.
FEATURES
Three Adjustment Valves: Closing and Latching
and back checkspeeds controlled by separate regulating Valves,
Universal application Non-handed for standard top
jamb or parallel arm installation.3/4" x 8-3/16" mounting holes
784- -
Von Duprin 9975 Panic Device Only
Von Duprin 9875/9975 mortise lock device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4-3/4" (121mm). The Von Duprin 9875 device has a smooth mechanism case and the Von Duprin 9975 device has a grooved case. The mortise lock device is non-handed
9975EO -
International 300 Series Adjustable Power Door Closer
The International 300 Series Adjustable Power Door Closer is one of there new closers to meet ADA requirements. With this door closer you can adjust the spring tension, closing and latching speed, even after it was installed. The Spring Power is adjustable all the way down to 8-1/2 pounds of resistance, making it ideal for areas with the elderly and children.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
Crash Chain Door Stop CS115
Crash Chain Door Stop CS115
- Specially designed for full-size exterior doors.
- Tear resistant, grey vinyl cover.
- Heavy duty compression spring assembled to both ends of chain
and end brackets. - Packed with sheet metal screws.
- Cast Brass brackets with solid, welded steel chain.
Available in 20-1/2", 25-1/2" and 30-1/2" lengths. Length is determined
by the location of your door closerPART # LENGTH
GCC205 20-1/2"
GCC255 25-1/2"
GCC305 30-1/2"GCC205- -
Sargent 2828 Series Rim Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warrantyG20EO- -
Door Push Plate 58
The Door Push Plate 58 is the only plate we have that is a forged plate. The forging process involves heat and pressure or pounding. The result is a very heavy and durable metal. This plate measures 3-1/2" wide by 15" tall, with a thickness of 7/32". This is one of the thickest plate we offer, and is the most sturdy.
GPH58- -
LCN 1250 Rw/PA Door Closer-New
The LCN 1250 Rw/PA Door Closer is a direct replacement for the Norton 1600, Yale 50, Falcon/Dor-o-Matic SC60, LCN 1260 and International 8050 Series Door Closers. It is ideal for low frequency and low abusive traffic areas, such as store front doors and interior doors. It features, a cast aluminum cylinder, 15 year warranty, powder coated finishes, and stick on mounting template. This door closer comes with the ability to mount on the push, pull or top jamb and is non handed. The door closer meets Grade 1-ANSI A156.4, UL/cUL, ADA and the Buy American Act certifications.
Hole Spacing 3/4” x 9-16”1250- -
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Von Duprin Panic Device 990NL Trim
The Von Duprin Panic Device 990NL Trim is known as a Night Latch Trim. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. The key locks and unlocks the interior exit device. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990NL-R&V. The key cylinder is sold separately.
99NLGlynn-Johnson Overhead Door Holder 70 Series Surface Mounted
Glynn-Johnson 70 Series Overhead Door Holder Surface Mounted are constructed primarily of Brass and 300 series Stainless Steel substrates, with several components fabricated of Steel treated to resist corrosion. Models in the 70 series utilize a 1/2"-diameter stainless steel bar, while the 79 series uses a 3/4" stainless steel bar. The bar is always provided in US32D. The spring, washer and nut are provided in a clear zinc finish.
GJ70Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558Door Push Plate 60
The Door Push Plate 60 has the classic half round design. The plate measure 8" wide and 16" tall, and is constructed of 16 gauge metal, which is .050" thick. This plate is similar to the GPH59 (Push Plate 59), but is a 1/2" wider and 1" taller. This plate ships with the matching finish screws.
GPH60-Von Duprin 6000 Series Solenoid Kit
The Von Duprin 6000 Series Solenoid Kit is used to replace burnt out solenoids on there 6000 series. To order determine the voltage and whether you have fail safe or fail secure.
Part # 050237 12 VDC (Fail Safe & Fail Secure)
Part # 050239 16 VDC (Fail Safe & Fail Secure)
Part # 050240 24 VDC (Fail Safe & Fail Secure)G0502xxLCN Door Closer 4021 FL
The LCN Door Closer 4021 FL is shipped with fusible link arm, standard plastic cover, and self reaming and tapping screws. This closer is designed to hold open fire doors, when the fusible link melts, it releases the hold open arm, so the door will close. Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Included arm has a fusible link that melts at 120 degrees, allowing to door to close. Door can be closed any time with a gentle pull. Closer mounts top jamb (push side), specify right or left swinging door. 4021 cylinder meets ADA requirements.
4020FLCal Royal Products 700 Series Door Closer
Cal Royal 700 Series Door Closer
Adjustable closing and latching speeds
holes spacing is 3/4" x8-3/16" for sizes 2 and 3, and 3/4 x 9-1/16" for the size 4. Size 2 is ideal for reduced power on interior doors, size 3 will be more powerful. Word of warning, the larger the spring size the harder it is to open the door.
Powder Coated Painted Finishes
5 year warranty720-Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544Door Push Plate 59
The Door Push Plate 59 has the classic half round design. The plate measure 7-1/2" wide and 15" tall, and is constructed of 16 gauge metal, which is .050" thick. This plate is similar to the GPH60 (Push Plate 59), but is a 1/2" more narrow and 1" shorter. This plate ships with the matching finish screws.
GPH59-Hager 5300 Series Door Closer
Hager 5300 Series Door Closer
Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control. The 5300 Series door closer is easy to install and maintain keeping your building safe and secure.
The Hager 5300 Series Door Closer body has a hole spacing of 3/4" x 9-1/6".
5300-International Door Closer 854P Series
The International Door Closer 854P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and whether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 42” interior or 36” exterior doors.
3/4" x 9-1/16" mounting holes
854-International Door Closer 855P Series
The International Door Closer 855P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 48” interior or 42” exterior doors.
3/4" x 9-1/16" mounting holes
855-International Door Closer 884P Series
The International Door Closer 884P Series is a very common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features three adjustment valves for closing,latching speeds and one for back check. The cylinder is constructed of precision cast aluminum. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 42” interior or 36” exterior doors.3/4" x 9-1/16" mounting holes
884-LCN 4050 Rw/PA Door Closer-New
The LCN 4050 Rw/PA Door Closer is a newer Closer and is a direct replacement for the Norton 7500, Yale 4400, and Falcon/Dor-o-Matic SC70 Series Door Closers. It features, a cast aluminum cylinder, 25 year warranty, powder coated finishes, and stick on mounting template. This door closer comes with the ability to mount on the push, pull or top jamb and is non handed. The door closer meets Grade 1-ANSI A156.4, UL/cUL, ADA and the Buy American Act certifications.
Hole Spacing: 2-3/8” x 6-3/4”
4050-International 8600 Series End Cap
The International 8600 Series End Cap is used on the hinge side of the the exit device. This cap includes the mounting bracket and the mounting screws. It is constructed of a die cast metal for years of service. The piece measures 2-3/8" by 2-1/4" by 1-1/2". This end cap is used on the International Door Closer models, 8510S, 8610S, 8710S, 8810S, 8620S, 8530S, and 8650S devices, along with the same devices ending in F.
INT8600EC-Hager 5100 Series Door Closer
Hager 5100 Series Door Closer
Hager 5100 Series Grade 1 door closer is constructed of cast iron, which makes it ideal for heavy duty, high use and abusive environments. Hager door closers are the only closers in the industry that are both BHMA certified and backed by a lifetime warranty.
The 5100 matches the hole spacing of the LCN 4040 or 4040XP
5100-