Search results for: 'hing cal jackson panic device brown for td door'
-
Von Duprin Panic Device Keyed Mullion Retrofit Kit KR54
The Von Duprin Panic Device Keyed Mullion Retrofit Kit KR54 is used to convert the 1654 and 4954. Keyed Removable Steel Mullions makes removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when re-installed, without use of the cylinder key. Uses a 1-1/4´´mortise cylinder with a straight cam (Schlage cam reference B502-191). Cylinders are sold separately.
Von Duprin Part # 050168
KR54 -
LCN Door Closer 4111
The LCN Door Closer 4111 is known as the Smoothee, and is one of the heaviest duty door closers made. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 EDA model, which is a non hold open arm, on this page. The cylinder mounting holes are 2-1/2" by 6".
4110 -
Norton Door Closer Regular Arm
The Norton Door Closer Regular Arm is the standard arm that is shipped with the 9300, 1600, 8301, 8501 and 7500 door closers. It will also work with the Yale 2300, 50, 3301, 3501 and 4400 series door closers. This arm has had a bunch of different factory numbers over the years, including 1620-1, 7701-1 and 400-1.
16000- -
Detex ECL-230X Alarmed Deadbolt Panic Hardware-Single Point
The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm. The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.
ECL-230 -
Von Duprin Panic Device 990TP Trim
The Von Duprin 990TP Trim is known as a Thump Piece Trim. The key cylinder locks and unlocks the thumb piece, key cylinder sold separately. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990TP-R&V.
99TP -
Sargent 9898 Rim Panic Device
For Doors Wood or metal. 1 3/4" (44.5mm) thick standard. 2 1/4"(57mm) thick on order.
4 1/8" (105mm) miminum stile
Mounting Supplied standard with wood and machine screws.
Chassis Cover Brass, bronze or stainless steel
Chassis Nonferrous alloy
Crossbar 1" brass, bronze and stainless steel tubing.
Hand Reversible
Dogging Standard Allen key doggingG90EO- -
Von Duprin 9975 Panic Device Only
Von Duprin 9875/9975 mortise lock device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4-3/4" (121mm). The Von Duprin 9875 device has a smooth mechanism case and the Von Duprin 9975 device has a grooved case. The mortise lock device is non-handed
9975EO -
Rixson 117 Hinge Set
Application
includes 180 top pivot
Interior Doors
Weight to 300 lbs.*
Door Width up to 3'6"(1067mm)
Handed117 -
Von Duprin 98 Exit Device
The Von Duprin 98 Rim Panic device has been around since the late 1970's and has gone through a couple of improvements. One of the great things about the 98 is the availability of replacement parts. Even when the device is upgraded, the upgraded parts will work with the older versions that can be close to 40 years old. This device is for all types of single and double doors with mullions. The device is UL Listed for Panic Exit Hardware and is considered Grade 1, the heaviest duty rating possible. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed, meaning it will work on Left and Right hand doors. Ships with all the mounting screws and the 299 Strike.
98EO -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
Sargent 2727 Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warranty2727EO- -
Detex Advantex 10 Series Rim Device
Detex Advantex 10 Series Rim Device
The Detex 10 Series is a Super-Heavy-Duty panic device, built to with stand 1,000,000 cycles, twice the standard for Grade 1 rated devices. Designed for high-use and high-abuse environments. Non Handed with 1/4 turn hex dogging.
G10REO- -
Rixson 119 Intermediate Hinge
• Not load-bearing
• Available 3/4"(19mm) offset only
• Non-ferrous base material
• Used with 117, 117-1/4, 195, UNI closers,
127 closer
• Maintains door alignment
• Furnished with wood and machine screws119 -
Norton Door Closer Parallel Arm Bracket
The Norton Door Closer Parallel Arm Bracket is the bracket shipped with the Norton 1600, 7500, 8301, 8501 and 9300 series closers. This bracket is also used by Yale on there 2300, 50, 3301, 3501 and 4400 door closers. The factory part number on this is 1618A for Norton and 289A for Yale.
