Search results for: 'cal rated door close arm bushing'
-
Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3- -
Von Duprin 2670 Guard-X Panic Device
Heavy Duty Design
The new Series 2670 Exit Alarm Lock provides secure protection through a large stainless steel deadbolt, which is 2" x 1/2" (51mm x 13mm) and has over a 3/4" (19mm) throw. The engagement area into the strike is over 1 1/4" (32mm) square inches. The cast aluminum latch case protects the internal mechanism and resists tampering or vandalism from inside the door. This unit has been tested to withstand up to 1600 pounds of static load force against the door.Fits 36" to 48" doors.
Uses 9 volt battery
Ships with all mounting hardware and strike.2670EO- -
Detex ECL-230X Alarmed Deadbolt Panic Hardware-Single Point
The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm. The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.
ECL-230 -
LCN 4811 Auto Equalizer Door Closer
LCN 4810 Door Closer Pneumatically Operated
The 4810 AUTO EQUALIZER is LCN’s pneumatically powered MULTI-DOOR solution. This low-energy automatic operator provides easy access for people with disabilities, or the elderly. Designed primarily for manual opening applications that occasionally require automatic opening.4811- -
LCN 4822 Auto Equalizer Door Closer
LCN 4820 Door Closer Pneumatically Operated
The 4820 AUTO EQUALIZER is LCN’s pneumatically powered MULTI-DOOR solution. This low-energy automatic operator provides easy access for people with disabilities, or the elderly. Designed primarily for manual opening applications that occasionally require automatic opening.4820- -
Glynn-Johnson Overhead Door Holder 81 Series Surface Mounted
The Glynn-Johnson 81 Series Overhead Door Holder Surface Mounted provide rugged, heavy-duty door control. The jointed-arm design provides the most effective stop mechanism available. The shock absorber bracket is surface mounted, usually with sex bolts. The jamb bracket is mounted to the stop of the frame, so a minimum of door and frame preparation is required.
GJ80 -
SEM-7800-825 Armature for LCN Electro Magnetic Door Holder
The SEM-7800-825 Armature for LCN Electro Magnetic Door Holder is the door mounted piece for th LCN SEM7820-825 / SEM7830-825 / SEM7840-825 / SEM7870-825 series. It features a metal die cast construction armature. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". Available in an aluminum or dark bronze color. LCN Part # SEM7820-825, SEM7830-825, SEM7840-825, and SEM7870-825
SEM7820-825- -
Von Duprin 88 Tube Attaching Ring 090021
The Von Duprin 88 Tube Attaching Ring 090021 is also used on the Von Duprin 55. The ring fits over the device lever arm, and is expanded by the Wedge (88R90) and the Wedge Tite Screw (88R100). When the Wedge Tite Screw is tightened the Ring expands and keeps the crossbar parallel to the door. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110 -
LCN Door Closer Cover
The LCN Door Closer Cover is the standard plastic cover that ships with LCN Door Closers. Specify your current closers model number when ordering. Not all of the LCN closers have the same shape cover on the door closer cylinder. The part number is the Series Number followed by -72. So, the part number would be 1460-72, 4010-72, 4020-742, 4030-72, 4040-72 and 4110-72. We have access to all the covers, if yours is not here call us and we will quote you a price.
4XXX-72 -
LCN 1450 Rw/PA Door Closer-New
This new LCN 1450 Rw/PA Door Closer is a direct replacement for the Norton 8000,Yale 3000, and Falcon/Dor-o-Matic SC80 Series Door Closers, or any door closer that has the 3/4" x 12" hole spacing. It features, a cast aluminum cylinder, 25 year warranty, powder coated finishes, and stick on mounting template. This door closer comes with the ability to mount on the push, pull or top jamb and is non handed. The door closer meets Grade 1-ANSI A156.4, UL/cUL, ADA and the Buy American Act certifications.
Hole Spacing 3/4” x 12”
1450- -
Door Pull Handle 11
The Door Pull Handle 11 has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.
GHE11- -
Norton Traditional Door Closer 78 B/D
The Norton Traditional Door Closer 78 B/D is a door closer used in historic buildings. This is a replica of the original cast iron door closer used from the 1920’s to 1960’s. The new version is made of a cast aluminum alloy material, and should only be used when you are trying to keep historic designations. The hole spacing on this closer is 1-3/8" x 4-1/4”.
