Search results for: 'rollers+for+sizing+door+bottom'
- Did you mean
- roller for sizing door bottom 0
- rolls for sizing door bottom 0
- rollers for spring door bottom 0
-
Falcon 299 Strike
Falcon 299 Strike
The Falcon 299 Strike is used on the 25-R and 24-R Devices. The 299 strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". This strike is the same as the Von Duprin 299 Strike.
Ships with shim and mounting screws
Falcon Part # 299
Fa299 -
Sargent Door Closer 351
The Sargent Door Closer 351 is the most heavy duty closer made by Sargent. This closers meets ADA requirements, meets the Buy American Act, and is certified Grade 1, the heaviest rating possible. The closer has the capability to be mounted on the push, pull or top jamb, and is non handed. It ships with arm, plastic cover, parallel arm bracket and all of the fasteners. The hole spacing is 2-1/2" x 9"
350- -
LCN Door Closer 4111 FL
The LCN Door Closer 4111 FL is known as the Smoothee, and is one of the heaviest duty door closers made, the FL stands for Fusible Link. The Fusible Link is a lead clip that melts at roughly 115 degrees, and releases the door so it can close and contain a fire. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 FL model, which is a hold open fusible lind, on this page. The cylinder mounting holes are 2-1/2" by 6".
4110FL -
International 300 Series Adjustable Power Door Closer
The International 300 Series Adjustable Power Door Closer is one of there new closers to meet ADA requirements. With this door closer you can adjust the spring tension, closing and latching speed, even after it was installed. The Spring Power is adjustable all the way down to 8-1/2 pounds of resistance, making it ideal for areas with the elderly and children.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
Finger Protector For Doors - Interior Push Side
Door Finger Protector - Interior Push Side
These patented door guards fold against the jamb, allowing them to swing completely 180 degrees. The guard is attached to the face of the door and frame with the provided strong adhesive tape. Clear-frosted color to compliment any color scheme. Finger-Gard for use on Interior Doors, on the push side. Available in 54" or 78" lengths
GFG-A -
4" Kickdown Door Holder Grand Standard
4" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.
GJ604- -
Norton 9300 Door Closer-Discontinued
Norton Door Closer 9300
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- Friction hold open arm optional
- UL listed and compliant with UL10C for positive pressure
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" Hole Spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
9300- -
5" Kickdown Door Holder Grand Standard
5" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.
made by Grand Specialties 605z 605b
GJ605- -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
Cal Royal 4400 Rim Panic Device
The Cal Royal 4400 Rim Exit Device has a Grade 2 rating. The device features a 3/4" Latchbolt, Roller Strike and a 1" diameter Crossbar. The device comes in a brushed chrome and dark bronze finish, and comes with either a 36" or 48" crossbar. You would need a 4-1/2" minimum stile width.
CR4400- -
Dorma 8831 Top Arm | For use with RTS88
The Dorma 8831 Top Arm for RTS88 is for use on Single and Double Acting doors. This arm is known as a side load arm, and usually has a notch in the door at the top to access the arm fastening block. This piece measures 10-1/2" long by 1-3/8" wide at the widest part, and is 1/2" thick. This is the standard arm in the RST01 and RST02 Packages.
Dorma Part # 8831
G8831 -
Detex EAX-300W Weatherized Battery Powered Door Prop Alarm
Detex EAX-300W Weatherized Battery Powered Door Prop Alarm
The Detex EAX-300W Series is designed for applications where doors may be used for egress or ingress, but may not be held or propped open. Door open times from 1 second to 4 minutes (15 second default) are field selectable. The smaller size makes installation quick and easy. The Weatherized version is designed for doors that open to the outdoors or environments.
Cylinder not included!
Uses a standard 9 volt batteryEAX300W- -
Dorma 8812 Offset Slide Arm for RTS88
The Dorma 8812 Offset Slide Arm for RTS88 is used on in the RST31, RST30, RTS29, RST28, RST27, RTS26 and RTS25 packages. This arm is used on Single Acting Doors. The track measures 13" long by 1-3/16" wide by 7/16" thick. This is the arm you probably have if you are using 3/4" offset hinges or 4-1/2" wide butt hinges.
