Search results for: 'hinges us32d on swinging door for kick'
- Related search terms
- door series 30 push bar panic exit dor parts 1311
- door series 30 push bar panic exit dog parts 1308
- door series push bar panic exit dor cal parts 1308
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit dent parts 1306
- door series 30 push bar panic exit deep parts 1310
- door series 30 push bar panic exit drop parts 1307
- door series 30 pull bar panic exit deep parts 1309
- door series 30 pull bar panic exit dead parts 1306
- dooramatic door series 30 push bar panic exit devic parts 1315
-
Full Mortise Double Swinging Spring Hinge
Full Mortise Double Swinging Spring Hinge
Used mainly for commercial kitchen doors, or any commercial double swinging door. Sold in sets of 2 hinges, they will handle doors up to 75 lbs that are 1-3/4" thick. If you door weighs between 75 and 107 lbs, you should use 3 hinges. The door flange is designed for a standard 4-1/2" x 4-1/2" template mortise. Hinges ship with wood and metal mounting screws. They come in a standard Painted Primed Finish Gray.
The jamb flange is .100" thick, the door flange is .134" thick and the barrel diameter is 1.18".
GDA8145 -
Glynn-Johnson Overhead Door Holder 450 Series Surface Mounted
The Glynn-Johnson Overhead Door Holder 450 Series provide reliable and versatile surface-mounted overhead door control for all medium to light-duty applications. The visible components are available in a wide variety of architectural finishes to complement any design. The Glynn-Johnson 450 series holders and stops are designed for installation in virtually all types of doors and frames including doors with conventional butt hinges, offset pivots, continuous hinges, swing clear hinges and many other specialty hinges. The templates provided allow for variable mounting positions, ranging from 85° - 110° of opening.
The 450 Series replaces the older GJ360, GJ370 and GJ380 Series.
GJ450 -
Full Mortise Spring Hinge
The Full Mortise Spring Hinge is found in many hotels and motels across the United States. They are an inexpensive way to meet Fire Codes. An internal adjustable spring in the hinge closes the door when they are opened. So instead of using a door closer, you can use these spring hinges. One draw back is you can not slow the door down and they will slam shut. We do not recommend these self closing hinges if your door swings more than 110 degrees, chances are the spring will break. They are constructed of 10 gauge (.134”) steel that is then plated or paint primed. We ship them in boxes of 3 hinges, and they ship with machine and wood screws.
Shown in brushed brass
G400XX -
Glynn-Johnson Overhead Door Holder 100 Series Concealed Mounting
The Glynn-Johnson Overhead Door Holder 100 Series Concealed Mounting, provide the most reliable and versatile concealed overhead door control. They are designed for installation on virtually all types of doors mounted on conventional type butt hinges, pivots, continuous hinges, swing clear hinges and numerous other specialty hinges. When used in conjunction with many surface-applied door closers, Glynn-Johnson 100 series holders and stops provide the most effective control for entrance doors and vestibule doors of all types, as well as heavy or often used interior doors. Templates provided allow for variable mounting positions, ranging from 85° - 110° of opening.
Painted finishes are also available. Please Call 1-800-642-2403
GJ100 -
Bilco Barracuda DSO-PB for Out Swinging Doors with Panic Devices
The Barracuda DSO-PB is for use on Out Swinging 36" Doors with Exit Devices. It is constructed of heavy duty steel with a durable powder coated finish. The bar goes across the door frame and grabs the mounting cleat with an adjustable clamp. To secure the door, simply turn the handle until it is secured. They currently offer two models, one for jambs up to 5-3/4" and one for jambs greater than 5-3/4". This device ships with all of the hardware and a wall mounting rack for storage.
DSO-PB -
Bilco Barracuda DSO for Out Swinging Doors
The Barracuda Model DSO is for Out Swinging 36" Doors and provides up to 550 pounds of security. It is constructed of heavy duty steel with a durable powder coated finish. The bar goes across the door frame and grabs the lever or knob set with an adjustable clamp. To secure the door, simply turn the handle until it is secured. They currently offer two models, one for jambs up to 5-3/4" and one for jambs greater than 5-3/4". This device ships with all of the hardware and a wall mounting rack for storage.
Barracuda Part # DSO-1 and DSO-2
DSO -
Bilco Barracuda DSI for In Swinging Doors
The Barracuda DSI is designed for In Swinging 36" Doors. The user places the deive on the floor and slides the metal plates under the door. Then pushing outward on the handles engages the plates to the exterior door jamb. Then you simply install the locking pin to barracade the door. The device is manufactured of heavy-duty steel that is then coated in a durable powder coat paint. It will work on just about any door and comes in 6 different versions depending on your jamb width. It is lightweight and comes with a storage mounting rack, along with all the the needed hardware for installation.
Barracuda Part Number
4-3/4" DSI-2
5-3/4" DSI-1
6-3/4" DSI-3
7-3/4" DSI-4
8-1/4" DSI-5
8-3/4" DIS-6DSI -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
LCN Door Closer 1461
The LCN Door Closer 1461 series closer ships with regular arm, a slim line plastic cover, and self reaming and tapping screws. Non-sized (1-6) cylinder is adjustable for interior doors to 5’0” and exterior doors to 4’0”. Closer mounts hinge side, top jamb and parallel arm on either right or left swinging doors. The narrow foot print allows this door closer to be mounted on the top jamb and narrow stile doors without a drop plate.
We ship the 1461 Rw/PA
1460- -
Intermediate Hinge IP-1901 and IP-1902
Intermediate Hinge IP-1901 and IP-1902
Cast aluminum construction with steel bearings. The hinge measures 5" high by 2-1/2" wide. This hinge has a 3/4" offset. We find this hinge in the middle section of the door between the top and bottom hinges. Available in the Aluminum color and Dark Brown. See the dimensional information under more views.
