Search results for: 'hinges cal jackson panic device bronz for td door'
- Did you mean
- hinges cal jackson panic device brook for td door 0
- hing cal jackson panic device bronz for td door 0
- hinge cal jackson panic device bronz for td door 0
- Related search terms
- door series 30 push bar panic exit dev parts 1306
- door series push bar panic exit devic parts 1306
- door series 30 push bar panic exit devic parts 1316
- door series 30 push bar panic exit drill parts 1307
- door series 30 push bar panic exit dead parts 1307
- door series 30 push bar panic exit de99 parts 1306
- door series 30 pull bar panic exit de99 parts 1306
- door series 30 pull bar panic exit deep parts 1309
- door series 30 pull bar panic exit dead parts 1306
- door o matic 1 panic device 1309
-
Jackson Panic Device Center Case 1085/1095
The Jackson Panic Device Center Case 1085/1095 is for use with the 1085 devices for both and left, and the inactive case of the 1095. Case is easily removed by loosening the two 1/8" Allen screws and one on the bottom. Includes everything in the housing. The distance between the mounting studs on this Case is 6-5/16"
Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm AssemblyHousing Shown in Aluminum
G1085XX -
Jackson 1095P Paddle Panic Hardware
The Jackson 1095P Paddle Panic Hardware is an alternative to the cross bar or push pad style panic hardware. The device is the same as the Jackson 1095, but with a paddle instead of the cross bar. This device is for use on aluminum or steel doors only. The device is mounted on surface studs that are tapped into the door. On a wood door they will pull out.
Right Hand Reverse Shown
1095P- -
Jackson Panic Device 20-1266 2085/2095 End Cap
Jackson Exit Device 2085/2095 End Cap
The Jackson Exit Device 2085/2095 End Cap measures 3-1/8" high, by 1-1/8" wide, and has a projection of 1-15/16". The mounting lugs are 1-3/8" on center and project out 1".
Jackson Part Number 30-1266-628 Aluminum
Jackson Part Number 30-1266-313 Dark BronzeG301266- -
Jackson Panic Device 1295 Push Pad End Cap Package
Jackson Panic Device 1295 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2677
New Jackson Part # 30-2654G302677-xx -
Cal Royal Panic Device 2000 Series Lever Trim
Cal Royal 2000 Series Exit Device Lever Trim
Non-handed Grade 1 (Clutch Style)
Cylindrical body hardened steel heavy duty tailpiece. For
1¾” and 2 ¼” doors. Prefix THI before part # for 2 ¼” door
thickness. Available for fire and non fire rated rim and
vertical rod exit devices.
Rose diameter 3 ½”, lever length 4 ¾”.ENTOOL- -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Cal Royal Panic Device 7700 Rim Device
Cal Royal 7700 Rim Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware. Uncompromising security and safety in single and double fire exit doors. Chassis mounted unit construction. Rim and vertical rod devices are non-handed and easily reversible. Available in many different functions. Lever and escutcheon trims are grade 1 construction with clutch free-wheeling mechanism. Rose and escutcheon covers 161 cut out.
Templating matches the Von Dupin 99 and 98
CR7700EO- -
Jackson Panic Device 1095 Standard Strike
The Jackson Panic Device 1095 Standard Strike is a strike they have been using for the past 20 years. You might have one of the older roller strikes, but this will work in its place. The older style roller strike is no longer available. Jackson Exit Device part # 30-2436.
G109556 -
Jackson Panic Device 1095 Active Housing
The Jackson Panic Device 1095 Active Housing is the working side of the 1095 panic hardware. The housing comes will all the internal parts, including the latch bolt. The distance between the mounting studs on this case is 6-5/16". Jackson part # 30-988 Right Hand Body, and part # 30-989 Left Hand Body
Left Hand Housing shown in the aluminum finish.
G1095xx -
Cal Royal 4400 Rim Panic Device
The Cal Royal 4400 Rim Exit Device has a Grade 2 rating. The device features a 3/4" Latchbolt, Roller Strike and a 1" diameter Crossbar. The device comes in a brushed chrome and dark bronze finish, and comes with either a 36" or 48" crossbar. You would need a 4-1/2" minimum stile width.
CR4400- -
Cal Royal Panic Device 7000 Alarmed
Cal Royal 7000 Alarmed Exit Device
Same as the Cal Royal 7700, but with these added features"
Alarm unit has internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated. The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off. The key switch to turn alarm off is a standard 1 ¼” cylinder with “C” keyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal. Alarmed units are supplied with a switch that monitors push rail only. Unit includes “EMERGENCY EXIT ONLY • ALARM WILL SOUND” decal for application on door or unit.
ALRM7700 -
Jackson Panic Device Top Bolt Guide Assembly 1085/1285/2086
The Jackson Panic Device Top Bolt Guide Assembly is used on the 1085, 1285, and 2086 hardware. The piece works by sliding over the top rod when the device is opened. This keeps the rods retracted until the Plunger hits the Trip Assembly when it is closing. Upon hitting the Trip Assy, the plate slides over and the rods retract. It measures 1-1/2” deep x 1-1/16” wide x 15/16” tall, with a hole spacing of 3/4" on the mounting screws. Assembly includes the mounting screws. The Jackson Part number is 30-934.
G108518 -
Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117
The Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117 is a replacement for the Screw Driver Headed Dogging Pin. Now instead of using a screw driver you can use the handy thumb piece instead. The package comes with new set screw, spring, and of course the pin. Jackson part number 30-1117.
G108554TP -
Jackson 1095 Panic Rim Device
The Jackson 1095 Panic Hardware was one of the first devices universally recognized as the standard for aluminum storefront hardware. Made of high tensile strength aluminum. It ships complete with both housings, crossbar, all the fasteners, and the strike. Comes with 45" cross bar that is easily cut in the field.
1095EO -
Jackson Panic Device 2085 Dogging Assembly RH/LHRB
Jackson Exit Device 2085 Dogging Assembly RH/LHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2467
This spring would be for the Device on the Left, shown below.
G302467 -
Cal Royal Panic Device 7760 Surface Vertical Rod
Cal Royal 7760 Surface Vertical Rod Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware.
Templating matches the Von Dupin 99 and 98
CR7760EO -
Jackson Panic Device Crossbar 1085/1095
The Jackson Panic Device Crossbar is for use on the 1085 and 1095 hardware. The bar is 45" long and can be cut in the field with a chop saw or hack saw. There is a groove the entire length of the bar for added and strength and for the thread forming screws to thread into. The Jackson part number is 30-733-PKG, and it ships with the cross bar screws.
Jackson Part # 30-744PKG or 30744PKG
G108520- -
Jackson Panic Device 2085 Dogging Assembly LH/RHRB
Jackson Exit Device 2085 Dogging Assembly LH/RHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2462
This spring would be for the Device on the Right, shown below.
G302462 -
Cal Royal Panic Device 2000 Alarmed
Cal Royal 2000 Alarmed Exit Device
Alarm units has an internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated. The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off. Jumper cable is provided to swich to continuous alarm. The key switch to turn the alarm off is a standard 1” cylinder with “C” keyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal. Alarmed units are supplied with two switches. One switch monitors the push rail and the other switch monitors the latch bolt for full proof security.
Unit includes “EMERGENCY EXIT ONLY. ALARM WILL SOUND” decal for application on door or unit.ALM2000 -
Jackson Panic Device 1285 Push Pad End Cap Package
Jackson Panic Device 1285 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2661
New Jackson Part # 30-2652-628 or 30-2652-313G302661-