Search results for: 'style caps push plate'
-
Von Duprin 050536 HD-EL Solenoid
Von Duprin 050536 HD-EL Solenoid
Electric Latch Retraction for Von Duprin Exit Devices with Hex Key Dogging. #4 on the diagram below large picture.
Von Duprin part # 050536
Old Part # was 110740No longer available, the only solution we have at this time is to upgrade to the HD-QEL Base Plate.
G050536 -
Von Duprin Strike 385A
The Von Duprin Strike 385A is used on the floor for the Von Duprin 2227, 8827, 9827 and 9927 Surface Vertical Rods. Von Duprin recommends this strike if you are mounting the bottom strike in wood. The strike face plate outside dimensions are 2-1/4" x 2-1/4" with an inside dimension of 1-1/8" by 1". This floor strike features a bolt that can be cemented into the floor. This is an optional strike when added security is needed. Zinc plated finish.
385A -
Corbin Russwin Regular Arm Parallel Bracket
The Corbin Russwin Regular Arm Parallel Bracket is the standard bracket shipped by them for the past 40 years. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket is required if your are going to use a parallel arm mounting, which is when you have the closer mounted on the door, on the push side of the door. Corbin Russwin part # 188F41-8.
2800PA- -
LCN Door Closer Rod And Shoe
The LCN 79 Door Closer Rod And Shoe piece fits into the female part of all LCN Regular Arms. The old style had two concave set screws and a ball pressed into the rod. If the door over rotated the ball would pull out of the concave set screws. The new version has a pin holding the rod to the shoe which is designed to fail if the door is over rotated. This piece will work on the LCN 1260, 1460, 4010, 4020, 4030 and 4040 door closers with regular arms. Some of the really old models have multiple threaded holes, so you might have to drill a hole in the female tube. Part #'s 4040-79, 4040-79LR and 4040-79ELR. The 1260, 1460, 4010, or 4020 could replace the 4040 in those part numbers, they are the same.
79 -
Detex D Lever Trim for 10 Series
The Detex D Lever Trim is used on the 10, 20, 21 and 27 Series exit devices. The D Lever is designed to be as heavy duty as their exit devices. It features a break-away lever to prevent damage. The escutcheon measures 2-3/4 x 9-1/16 inches, with a plate thickness of 7/8 inch. We ship the classroom function, which locks and unlocks the lever.
G08DS- -
LCN 4410HSA Sentronic
The 4412HSA SENTRONIC® is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Double lever arm closer is specifically designed for push side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.
4410HSA -
International Door Closer 853P Series
The International Door Closer 853P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and whether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 32” interior or 28” exterior doors.
Direct replacement for the older style Norton 1602 and 1603, and Yale 52 and 53, that had the 3/4" x 8-3/16" mounting holes
853- -
Handicap Saddle Threshold 424 - 4" Wide By 1/2" High
Saddle Threshold 424 - 4" Wide By 1/2" High
Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.
Other sizes and finishes are available, call for more information.
Air shipment is not available on this product. Please allow 7-10 days for delivery.
424- -
Falcon Automatic Opener 8242
The Falcon Automatic Opener 8242 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8242 is a non handed, surface mounted, 115 volt closer for a push side mounting. If your door is an inswinging door you would use the 8231. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8242- -
Falcon SC71 Door Closer
The Falcon SC71 Door Closer used to go by the Doromatic SC71. This is a higher quality door closer at a more affordable price. This closer offers adjustable closing, latching and back check speeds, along with adjustable spring tension. It has the ability to be mounted on the push, pull or top jamb and is non handed. This closer is considered a Grade 1 closer, which is the highest grade you can get. The hole spacing is 2-3/8” x 6-3/4”, which is the same hole spacing as the Norton 7500 and Yale 4400 door closers. We ship the SC71 Rw/PA
SC70- -
Dust Proof Strike DP2
• Designed for use with the bottom bolt of all flush bolts.
• Spring-loaded plunger returns to floor or threshold level anytime
flush bolt is retracted, eliminating need to clean standard
floor strikes.
• Strike hole is 3/4" Diameter and 1-1/8" Deep
DP2 Face Plate: 1-5/8" W x 3-1/2" L x 1/8" Thick
Body: 1-3/16" Diameter x 1-7/8" DeepDP2- -
Handicap Saddle Threshold 613 - 6" Wide By 1/4" High
Saddle Threshold 613 - 6" Wide By 1/4" High
Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.
Other sizes and finishes are available, call for more information.
Air shipment is not available on this product. Please allow 7-10 days for delivery.
613- -
Plunger Door Holder / Stop FS1153
The Ives Plunger Door Holder / Stop FS1153 is manufactured by H.B. Ives and features a contemporary yet economical method of positive Hold-Open. This was another one of the Glynn-Johnson door stops that was merged in the H.B. Iver product line in the 1990's, and went by the 1153 part number. This door stop is constructed in sturdy cast aluminum for years of service. The spring operated plunger activates with minimal pressure, releasing instantly with a light tap on the plat-form lever. The stop has a 1-5/8" throw or projection for all types of doors. The ribbed non-marring rubber shoe is securely fastened to unit with a screw and is easily replaced when worn. These are sometimes called pop-up or push down stops. Ships with mounting screws.