Manufacture Part # IP-1901 and IP-1902
IP-1901 is for Left Hand Doors
IP-1902 is for Right Hand DoorsGIP1901- -
Rixson 27 Series Door Closer
• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustmentWhen Less All Parts is selected only the Cylinder is shipped, just the replacement hydraulic cylinder will be shipped
27-RIX -
LCN Door Closer 4031
The LCN Door Closer 4031 is shipped with forged regular arm, metal cover and wood/self-tapping machine screw pack. Non-sized (1-4) 4031 cylinder for exterior doors to 36” (914 mm) and interior doors to 48” (1219 mm). Closer mounts hinge side, top jamb, and parallel arm, on either right or left swinging doors. Closer meets ADA requirements. The hole spacing on this closer will not match the 4030's that LCN produced up to 1997, that was a completely different door closer.
We ship the 4031 Rw/PA
4030- -
Intermediate Hinge IP-2202 and IP-2201
Intermediate Hinge IP-2202 and IP-2201
Cast aluminum construction with steel bearings and axle. The set measures 3-1/2" tall with an 1-3/8" projection. This hinge is usually used an an intermediate hinge in between the top and bottom hinge.
Manufacture part # IP-2202 and IP-2201
IP-2202 is for Right Hand Doors
IP-2201 is for Left Hand DoorsGIP2201- -
Reinforcing Pivot Hinge 4"
Reinforcing Pivot Hinge 4" - for use with a 4" wide butt hinge
1/2" to center line of 4" hinge.
Used to strengthen and reduce vibration
to your current full mortise butt hinges.
Made of Zinc Plated SteelThese hinges are not longer handed. Please select hand when checking out, until our system is updated.
DX1921 -
ALREX Door Closer Hinge
The ALREX hinge is a full function hydraulic door closer hinge. It contains all the features of a door closer, closing and latching speed control, power adjustment, and optional hold open feature. They are available in 4, 4.5 and 5 inch (leaf height), and are currently available in Stainless and Black finishes.
Package includes 2 hydraulic closer hinges and one dummy, for a standard 3 x 7 foot door, 100 pound door.
Door Handing:
AX21 -
LCN Door Closer 4011FL | LCN 4011 FL
The LCN Door Closer 4011FL is shipped with fusible link arm, standard plastic cover, and self reaming and tapping screws. Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder (4011) adjustable for interior doors to 4’6” and exterior doors to 3’6”. Included arm has a fusible link that melts at 120 degrees, allowing to door to close. Door can be closed any time with a gentle pull. Closer mounts hinge side, specify right or left swinging door. 4011 cylinder meets ADA requirements.
We ship the 4011 FL
4010FL- -
BB83 Full Surface 4-1/2" Door Hinge-3 per box
The BB83 Full Surface 4-1/2” Door Hinge is a specialty hinge. The hinge fastens to the face of the door and the face or the door frame. These are five knuckle, two bearing with square edges. They are constructed of 10 gauge (.134”) steel that is then plated to the desired finish. We ship in boxes of 3 hinges with the wood and machine screw.
G80045- -
BB84 Half Surface 4-1/2" Door Hinge-Box of 3
The BB84 Half Surface 4-1/2” Door Hinge is a specialty hinge. The hinge leaf will mount on the door frame in the standard mortise position and the other leaf mounts on the door face. These are five knuckle, two bearing with square edges. They are constructed of 10 gauge (.134”) steel that is then plated to the desired finish. We ship in boxes of 3 hinges with the wood and machine screw.
G70045- -
BB82 Half Mortise 4-1/2" Door Hinge-box of 3
The BB82 half Mortise 4-1/2” Door Hinge is a specialty hinge. The hinge fastens to the standard mortise slot on the door and the other leaf mounts on the face of the door frame. These are five knuckle, two bearing with square edges. They are constructed of 10 gauge (.134”) steel that is then plated to the desired finish. We ship in boxes of 3 hinges with the wood and machine screw.
G60045- -
TH1100-HK1 Deluxe Hinge Kit
The TH1100-HK1 is the perfect solution for existing hinges that have failed, and is a quick and easy fix for compromised door openings. Deluxe Hinge Kit TH1100-HK1 comes in a package of two hinges, 2 1/4" shims, and 12 one-way mounting screws. The hinges are non handed, will work on Flush, and 1/8" offset door applications, have a self lubricating pin that rotates on anti-friction bearings, and have a vertical adjustment screw. They are constructed of an aluminum alloy.
TH1100HK1- -
Brushed Stainless Steel Door Kick Plate-14 Gauge .062
The Brushed Stainless Steel Door Kick Plate 14 Gauge .062 is the heaviest duty plate we offer . Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. We use only type 304 stainless.
Stainless Steel Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.40 per square inch depending quantity
Please allow 1 week shipping time
GKP-US32D-14ga -
Full Mortise Two Bearing Shim Hinge
The PBB Shim Hinge is for use in Fire Doors where the doors are not square. Putting cardboard or wood shims on fire doors is prohibited, so they have come up with a solution where one of the leaves are drilled tapped and a set screw is inserted. These hinges are only available in 4.5 x 4.5 sizes in brushed chrome finish. They are sold in boxes of three hinges and come with wood and machine screws. The base metal is steel.
SHBB81 -
Continuous Full Mortise Hinge
The Ives 112HD Continuous Full Mortise Hinge Geared Hinge measures 83" long and is constructed of extruded aluminum. This hinge is non handed, and will work on doors up to 48" wide and 450 pounds. You can easily cut this hinge in the field if your door is less than 83" high.
GFM100-