Dorma Part # 8812
G8812 -
10" Kickdown Door Holder Grand Standard
10" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 9-3/8" to the Floor when mounted.
Made by Grand Specialties 610z
GJ610 -
Von Duprin 050135 Top Fitting and Cover for 5654 / 5754
The Von Duprin 050135 Top Fitting and Cover is for use on there 5654 / 5754 Mullions. Package includes the Top Fitting and Cover, and all of the fasteners. The Fitting measures approximately 11/16" wide on face closest to the door and 2-3/8" at the widest point. The depth is 3-1/8"
Von Duprin Part # 050135
G050135- -
Sargent 281 Door Closer
The Sargent 281 Door Closer is also known as the Powerglide, This closers meets ADA requirements, meets the Buy American Act, and is certified Grade 1, the heaviest rating possible. The closer has the capability to be mounted on the push, pull or top jamb, and is non handed. This closer is the replacement for the 1250 and 1251 series closers. This closer has been the replacement for the 1250 since about 2000. It is manufactured of an aluminum alloy.
Replaces the older Sargent 1250 and 1251 door closers, mounting holes will match
281- -
Cal Royal Products 400 Series Door Closer | Economical Door Closer
The Cal Royal Products 400 Series Door Closer is for lighter use interior doors. This closer is considered a Grade 2, which means it is only rated for 1,000,000 cycles. The 400 Series is a sized closer, meaning you can not adjust the spring tension, the spring size you select is what you get. Also, make sure to note the hole spacing of the various sizes below. These closers also offer adjustable closing and latching speeds.
Size 420 3/4" x 6-5/8" hole spacing
Size SM 430P 3/4" x 6-1/2" hole spacing
Size 430P 3/4" x 8-3/16" hole spacing
Size 440P 3/4" x 8-3/16" hole spacingCal Royal 400 Series Catalogue
400P -
Norton Door Closer 1601BF Barrier Free
The Norton Door Closer 1601BF Barrier Free has been around for about 10 years. With the advent of aluminum framed glass doors, Norton was one of the first manufactures to come up with a narrow stile door closer. Because of this, it is still one of the most popular door closer models out there. It is a Grade 1 closer and has adjustable closing, latching, and back check speeds. The Barrier Free version just means you can turn the spring tension down to a size 1 spring, which will meet the ADA codes (less than 5 pounds of resistance). The model we ship also has adjustable spring tension to work on a wider range of doors. The hole spacing is 3/4” x 9-1/16”.
1600BF- -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606- -
Sargent Door Closer 1431
The Sargent Door Closer 1431 is also known as the Powerglide. This closer meets ADA requirements and has a capability to be mounted on the push, pull or top jamb, and is non handed. This closer can be used as a direct replacement for the older version 1230 or 1231 Sargent Closers without having to re drill the mounting holes. This closer has been the replacement for the 1230 since about 2000. It is manufactured of an aluminum alloy.
Retrofits existing SARGENT 1230/1231 Series Closer installations
1430- -
Von Duprin 4954 7' 6" Steel Mullion
The Von Duprin 4954 7' 6" Steel Mullion is the standard mullion used on most double doors with the Von Duprin Exit Devices. Mullions are easily removed by loosening bottom set screw and removing top fitting cover. The steel mullions are 2" wide and 3" deep, with an 1/8" thickness construction. We ship the 7'6" mullion, if you need the 8'6" or 10'6", please call. Package includes the 050390 and 050335 top and bottom brackets.
4954- -
Crash Chain Door Stop CS115
Crash Chain Door Stop CS115
- Specially designed for full-size exterior doors.
- Tear resistant, grey vinyl cover.
- Heavy duty compression spring assembled to both ends of chain
and end brackets. - Packed with sheet metal screws.
- Cast Brass brackets with solid, welded steel chain.
