Search results for: 'hous surface 4 1 2 door hinge self'
-
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Norton Door Closer 7700 Series Power Track Arm
Norton 7700 Series Power Track Arm
Arm is shipped will all of the necessary hardware. This assembly includes the 7701ST-1AT Adjusting Head and Tube Assembly, and the 7701ST-1AR Adjusting Rod Assembly. The square shaft measures 7/16" x 7/16". The aluminum finish ships within 24 hours, dark bronze will take a little longer.
Norton Part # 7701ST-1A
7701ST1A-Von Duprin Thumb Piece 970488
The Von Duprin Thumb Piece 970488 is just the thumb piece only, rivet not included. Cast bronze construction, and then plated to the selected finish. 5-1/8" overall length, but note that the length is usually cut down in the field depending on the thickness of your door.
Von Duprin Part # 970488
Old Part # 960303G970488-Von Duprin 6114 24VDC Electric Strike
Von Duprin 6114 24VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The 6114 has a 3/4” latch bolt throw, 7” face plate length, 1-7/8” width, and projects1-9/16”. The lock retrofits the Folger Adams FD 310-5. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6114Brushed Stainless Steel Door Kick Plate 18 Gauge .037
The Brushed Stainless Steel Door Kick Plate 18 Gauge .037 is the lightest duty stainless steel plate we offer . Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. This plate is ideal as a replacement for Brushed Chrome kick plates. Brushed Chrome Kick Plates are usually a bronze plate that is chrome plated. The problem with bronze is it is a soft metal and dents easily. The stainless steel plates are a lot harder and more resistant to dents. Brushed chrome looks identical to brushed stainless steel. We only use type 304 stainless.
Stainless Steel Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.22 per square inch depending quantity
Please allow 1 week shipping time
GKP-ss-18gaVon Duprin 99 Push Bar Retrofit Kit-Pbkit
The Von Duprin 99 Push Bar Retrofit Kit-Pbkit updates your current version touch pad, to the newest version. Used on all the Von Duprin 33A, 35A, 99 and 98's. For doors 30" to 36" order the 36" size. If your door is 36" to 48" order the 48" size. The Push Bar is 18" wide on the 36" version. Please allow 1 week for delivery.
Von Duprin part # PBKIT
G99R35Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50-Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040Detex ECL-230D-PH Alarmed Panic Device
The Detex ECL-230D-PH Alarmed Exit Device is a battery operated, rugged deadbolt panic device, and is UL-Listed Panic Hardware for 36" to 48" doors. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force, and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
ECL230DPH-Von Duprin 050814 Solenoid Kit for E996
The Von Duprin 050671 and 050814 solenoid have been discontinued. All of our stock is gone. Von Duprin has come out with a retrofit kit to update your E996 Lever to the M996 Lever. The kit changes out the solenoid for a mortorized version, more robust and uses less current. The newer version can be found by searching for M996.
This solenoid is used on the E996 Electrified Lever Trim. The Solenoid body measures 1-3/8” x 9/16” diameter, mounting bracket has a 3/4” on center hole spacing. The wiring harness has a two wire plug. We some times fine the number 991342 on the solenoid.
New for 2024 Von Duprin has come up with a Mechanical Electrified Conversion kit. This kit converts the EL Solenoid to a Mechanical Electrified Trim. More information can be found @ https://www.robertbrooke.com/von-duprin-m996l-retrofit-kit.html
Von Duprin Part # 050814
Von Duprin Part # 050671G050814Detex ECL-230D Alarmed Panic Device
The Detex ECL-230D Alarmed Exit Device is a battery operated, rugged deadbolt panic device. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
If you have a door that requires Panic Hardware, then use the ECL-230D-PH
ECL230D-Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft
The Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft is the piece that your dog key (allen wrench) fits into the lock the device in the open or dogged position. This shaft is used on the 1690, 1790, and 2390 device. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are basically the same device, with the same parts, just a different name plate. The part that the hex key fits into is only about 1/4" deep, because of that these tend to get rounded out, so the key will not move the shaft.
To remove the old shaft just pull with a pair of Channel Locks or Pliers. To reinstall, just press it back in to position, you might have to bend the holding tabs back down, but we very rarely have to do this. The manufacture part number on this is SHAFT.101.
GPBX16-SHFAnodized Black Aluminum Door Kick Plate 315AN
The Anodized Black Aluminum Door Kick Plate 315AN are a flat black and match the black color we find on Storefront doors. These plates have an aluminum base metal, which is 18 gauge (.040") thick that is then Anodized in the Black Color. These plates relatively inexpensive. Custom sizes are available, they run about $0.25 per square inch.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
GKP-BLKDetex ECL-230X Alarmed Deadbolt Panic Hardware-Single Point
The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm. The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.
ECL-230Clear Plastic Door Kick Plates
The Clear Plastic Door Kick Plates are constructed of .125" thick acrylic. We recommend screw mounting on these plate, because you can see right through them, and would be able to see the Tape Mount or Glue. We have the more common sizes listed, but If you need a custom size they run about $0.22 per square inch.
GKP-CPCal-Royal 9000 Series Lever Trim HDESC
Cal-Royal 9000 Series Lever Trim HDESC is for use on the 9800 and 9800 Exit Devices. The Trim has a clutch mechanism to prevent breaking and two heavy duty springs to prevent sagging. Escutcheon measures 2-5/8 inches wide by 10-5/8 inches long. The lever projects out 2-7/8 inches. Key locks or unlocks lever.
HDESC-Von Duprin PS-902 Power Supply
The Von Dupin PS902 is used to supply power to their MEL Exits, along with the Dor-O-Matic, Falcon and Monarch MEL Exits. Standard features are UL294 Listed for Access Control, Class 2 Rated Power Input, Regulated and filtered DC Outputs. The PS902 is a 2A @ 12 or 24 VDC. We ship the PS902-2RS, which has 2 Relay board output.
PS902-2RS
