Search results for: 'rollers for spring door base'
- Did you mean
- rollers for spring door brass 0
- rollers for spring door back 0
- roller for spring door base 0
- Related search terms
- door series 30 push bar panic exit dor parts 1311
- door series 30 push bar panic exit dog parts 1308
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit drill parts 1306
- door series 30 push bar panic exit dent parts 1306
- door series 30 push bar panic exit deep parts 1310
- door series 30 push bar panic exit detex parts 1307
- door series 30 push bar panic exit drop parts 1307
- door series 30 pull bar panic exit dead parts 1306
- dooramatic door series 30 push bar panic exit devic parts 1315
-
Corbin Russwin 651F61 Red Lever Spring
The Corbin Russwin 651F61 Red Lever Spring is the same part as the Yale Lever Trim Spring. Used on Yale and Corbin Russwin LHR or RH Doors on there outside trim Lever Handles. The spring has an 1-1/4" OD and 1-1/8" ID.
Yale Part # 60-7000-1225-999
Corbin Russwin # 651F61G651F61 -
Ives Gravity Type Door Coordinator COR9G
Gravity Door Coordinator 9"
The Ives COR9G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR9G-26D for use on pairs of doors with astragal on active door over 4' or with astragal on inactive door over 3'4" or with astragal on both doors over 2'10" Brushed Chrome Finish.Ives part # COR9G-26D 9" Arm Projection
COR9G -
Ives Gravity Type Door Coordinator COR7G
Gravity Door Coordinator
The Ives COR7G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR7G-26D for use on pairs of doors with astragal on active door up to 4' or with astragal on inactive door up to 3'4" or with astragal on both doors up to 2'10" Brushed Chrome Finish.Ives part # COR7G-26D 7" Arm Projection
1836 -
Full Mortise Double Swinging Spring Hinge
Full Mortise Double Swinging Spring Hinge
Used mainly for commercial kitchen doors, or any commercial double swinging door. Sold in sets of 2 hinges, they will handle doors up to 75 lbs that are 1-3/4" thick. If you door weighs between 75 and 107 lbs, you should use 3 hinges. The door flange is designed for a standard 4-1/2" x 4-1/2" template mortise. Hinges ship with wood and metal mounting screws. They come in a standard Painted Primed Finish Gray.
The jamb flange is .100" thick, the door flange is .134" thick and the barrel diameter is 1.18".
GDA8145 -
Dor-o-Matic 2090 Latch Spring PB61
Doromatic 2090 Latchbolt spring. Pushes out the latch bolt.
Doromatic part # SPRING.104
Dor-o-Matic 1090/2090 Repair Parts Breakdown
G209060 -
Dor-o-Matic 1990/2090 Spring Retainer SD45
Dor-o-Matic spring retainer. The retainer fits under the housing, by the dog screw and holds one end of the spring. The spring pin holds the other side.
Doromatic part # RETAIN.102
Dor-o-Matic 990/1990 Repair Parts Breakdown
Dor-o-Matic 1090/2090 Repair Parts BreakdownG199045 -
Von Duprin 090091 and 090092 Lever Control Springs Pkg 4
The Von Duprin 373L Lever Control Spring 090091 and 090092 are used on the 371, 373, 375 and 378 Lever Handles. The spring is used to return the lever to the horizontal position. Sold in packages of 4 springs.
Von Duprin Part #
090091 Left Hand Reverse
090092 Right Hand ReverseG09009x -
Von Duprin 55 Hinge Case Spring 090052
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
Von Duprin part # 090052
55R200 -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Sargent Lever Return Spring 97-0425
The Sargent Lever Return Spring 97-0425 is usually a green color, however we have seen them in blue and red. The red spring has the same dimensions as the green, but the loop on the coil side of the spring was closed. Sargent is using this spring as a replacement for all of those springs. If you have a Sargent Panic Hardware, and the lever is sagging, or just hanging, this is most likely the problem. The spring measures 2-1/8" long by roughly 3/8" diameter.
Sargent part # 97-0425
G970425 -
LCN Door Closer 1261
The LCN Door Closer 1261 Series combines the best features from the previous 1070 and 1370 into a single versatile and economical cast iron closer, with Tri mounting capability. The 1261 is the door closer I would recommend if you are tired of replacing your store front door closers because of leakage. The 1261 is the most heavy duty standard template closer that is made. This door closer will work on the push, pull or top jamb, and is non handed. The 1261 is adjustable spring sizes 1-5 and mounts to the most common commercial footprint. The 1261 also features a complete line of regular and extra duty arms, LCN’s peel-n-stick installation templates, a convenient spring adjust pointer. The hole spacing is 3/4" x 9-1/16", so it is considered a standard template closer. LCN also offers a 20 year warranty on this closer. The Brass finish is Painted Brass.
We ship the 1261 Rw/PA
1260- -
Von Duprin 992/994 Lift Spring 971573
Von Duprin 992/994 Lever Lift Spring 971573
The spring measures 1-5/8" long with a 7/16" diameter. We find two of these springs per 992 and 994 series lever trims. These springs help support the lever handle and return it to the proper position.
Von Duprin Part # 971573-00
G971573 -
Dor-o-Matic 1990/2090 Pin Spring RD10
Dor-o-Matic 990/1990/2090 Lever Arm Pin. This pin is what the spring attaches to.
Doromatic part # PIN.104
Dor-o-Matic 990/1990 Repair Parts Breakdown
Dor-o-Matic 1090/2090 Repair Parts BreakdownG199011 -
International 300 Series Adjustable Power Door Closer
The International 300 Series Adjustable Power Door Closer is one of there new closers to meet ADA requirements. With this door closer you can adjust the spring tension, closing and latching speed, even after it was installed. The Spring Power is adjustable all the way down to 8-1/2 pounds of resistance, making it ideal for areas with the elderly and children.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
Norton 9300 Door Closer-Discontinued
Norton Door Closer 9300
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- Friction hold open arm optional
- UL listed and compliant with UL10C for positive pressure
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" Hole Spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
9300- -
LCN Sentronic Door Closer 4314ME
LCN Sentronic Door Closer 4310ME
Standard LCN Sentronic Door Closer 4310ME series closer shipped with a 24V or 120V cylinder (please specify) on a mounting plate, metal cover, Swing-Free arm, track, track roller, and wood and machine screw pack. See 4310ME Series pages 23 & 24 for options. Sized cylinders for interior doors to 4’0”. Functions as full rack and pinion door closer when hold-open is not engaged or current is interrupted with Swing-Free arm engaged. Handed for right or left swinging door. Concealed or exposed electrical connections. Built-in “On/Off” switch controls hold-open function. Swing-Free arm allows door to be moved without door closer resistance. Interfaces with fire alarm systems. LCN Sentronic Door Closer 4310ME part are also available.
4310ME-