Available in 20-1/2", 25-1/2" and 30-1/2" lengths. Length is determined
by the location of your door closerPART # LENGTH
GCC205 20-1/2"
GCC255 25-1/2"
GCC305 30-1/2"GCC205- -
Sargent 8700 Panic Device
For Doors Wood or metal. 1-3/4" (44 mm) thick standard.
minimum stile with trim and 3-1/2"
Mounting Supplied standard with wood and machine screws
Chassis Cover Cold drawn brass, bronze or stainless steel
Chassis Nonferrous alloy
Hand Handed. Specify RHRB or LHRB
Dogging Feature Allen-type dogging furnished standard.
Top and Bottom Bolts Brass, stainless steel8700EO -
LCN Sentronic Door Closer 4414ME
LCN Sentronic Door Closer 4414ME
Standard LCN Sentronic Door Closer 4410ME series closer shipped with a 24V or 120V cylinder (please specify) on a mounting plate, metal cover, regular arm, and wood and machine screw pack. Sized cylinders for interior doors to 4’0”. Functions as full rack and pinion door closer when hold-open is not engaged or current is interrupted. Handed for right or left swinging door. Concealed or exposed electrical connections. Built-in “On/Off” switch controls hold-open function. Interfaces with fire alarm systems.
LCN SENTRONIC DOOR CLOSER 4410ME parts are also available.
4410ME -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Detex EAX-500 Battery Powered Door Exit Alarm
Detex EAX-500 Battery Powered Door Exit Alarm
The Detex EAX-500 Series is designed for applications requiring a battery-powered alarm on secured doors. The alarm, with approximately 100dB, will sound when an unauthorized exit occurs. The redesigned shape and smaller size of the EAX-500 makes it the ideal choice for quick and easy installations on emergency exit and restricted doors.
Mortise cylinder sold separately
Uses a standard 9 volt batteryEAX500- -
Lifetime Polished Brass Door Kick Plate
The Lifetime Polished Brass Door Kick Plate has a 16 gauge (.050″ thick) base metal, that is then plated with a artificial brass finish that is then polished. The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD. Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish. The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates.
Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″. You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes, but they are made of Stainless Steel, which is a tough metal to drill. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.40 per square inch depending quantityPlease allow 1 week shipping time
GKP-US3-PVD -
Dorma 8835 Top Arm for RTS88
The Dorma 8835 Top Arm for RTS88 is for use on Double or Single Acting doors that have a 1" top rail. This arm is used on aluminum framed glass storefront doors. The arm is 10-7/8" long and 1-3/8" wide. The spindle lug 1" thick. This is the standard arm on the RST07 and RST10 packages.
Dorma Part # 8835
G8835 -
International Door Closer 8630S SVR Device-Grade 1
International 8630S Surface Vertical Rod Device-Grade 1
DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.
Non handed, 4-1/2" minimum stile width. Smooth Surface.
For doors 29" to 36" wide order the Size 30 to 36"
For doors 36" to 48" wide order the Size 48"8630S- -
Door Sweep 1-9/16" Long Brush
The Door Sweep 1-9/16" Long Brush is one of the longest brush sweeps we offer. The brush is 1-9/16" long, with the mounting strip being 1-3/16". The mounting strip is constructed of extruded aluminum, and the holes are slotted for adjustment. The mounting screws, which are #6 x 3/4" stainless steel sheet metal screws are included. This product is easily cut down in the field.
E609A -
Brushed Stainless Steel Door Kick Plate 18 Gauge .037
The Brushed Stainless Steel Door Kick Plate 18 Gauge .037 is the lightest duty stainless steel plate we offer . Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. This plate is ideal as a replacement for Brushed Chrome kick plates. Brushed Chrome Kick Plates are usually a bronze plate that is chrome plated. The problem with bronze is it is a soft metal and dents easily. The stainless steel plates are a lot harder and more resistant to dents. Brushed chrome looks identical to brushed stainless steel. We only use type 304 stainless.
Stainless Steel Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.22 per square inch depending quantity
Please allow 1 week shipping time
GKP-ss-18ga -
Yale 2300 Door Closer-Discontinued
Yale 2300 Door Closer
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" hole spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
2300-