Aluminum finish only
GJ1153M -
Global Door Controls TC201 Door Closer
The Global Door Closer TC200 is recommended for use on all aluminum store front doors, wood or hollow metal commercial applications. It is a versatile utility closer that provides narrow styling and has a full selection of accessories to accomodate the requirement of any field installation.
In this series, our Global Door Closer TC201 is a multi-size spring model that offers adjustable power with a choice of range sizes 2-5 where high rates of closing force are required. Our TC201ADA model also offers adjustable spring power sizes 1-4 for use on interior doors requireing less than 5 lbs. of opening force and exterior doors requiring less than 8.5 lbs. This complies with ADA handicap codes and ANSI/BHMA standard requirements. Both models will retrofit most full size closers with a 9 1/16" industry standard hole patten to update any opening for code compliance.
Hole Spacing is 3/4" x 9-1/16"
Options: Specify when ordering:
- Finish - AL, DU
- Size 1-4 or 3-6
TC201-- -
Von Duprin Thumb Piece 970488
The Von Duprin Thumb Piece 970488 is just the thumb piece only, rivet not included. Cast bronze construction, and then plated to the selected finish. 5-1/8" overall length, but note that the length is usually cut down in the field depending on the thickness of your door.
Von Duprin Part # 970488
Old Part # 960303G970488- -
International 5000 Series 58L Escutcheon Trim
International 58L Escutcheon Trim for the 5000 Series Devices
Non-handed, easily install with exit device Escutcheon plate measures 8-1/16" tall by 2-5/8" wide by 29/32" thick. We offer 3 functions, Classroom, Passage and Storeroom.
Classroom - cylinder (not included) locks and unlocks lever handle-Most Popular
Passage - no cylinder hole, lever always active
Night Latch (Storeroom) - cylinder (not included) unlocks lever, but lever is always locked when key is removed.58L01- -
Dor-o-Matic 1990/2090 "E" Ring RRing.109
The Dor-o-Matic 1990/2090 "E" Ring RRing.109 is use to connect the concealed rods to the Traveller Assembly (G199028, PB88, or 4270100013). The rods fit through the traveller and rod bushings, and the Retaining Ring holds them in place. This piece has a diameter of 1/2". This item is now under the Falcon name plate.
Dor-o-Matic 990/1990 Repair Parts Breakdown
Dor-o-Matic 1690 Repair Parts BreakdownG199004 -
SEM7840-516 LCN Magnet Core Assembly
The SEM7840-516 LCN Magnet Core Assembly is just the Tri Voltage Magnet Core. 35 pounds of holding force at nominal input voltage. Maximum current draw is .020 A @ 24 volt and 120 volt, and .030 A @ 12VDC. Cylinder is 1-3/4" diameter and projects out 7/8" out from the mounting plate.
LCN part number SEM7840-516
SEM7840-516 -
Handicap Saddle Threshold 413 - 4" Wide By 1/4" High
Saddle Threshold 413 - 4" Wide By 1/4" High
Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.
Other sizes and finishes are available, call for more information.
Air shipment is not available on this product. Please allow 7-10 days for delivery.
413- -
Falcon 650387 Bottom Bolt Guide Assembly
Falcon 650387 Bottom Bolt Guide Assembly
The Falcon Monarch Bottom Bolt Guide Assembly 650387 is used the 19-V, 24-V, 25-V and the XX-V Bottom Rod. The Guide Assembly measures 1-7/8" tall by 1" wide and projects 1-9/16" at the widest projection. The Bottom Bolt Guide is made of zinc plated steel.
Falcon Monrarch Part # 650387
G650387 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Sargent Door Closer 1431
The Sargent Door Closer 1431 is also known as the Powerglide. This closer meets ADA requirements and has a capability to be mounted on the push, pull or top jamb, and is non handed. This closer can be used as a direct replacement for the older version 1230 or 1231 Sargent Closers without having to re drill the mounting holes. This closer has been the replacement for the 1230 since about 2000. It is manufactured of an aluminum alloy.
Retrofits existing SARGENT 1230/1231 Series Closer installations
1430- -
Handicap Saddle Threshold 513 - 5" Wide By 1/4" High
Saddle Threshold 513 - 5" Wide By 1/4" High
Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.
Other sizes and finishes are available, call for more information.
Air shipment is not available on this product. Please allow 7-10 days for delivery.
513- -
International Door Closer 852P Series
The International Door Closer 852P Series is common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 32” interior or 28” exterior doors.
3/4" x 7-3/8" mounting holes
852- -
Monarch 912L Panic Device Lever Trim
Monarch 912L Panic Device Lever Trim
The Monarch / Falcon 912L Lever Trim is for use on the Monarch / Falcon 19 Series. The 912L measures 7-1/4" high by 1-3/4" wide and the mounting plate is 5/8" thick. We ship these with the Dane Lever, which projects out 2-7/8" in the Classroom function. On the Classroom function the key locks and unlocks the lever handle, the Key Cylinder is not included. We offer this Lever Trim in Painted Aluminum, Painted Dark Bronze, and Brushed Satin Nickel.
Monarch Part # 912L Dane
G912L-