Search results for: '179l dogging panic door handle parts link'
-
LCN Door Closer 4111 FL
The LCN Door Closer 4111 FL is known as the Smoothee, and is one of the heaviest duty door closers made, the FL stands for Fusible Link. The Fusible Link is a lead clip that melts at roughly 115 degrees, and releases the door so it can close and contain a fire. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 FL model, which is a hold open fusible lind, on this page. The cylinder mounting holes are 2-1/2" by 6".

4110FL -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
LCN Door Closer Fusible Link Arm 3049FL
LCN Door Closer Fusible Link Arm
Adjustable nut allows door closer arm to lock when the preselect position is reached. Fusible Link will hold door until heat melts the "Link" and then the door will shut. Used on Fire Doors to control a spreading fire.
Specify your current closers model number when ordering.
Not all of the LCN closers have the same shape spindle on the door closer
cylinder. The LCN Part #'s on this Fusible Link Arm is: 4010-3049FL, 4020-3049FL, 4110-3049FL
3049FL -
LCN Door Closer 4011FL | LCN 4011 FL
The LCN Door Closer 4011FL is shipped with fusible link arm, standard plastic cover, and self reaming and tapping screws. Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder (4011) adjustable for interior doors to 4’6” and exterior doors to 3’6”. Included arm has a fusible link that melts at 120 degrees, allowing to door to close. Door can be closed any time with a gentle pull. Closer mounts hinge side, specify right or left swinging door. 4011 cylinder meets ADA requirements.
We ship the 4011 FL

4010FL- -
LCN Door Closer 4021 FL
The LCN Door Closer 4021 FL is shipped with fusible link arm, standard plastic cover, and self reaming and tapping screws. This closer is designed to hold open fire doors, when the fusible link melts, it releases the hold open arm, so the door will close. Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Included arm has a fusible link that melts at 120 degrees, allowing to door to close. Door can be closed any time with a gentle pull. Closer mounts top jamb (push side), specify right or left swinging door. 4021 cylinder meets ADA requirements.

