Parts
When you purchase panic and exit devices from RBA Door, every product will meet local building codes as well as your expectations for performance and quality. All panic device hardware and accessories are built with durability, convenience and value in mind. No matter the project, our panic devices are a well-built choice at a reasonable price.
-
Adams Rite End Cap
On this Adams Rite End Cap we sometimes find the number HX0471 cast into the Black Plastic construction. It measures 2-3/8" high by 1" deep, with a projection of 1-1/4". It is used on the 8099, 8100, 8200, 8300, 8400, 8500, 8600, 8700, 8800 and 8900.
Adams Rite Part # 25-0471-IP
G250471 -
Dor-O-Matic 1690/1790/1990/2090 Pinion PB5
The Dor-O-Matic 1690/1790/1990/2090 Pinion PB5 has been in use since the 1970's. This gear or pinion is what activates the latch or the rods on the 990, 1090, 1690, 1790, 1990 and 2090 devices. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are the same device, with the same parts, just a different name plate. The manufacture part number on this is CAM.102, PB5 or PB140.
G199005 -
Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft
The Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft is the piece that your dog key (allen wrench) fits into the lock the device in the open or dogged position. This shaft is used on the 1690, 1790, and 2390 device. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are basically the same device, with the same parts, just a different name plate. The part that the hex key fits into is only about 1/4" deep, because of that these tend to get rounded out, so the key will not move the shaft.
To remove the old shaft just pull with a pair of Channel Locks or Pliers. To reinstall, just press it back in to position, you might have to bend the holding tabs back down, but we very rarely have to do this. The manufacture part number on this is SHAFT.101.
GPBX16-SHF -
Dor-o-Matic 2090 Latch Link PB62
Dor-o-matic 2090 latch link
Dor-o-Matic 1090/2090 Repair Parts Breakdown
G209040 -
Dor-o-Matic 1490/1590 Compression Spring PB224
Dor-o-Matic 1490/1590 Dogging Compression Spring
Doromatic part # 4299101020 or PB224
GPB224 -
Dor-o-Matic 1690/1790 Lock Stile Push Bar End Cap PB318
Dor-o-Matic Lock stile Push Bar End Cap
The Dor-o-Matic -Falcon 1690/1790 Lock Stile Push Bar End Cap PB318 is used on the 1690 concealed vertical rod and 1790 rim device.This is the end cap for the push bar and is located closest to the active housing. Doromatic part # ECAP.129 or PB318
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts BreakdownGPB318 -
Dor-o-Matic 1790 Latch Pin PB320
Dor-o-Matic 1790 Latch Pin. This is the 1790 latch bolt axle.
The other component of this part would be the GPB328 Latch Retaining Ring Retaining
Doromatic part # 969467-89 or PB320
Dor-o-Matic 1790 Repair Parts Breakdown
GPB320 -
Dor-o-Matic 1690/1790/2390 Dogging Spring PB323
Dor-o-Matic 1690, 1790 and 2390 Dogging Spring
Doromatic part # 971493-76 or PB323
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts Breakdown
Falcon / Dor-o-Matic 2390 Parts Break DownGPB323 -
Dor-o-Matic 1790 Channel Spacer PB326
Dor-o-Matic 1790 Channel Spacer. This part is used on Dor-o-Matic 1790's with an outside key cylinder.
Doromatic part # SPACER.107 or PB326
Dor-o-Matic 1790 Repair Parts Breakdown
GPB326 -
Dor-o-Matic 1690 Actuator Arm Brkt Assembly PB338
The Dor-o-Matic Falcon Actuator Arm Bracket Assembly is used on the 1690 and 2390 devices.
Doromatic part # BRKTASY.107 or PB338
Dor-o-Matic 1690 Repair Parts Breakdown
GPB338 -
Dor-o-Matic 2390 Lift Bracket BRKT.143 PB336
Doromatic 2390 Lift Bracket
This cadium plated bracket attaches to the concealed vertical rods. When the push bar is depress, it raises and lowers the brackets and the rods. The bracket measures 2-7/8" long by 5/8" wide and has an overall projection of 3/4"
Falcon / Doromatic Part # BRKT.143
GPB336 -
Doromatic 2390 Moving Pushbar End Cap PB342 ECAP.143
Doromatic 2390 Moving Pushbar End Cap
Doromatic 2390 Moving Pushbar End Cap is the piece that fits on the end of the pushbar. The Endcap is 3-3/8" high by 1/4" thick, with an 1-7/8" projection. The Pushbar End Cap is constructed of die cast metal that is painted black.
Doromatic / Falcon Part # PB342 or ECAP.143
GPB342 -
Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558 -
Sargent Lever Return Spring 97-0425
The Sargent Lever Return Spring 97-0425 is usually a green color, however we have seen them in blue and red. The red spring has the same dimensions as the green, but the loop on the coil side of the spring was closed. Sargent is using this spring as a replacement for all of those springs. If you have a Sargent Panic Hardware, and the lever is sagging, or just hanging, this is most likely the problem. The spring measures 2-1/8" long by roughly 3/8" diameter.
Sargent part # 97-0425
G970425 -
Von Duprin 88 Tube Attaching Ring 090021
The Von Duprin 88 Tube Attaching Ring 090021 is also used on the Von Duprin 55. The ring fits over the device lever arm, and is expanded by the Wedge (88R90) and the Wedge Tite Screw (88R100). When the Wedge Tite Screw is tightened the Ring expands and keeps the crossbar parallel to the door. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110 -
Von Duprin 88 Axle Package 090006 090082
Von Duprin Exit Device 88 Axle Package
Von Duprin 88 Axle Package
New style axle snaps together, and replaces the old style which were screwed together with allen wrenches. This style of axle has been around since about 1990. The piece on the right is only used for taking the axle apart.
Von Duprin Part # 090006 or 090082
88R40 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60