Search results for: 'dorma sizing door cal dorma minim von'
-
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Dogging Cover Plate. Plate covers the dogging assy, or hinge side of the exit device. This plate sides off when the plastic end cap breaks or goes missing.
Von Duprin Part # 968595 measures 10-3/4" Long for 3' devices
Von Duprin Part # 968596 measures 16-3/4" Long for 4' devicesG22R90- -
Von Duprin 8827 Top Latch Case 050460
The Von Duprin 8827 Top Latch Case 050460 is for non fire rated doors. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted position.
Von Duprin part # 050460
Old Part # 10175088VR10 -
Von Duprin 050534 EL Potted Circuit Breaker
The Von Duprin 050534 EL Potted Circuit Breaker measures 5" long by 1-1/4" wide and 7/16" thick including the wires. This piece spikes the current to the solenoid to open the door, then lowers the current to keep the device open. The 050534 has a plug for the two wire input, and a plug for the 3 wire output. This Potted Circuit Breaker is also used on the Doromatic/Falcon Exit Devices, EL1490, EL1590, EL1690, EL1790, and EL2390. We sometimes find the number 101031-00 and 2148 on a sticker.
Old Von Duprin Part # 110741
Von Duprin Part # 050534
Doromatic/Falcon Part # 050534-00G050534 -
LCN Door Closer 4031
The LCN Door Closer 4031 is shipped with forged regular arm, metal cover and wood/self-tapping machine screw pack. Non-sized (1-4) 4031 cylinder for exterior doors to 36” (914 mm) and interior doors to 48” (1219 mm). Closer mounts hinge side, top jamb, and parallel arm, on either right or left swinging doors. Closer meets ADA requirements. The hole spacing on this closer will not match the 4030's that LCN produced up to 1997, that was a completely different door closer.
We ship the 4031 Rw/PA
4030- -
Von Duprin Pull Handle 972466/972467
The Von Duprin Pull Handle 972466/972467 replacement Grip/Handle only, screws not included. Cast bronze construction, and then plated to the selected finish. The Grip measures 15/16" wide by 6" long. The center to center hole spacing is 5-1/2". This handle works on the Von Duprin 608, 696, 880, and 990 outside trim plates.
Von Duprin Part # 972466 and 972467
Old Part # 969925 and 959122G972466- -
Sargent Door Closer 351
The Sargent Door Closer 351 is the most heavy duty closer made by Sargent. This closers meets ADA requirements, meets the Buy American Act, and is certified Grade 1, the heaviest rating possible. The closer has the capability to be mounted on the push, pull or top jamb, and is non handed. It ships with arm, plastic cover, parallel arm bracket and all of the fasteners. The hole spacing is 2-1/2" x 9"
350- -
Von Duprin HD-QEL Baseplate 958004 and 040067
The Von Duprin HD-QEL Baseplate conversion is used to convert the older 33A/35A/98 and 99 HD-EL models to the newer motor driven devices. The HD-QEL is a Hex Key Dogging QEL Model. The QEL is a quiet motor driven solution.
Von Duprin Part numbers:
36" devices 958004
48" devices 040067G958004- -
CRL PR90 Door Closer
The CRL PR90 is a Grade 1 door closer, the heaviest rating possible. The template is the same as the LCN 4040 with the same features, latching speed, closing speed, back check and power adjustment from size 1 ADA compliant to size 6.
We offer the Standard Cylinder PR90 and also the Delayed Action PR92. Delayed Action will hold the door open for 15-20 seconds to allow handicap individuals to clear the opening before the door closes.
PR90 -
LCN Door Closer 1461
The LCN Door Closer 1461 series closer ships with regular arm, a slim line plastic cover, and self reaming and tapping screws. Non-sized (1-6) cylinder is adjustable for interior doors to 5’0” and exterior doors to 4’0”. Closer mounts hinge side, top jamb and parallel arm on either right or left swinging doors. The narrow foot print allows this door closer to be mounted on the top jamb and narrow stile doors without a drop plate.