4020FL -
Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117
The Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117 is a replacement for the Screw Driver Headed Dogging Pin. Now instead of using a screw driver you can use the handy thumb piece instead. The package comes with new set screw, spring, and of course the pin. Jackson part number 30-1117.
G108554TP -
Jackson Panic Device 2085 Dogging Assembly LH/RHRB
Jackson Exit Device 2085 Dogging Assembly LH/RHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2462
This spring would be for the Device on the Right, shown below.
G302462 -
Door Pull Handle 16
The Door Pull Handle 16 has an overall length of 7-1/2". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.
GHE16- -
Jackson Panic Device 2085 Dogging Assembly RH/LHRB
Jackson Exit Device 2085 Dogging Assembly RH/LHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2467
This spring would be for the Device on the Left, shown below.
G302467 -
Door Pull Handle 22
The Door Pull Handle 22 features an opened end and a closed end pull. This Door Pull is also known as a Door Handle or Door Grip. The dimensions are 14" overall length, 8" centers, with a 3/8" by 1-1/4" handle cross section. The mounting posts have a 1" diameter, and the handle projects out 1-7/8". The handle ships with thru bolts and finish washers. It is constructed of aluminum, stainless steel or brass depending on the finish you are looking for.
GHE22- -
Corbin Russwin 650F968 Cylinder Dogging Sub-Assembly
The Yale 7000 and Corbin Russwin ED4000/ED5000 Cylinder Dogging Sub Assembly is used on non Fire Rated Yale and Corbin Russwin panic devices. Like the Hex Key Sub Assembly, this one is for use with a Key Cylinder.
Yale Part # 60-7000-0407-999
Corbin Russwin Part # 650F968G6070000407 -
Sargent 20/30/60/80 Dogging Kit 68-2596
The Sargent 20/30/60/80 Dogging Kit 68-2596 is used on the Sargent 20, Sargent 30, Sargent 60, and Sargent 80 Series Panic Hardware. This dogging assembly kit has been around since the 1980's. We only sell the dogging assembly parts as a complete set.
Sargent part # 68-2596
G80200 -
Door Pull Handle 24
The Door Pull Handle 24 features a 6" center to center screw spacing. The handle is constructed of aluminum, stainless steel or brass depending on the desired finish. The handle is 1" solid diameter stock and the mounting posts are 3/4" diameter stock. It measures 8" overall length and projects from the door 2". It ships with thru bolts and finish washers. Also known as a Door Handle or Door Grip.
GHE24- -
Dor-o-Matic 2090 Latch Link PB62
Dor-o-matic 2090 latch link
Dor-o-Matic 1090/2090 Repair Parts Breakdown
G209040 -
Jackson Panic Device 1085 And 1095 Dogging Pin
The Jackson Panic Device 1085 And 1095 Dogging Pin is the piece that keeps the hardware in the open position during business hours. It is activated by pressing the crossbar and then turning the flat head screw driver head. The pin is held in the housings with a screw, which is located on the back of the housing. This pin has been used since about 1988 or so, the old style are no longer made, but they had a roll pin that was used to hold it in place. This package comes with a new spring, set screw and the pin. The Jackson part number on this is 30-1115.
G108554 -
Offset Pull Handles mounted Back to Back
The Door Pull Offset #39 Handle is constructed of either solid aluminum, brass or stainless steel. The handle is 1" diameter tubing with a 2-3/4" offset and 2-3/4" projection. This is the most common type of handle you use today. Just about every aluminum framed storefront door has a version of this handle. This handle is available in 8", 10", 12" and 18" centers on the mounting holes. The back to back mounting is for Metal or Wood Doors that are 1-3/4 thick. Included fastener is threaded into one of the handles, and the Stud End has fits into the inside handle and is held in place by a set screw on the handle.
Package includes two offset pull handles and fastening hardware. Shown in Polished Stainless Steel with 12 inch centers.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks.
GHE39x39 -
Monarch Dor-O-Matic Falcon 600339 NL Spring Package
The Monarch / Dor-O-Matic / Falcon 600339 NL Spring Package converts the 179L , 712L, 712K, 912l and 911K to an NL function. The NL function is one were the Lever Handle can not be unlocked and left in the unlocked position when the key is removed. Spring has a 5/8" diameter. See attached instructions.
G600339 -
Von Duprin Panic Device 8827 Center Case 050415
The Von Duprin Panic Device 8827 Center Case 050415 is for use on the non fire rated 88 surface vertical rod. You can tell the difference by the dogging screw. If you have a Dogging Screw on your device, then this is the correct part. Includes the internal pieces, including the Rod Control.
Von Duprin part # 050415
88VR120- -
Door Pull Handle 23
The Door Pull Handle 23 features two closed ends. This Door Pull is also known as a Door Handle or Door Grip. The dimensions are 14" overall length, 8" centers, with a 3/8" by 1-1/4" handle cross section. The mounting post has a 1" diameter, and the handle projects out 1-7/8". The handle ships with thru bolts and finish washers. It is constructed of aluminum, stainless steel or brass depending on the finish you are looking for.
GHE23- -
Door Pull Handle 11
The Door Pull Handle 11 has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.
GHE11- -
Back to Back Mounted Handle 1 Inch Diameter
Back to Back mounted 1 inch diameter stock. One handle will be threaded and the other will be a female fitting that snugs the handle with a set screw. The standard Stud that ships with the handle is for an 1-3/4 thick door.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GHE26x26 -
Door Pull Handle 10
The Door Pull Handle 10 has 5-1/2" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 6-1/4". The projection is 2" and the clearance is 1-1/2". Also known as a Door Handle or Door Grip. This handle ships with thru bolts and finish washers.
GHE10- -
Push Bar w/Handle 422X26
The Push Bar w/Handle 422X26 is usually found aluminum framed glass store front doors. It is constructed of 1" diameter solid aluminum, brass, bronze or stainless steel, depending on the finish. The handle or grip will have either a 8", 10", 12" or 18" center to center screw spacing. The push bar center to center length is determined by you, we can do any reasonable size. Establish the center to center dimension by subtracting the width of one stile from the width of the door. On solid doors, subtract 5" from the width of the door. All the fasteners are included, and are determined by the material your door is made of (wood or metal). Please allow 3-4 weeks on the Dark Bronze and Aluminum, and 2 weeks on the other finishes.
422x26









