78B/D -
Door Sweep 1" Long Rubber
The Door Sweep 1" Long Rubber has an over height of 1-7/8", with 1" of it being the gray rubber seal. The mounting rail is constructed of extruded aluminum and is available in aluminum or dark brown finishes. This sweep ships with screws.
International Part # IDC-97V
IDC97V- -
Dor-o-Matic 1690/1990 Top Rod Latch Assembly PB130
The Dor-o-Matic 1690/1990 Top Rod Latch Assembly PB130 is also used on the 1390, 1490 and 2390. This latch has been around since the 1970's, and is usually the issue if your bottom rod is dragging on the floor. Although we are calling it Dor-o-Matic, it is actually known as a Falcon SU Top Latch due to a name change 5 or 6 years ago. This latch rolls over when the device is pressed in and then locks in that position. When the door closes, the 'U" channel of the latch flips over to a vertical postion and drops the rods. This latch always uses the PB48 Strike, our part # G199034. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are basically the same device, with the same parts, just a different name plate. Falcon part # PB130 or 4270101806.
G199025 -
SEM7830 LCN Electro Magnetic Door Holder
The SEM7830 LCN Electro Magnetic Door Holder features a die cast metal housing that is surface wall mounted. Tri-voltage design works with 12, 24 or 120 volts, with 35 lbs. of holding force. The magnet housing measures 2-13/16" wide by 4-5/8" high. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". The total projection of both pieces is 4-1/8". Available in an aluminum or dark bronze color. Armature extensions are available, along with replacement covers, magnets, and armatures.
LCN Part # SEM7830
SEM7830- -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Sargent Lever Return Spring 97-0425
The Sargent Lever Return Spring 97-0425 is usually a green color, however we have seen them in blue and red. The red spring has the same dimensions as the green, but the loop on the coil side of the spring was closed. Sargent is using this spring as a replacement for all of those springs. If you have a Sargent Panic Hardware, and the lever is sagging, or just hanging, this is most likely the problem. The spring measures 2-1/8" long by roughly 3/8" diameter.
Sargent part # 97-0425
G970425 -
Floor Door Stop FS444
Floor Door Stop FS444
This door stop has been around a long time. We have been selling it for the past 35 years, and it is one of our best sellers year in and year out.
Features: Ideal for interior or exterior use. Cast brass construction. Accommodates door undercut up to 2-1/2". Non-marring rubber tip. Packed with expansion shield and lead shield. This Floor Mounted Door Stop is 3" high, and the base has a 2-1/2" diameter.
RB444HD- -
Floor Door Stop / Holder
The F20 or GJF20 was a mainstay of Glynn-Johnson for years. When the Glynn-Johnson door stop line merged with H.B. Ives it became the FS20. This door stop has been discontinued from Ives, but we have been able find a large stock. This Floor Mounted Door Stop also holds the door open, when in the latched position you can push the door and the holding latch will flip up and unlock thee holding clip. It is constructed of cast bronze or brass and then plated to your desired finish. This stop has a 2-1/2" long base that is 1-1/2" wide. The overall height is 3-1/8" with a 2-5/16" floor to rubber stop centerline. For use with door undercut up to 2-1/2".
GJF20- -
SEM7850 LCN Electro Magnetic Door Holder
The SEM7850 LCN Electro Magnetic Door Holder features a metal die cast housing that is surface wall mounted. Tri-voltage design works with 12, 24 or 120 volts, with 35 lbs. of holding force. The magnet housing measures 2-13/16" wide by 4-5/8" high. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". The total projection of both pieces is 3-5/8". Available in an aluminum or dark bronze color. Armature extensions are available, along with replacement covers, magnets, and armatures. Outlet box not included
LCN Part # SEM7850
SEM7850- -
SEM7820 LCN Electro Magnetic Door Holder
The SEM7820 LCN Electro Magnetic Door Holder features a metal die cast housing that is surface mounted on the floor. Tri-voltage design works with 12, 24 or 120 volts, with 35 lbs. of holding force. The magnet housing measures 5-1/8" long x 4-9/16" wide and 3-7/16" high. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". The total projection of both pieces is 6-3/4". Available in an aluminum or dark bronze color. Armature extensions are available, along with replacement covers, magnets, and armatures.