1600PA- -
Wall Door Stop / Holder WS20
The Ives Wall Door Stop / Holder WS20 is another door holder from Glynn-Johnson. The Chicago based manufacture made these for 40 plus years. When they were purchased from H.B Ives and merged into there line they became the WS20. This holder is constructed of cast brass and then plated to your desired finish. The hinged holding clip can be released by a gentle pushing on the door, which causes the clip to flip up and release the door. The piece ships with wood screws and anchors.
GJW20- -
Dor-o-Matic EL1590 Rim Panic Device
Effective December 20, 2024 the EL1590 has been discontinued. Falcon Doromatic is working on retro-fit plates to work with the MEL1690.
Dor-o-Matic/Falcon EL1590 Panic Device with Electric Latch Retraction
The Dor-o-matic 1590 is our heaviest device and offers a clean appearance with push pad styling and a variety of practical features. The Dor-o-matic 1590 is built with rugged steel operating mechanisms, and durable aluminum push bars and end caps.
Requires a Power Supply
Replacement parts are also available
Shipped with all screws and strikes.
EL1590EO- -
Cal Royal ESC6600 Escutcheon Lever Trim
The ESC6600 are non handed, with a Grade 1 thru bolted design. It features a clutch mechanism, double heavy duty spring support to prevent sagging and a hardened stell heavy duty spindle. Entrance function, key locks or unlocks lever, operates as a Classroom Function. Ships with mounting screws and a 6-Pin Schlage Mortise Cylinder.
ESC6600- -
Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50- -
International Door Closer 5530S SVR Device-Light Duty
International 5530S Surface Vertical Rod Device-Light Duty
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steelStandard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.Standard vertical rod accommodates 7’ or 8’ doors
We offer the aluminum and dark bronze finish online, the polished brass and stainless steel finishes are available.
5530S- -
Corbin Russwin ED5400 Panic Device
Corbin Russwin ED5400 Exit Device
Handing
Device is handed but easily field reversible.
Lever trim is handed.
Bar Length
Easily field cut to size.
Standard: 36" (914mm) bar fits 30"- 36" door.
Door Thickness
1-3/4" (44mm) standard.
Stile
Minimum width 4-1/2" (114mm).
Door Height
Standard top rod for 7' door.Replacement parts are also available
ED5400 -
Norton Traditional Door Closer 78 B/D
The Norton Traditional Door Closer 78 B/D is a door closer used in historic buildings. This is a replica of the original cast iron door closer used from the 1920’s to 1960’s. The new version is made of a cast aluminum alloy material, and should only be used when you are trying to keep historic designations. The hole spacing on this closer is 1-3/8" x 4-1/4”.
78B/D -
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Falcon / Doromatic Door Closer SC91
The Falcon / Doromatic Door Closer SC91 is an affordable, high quality closer for residential or light commercial applications. They used to be know as the Doromatic SC90, but in about 2008, they changed it to the Falcon SC91. This closer offers adjustable closing, latching and back check speeds, along with adjustable spring tension. It has the ability to be mounted on the push, pull or top jamb and is non handed. This closer is considered a Grade 3 closer, which is the lightest grade you can get. The hole spacing is 3/4” x 6-3/8”. We ship the SC91 Rw/PA.
SC90- -
Sargent 8700 Panic Device
For Doors Wood or metal. 1-3/4" (44 mm) thick standard.
minimum stile with trim and 3-1/2"
Mounting Supplied standard with wood and machine screws
Chassis Cover Cold drawn brass, bronze or stainless steel
Chassis Nonferrous alloy
Hand Handed. Specify RHRB or LHRB
Dogging Feature Allen-type dogging furnished standard.
Top and Bottom Bolts Brass, stainless steel8700EO -
International Door Closer 5510S Rim Device
International 5510S Rim Device-Light Duty
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steelStandard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.5510S- -
5" Kickdown Door Holder FS555
5" Kickdown Door Holder FS555
The H.B. Ives FS555 Kick Down Door Holder has been a staple in schools for many years due to its heavy duty construction and inexpensive price. It is constructed of durable cast iron, which has great strength characteristics. The shoe is made of a non-marring rubber, which is replaceable. The shoe is also held in place with a screw, which makes it a great option in schools and area of high vandalism. This holder will work on door to floor clearances of 3" or less. The hole spacing is 7/8" x 1-9/16".
Made by H.B. Ives
GJL555-