We ship the 1461 Rw/PA
1460- -
Von Duprin 99 Mechanism End Cap 050014
The Von Duprin 99 Mechanism End Cap 050014, also known as 33A/35A/98/99/330/350 Impact Resistant End Cap Kit. Replaces all of the old versions of the 98/99 End Caps, the mounting holes may be different. Includes end cap, bracket and all screws
Von Duprin Part # 050014
G99R10- -
Von Duprin ALK Alarm Kit
The Von Duprin ALK Alarm Kit converts the Von Duprin 22, 33A, 35A, 98 and 99 Devices to an alarmed exit device. When you exit the 85 decibel alarm will sound. Powered by a standard 9 volt battery and is controlled by a Mortise Cylinder with a straight cam. When battery is low, the alarm will beep.
Mortise Cylinder NOT included.
Von Duprin Part # 22-ALK, 33A-ALK, 35A-ALK, 98-ALK AND 99-ALK
ALK -
Von Duprin 9927 Rod Guide Assembly 112063
The Von Duprin 9927 Rod Guide Assembly 112063 works on all of the Von Duprin 98 and 9927's. The guide keeps the rods from bowing or getting bent by hand carts, or rowdy patrons. Replaces the old style which had the cover and springs.
Von Duprin part # 112063
G99VR35- -
Von Duprin 88 Lever Arm Left Hand 050439
The Von Duprin 88 Lever Arm Left Hand 050439 replacement lever arm for all the Von Duprin 88 exit devices. Usually replaced due to the dogging screw stripping out. The arm includes the Wedge, Wedge Ring, Wedge Tite Screw and Dog Screw, and sometimes the axle.
Von Dupin part # 050439
Old Part # 10072988R70- -
LCN 4310HSA Sentronic
The 4311HSA SENTRONIC is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Single lever (track) arm closer is specifically designed for pull side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.
4310HSA -
LCN 4410HSA Sentronic
The 4412HSA SENTRONIC® is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Double lever arm closer is specifically designed for push side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.
4410HSA -
Von Duprin Panic Device 8827 Center Case 050415
The Von Duprin Panic Device 8827 Center Case 050415 is for use on the non fire rated 88 surface vertical rod. You can tell the difference by the dogging screw. If you have a Dogging Screw on your device, then this is the correct part. Includes the internal pieces, including the Rod Control.
Von Duprin part # 050415
88VR120- -
Von Duprin 3327A Panic Device Only
Von Duprin 3327A Exit Device Only
3327A and 3527A for all types of single and double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 3527A has a smooth mechanism case and the 3327A has grooved case. 3327A/3527A fits door stiles as narrow as 1-3/4". Newly designed device has a one piece center case cover.
3327AEO -
Von Duprin Panic Device 880TP Trim
The Von Duprin Panic Device 880TP Trim is for the 88 series only. The stanchions welded on the back line up with the 88 device on the interior. The optional key cylinder locks and unlocks the thumb piece. The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.
Von Duprin part # 880TP-R
88TP- -
LCN Door Closer Hold Open Head And Tube 3048 - 3048L
The LCN Door Closer Hold Open Head And Tube 3048 - 3048L. As the arm rotates the pivot point threads close on to the mounting bracket face and create a friction catch. If yours is new, try rotating the mounting plate 180 degrees so the threads tighten as it closes. This replacement part from LCN either breaks or wears out. The material some times wears out due to the friction of open and closing. But the biggest issue seems to be the point where the tube mounts to the cast iron connector.
Specify your current closers model number when ordering. Not all of the LCN closers have the same shape spindle on the door closer cylinder. Model Available here are the:
1260-3048
1260-3048L
1460-3048
1460-3048L
4010-3048
4010-3048L
4020-3048
4020-3048L
4040-3048
4040-3048L3048