LCN Part # SEM7820
SEM7820- -
Falcon Automatic Opener 8242
The Falcon Automatic Opener 8242 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8242 is a non handed, surface mounted, 115 volt closer for a push side mounting. If your door is an inswinging door you would use the 8231. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8242- -
Falcon Automatic Opener 8231
The Falcon Automatic Opener 8231 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8231 is a non handed, surface mounted, 115 volt closer for a pull side mounting. If your door is an outswinging door you would use the 8242. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8231- -
LCN 1250 Rw/PA Door Closer-New
The LCN 1250 Rw/PA Door Closer is a direct replacement for the Norton 1600, Yale 50, Falcon/Dor-o-Matic SC60, LCN 1260 and International 8050 Series Door Closers. It is ideal for low frequency and low abusive traffic areas, such as store front doors and interior doors. It features, a cast aluminum cylinder, 15 year warranty, powder coated finishes, and stick on mounting template. This door closer comes with the ability to mount on the push, pull or top jamb and is non handed. The door closer meets Grade 1-ANSI A156.4, UL/cUL, ADA and the Buy American Act certifications.
Hole Spacing 3/4” x 9-16”1250- -
Floor Door Stop FS442
Floor Door Stop FS442
This Floor Mounted Door Stop used to go by the name Glynn Johnson GJFB19 or FB19. When Ingersoll Rand purchased H. B. Ives in the 1990's they brought it over under the Ives Floor Mounted Door Stop FS442. Features: Designed to blend well with all types of construction and provide a minimum of hindrance to cleaning efforts. Accommodates door undercut up to 2". Heavy-Duty cast brass or aluminum construction. Non-marring rubber bumper. This door stop has an overall height 2-7/8". Mounted shield and screws included.
GJFB19- -
LCN 4642 Auto Equalizer Low Energy Closer
LCN 4640 Low Energy Door Closer
The 4640 AUTO EQUALIZER is LCN’s SMART & RELIABLE electrically powered low-energy power operator. It provides easy access for people with disabilities, or the elderly. Designed primarily for manual opening applications that occasionally required automatic opening.
4642- -
Door Pull Offset 1" Diameter PH-4000
The Door Pull Offset 1" Diameter PH-4000 is usually used on aluminum frame glass doors. This handle offers three different mounting options, one is surface mounted, where the handle is mounted over a mounting stud and then you tighten the set screw to hold the handle in place. The second method is thru bolted, the bolt goes all the way thru the door. And the third is back to were you have two handles mounted back to back. This handle projects 3-1/4", has a 2-1/4" door clearance, comes in 9", 10" and 12" centers. One of the most popular handles we sell.
PH-4000- -
4" Kickdown Door Holder FS544
4" Kickdown Door Holder FS544
The H.B. Ives FS544 Kick Down Door Holder has been a staple in schools for many years due to its heavy duty construction and inexpensive price. This is one of our most popular Kickdown Door Holder/Stop for the past 35 years. It is constructed of durable cast iron, which has great strength characteristics. The shoe is made of a non-marring rubber, which is replaceable. The shoe is also held in place with a screw, which makes it a great option in schools and area of high vandalism. This holder will work on door to floor clearances of 2" or less. The hole spacing is 7/8" x 1-9/16".
Made by H.B. Ives
GJL444- -
Anodized Aluminum Neoprene Door Shoe
The Anodized Aluminum Neoprene Door Shoe is an aluminum U channel to mount on the bottom of doors. The channel is 1 inch deep with a 1/2 inch neoprene seal on the bottom. Fits over the bottom of 1-3/4 inch thick doors. Ships in 36 or 48 inch lengths and comes with #6 x 3/4 inch stainless steel screws.
G15NA- -
Dorma 7414 Door Closer
Dorma 7414 Door Closer
The Dorma 7414 Series door closer features back check and adjustable spring sizing and is the ideal solution in a wide variety of applications, including barrier-free. This Grade 1 hydraulic surface door closer is both flexible and easy to install. The 7414 Series offers a compact design and is available in a variety of sprayed finishes to complement any opening’s decor.
Dorma part # 7414ARP689
3/4" X 10-1/4" Hole Spacing
7414- -
Door Pull Handle 10
The Door Pull Handle 10 has 5-1/2" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 6-1/4". The projection is 2" and the clearance is 1-1/2". Also known as a Door Handle or Door Grip. This handle ships with thru bolts and finish washers.
GHE10-