Door Closers
At RBA Door, we offer a wide range of high quality door closers, assemblies and accessories. Our door closers and door closing accessories are perfect for “high-traffic” commercial uses in schools, universities, churches, YMCA, offices, business, warehouses and exhibit halls. We also feature low-power door closers perfect for those with limited mobility. Our products are the ideal solution to maintain a first point of building security and to reduce energy consumption in climate controlled areas..
-
Norton Door Closer Arm Shoe Assembly
Norton / Yale Door Closer Arm Shoe Assembly
Replacement Shoe Assembly for Norton 1600, 9300, 7500 and 8000 series door closers. And Yale 50, 2300, 8000 and 4400 series.
Base measures 11/16" x 2-1/4" with 1-3/4" center to center screw hole mounting. Bracket projects out 15/16". The pin is 3/8" diameter.Norton part # 7701AS or a Yale # 400-AS
Old Norton Part # 1620AS
7701AS- -
Norton Door Closer 7701-13 Hold Open Loop Assembly
The Norton Door Closer 7701-13 Hold Open Loop Assembly is usually the part that breaks on the Norton 1600, 9300, 8301, 8501 and 7500 Hold Open Door Closers. The cast iron piece attached to the disk is where they usually break. This part has had a few part numbers over the years, for Norton it has been known as the 1620-13 and 7701-13, and for Yale the 400-13.
16H300- -
Norton 6870T-8 CloserPlus Hold Open Arm
Norton CloserPlus Hold Open Arm
This heavy duty Parellel Arm can be used with the Norton 1600, 9300, 8000 and 7500 door closers. The knob on the main are locks and unlocks the arm to hold your door open.
Aluminum is in stock, Dark Bronze is 2-3 week lead time.
Norton Part # 6870T-86870T-8- -
Norton Door Closer 7700 Series Power Track Arm
Norton 7700 Series Power Track Arm
Arm is shipped will all of the necessary hardware. This assembly includes the 7701ST-1AT Adjusting Head and Tube Assembly, and the 7701ST-1AR Adjusting Rod Assembly. The square shaft measures 7/16" x 7/16". The aluminum finish ships within 24 hours, dark bronze will take a little longer.
Norton Part # 7701ST-1A
7701ST1A- -
Norton 7705 PTO PowerTrack Only
The Norton PTO PowerTrack for 7705 is a replacement piece for the 7705PTO Door Closer. The Track includes the Slider, Soleniod and new mounting screws. The Track measures 21-1/4" long with a hole spacing of 19" on centers. The PTO Track is for the Pull Side of the door, also known as the Hinge Side because you can see the hinges on that side. On the PTO Track Assembly you can see the Two Mounting Holes
Norton Part # PTO24 or PTO120
PTO24-- -
Norton P7705 PPTO PowerTrack Only
The Norton PPTO PowerTrack for P7705 is a replacement piece for the P7705PTO Door Closer. The Track includes the Slider, Soleniod and new mounting screws. The PPTO Track is for the Push Side of the door, also known as the Stop Side because the track mounts on the jamb stop.
Norton Part # PPTO24 or PPTO120
PPTO24-- -
Norton Current Style Replacement Springs
Norton New Style Replacement Door Closer Springs
This is the replacement door closer spring for the Norton 78, and Yale 1900 Door Closers. Spring measures 2-11/16" diameter by 2" tall. This spring is identifiable by the number stamped on the band that holds the spring together. The band will be stamped either B/D 2/4, or E/F 5/6.
Norton 78 B/D and Yale 1902-4 use spring 24BD
Norton 78 E/F and Yale 1904-6 use spring 56EFNorton Part # 24BD
Norton Part # 24EF78xxSP -
Yale Replacement Covers
One of the problems out in industry today is vandalism. These Yale Replacement Covers will replace your existing cracked and broken covers. The covers are available for the 4400, 3300, and 3500 models. They are made of impact resistance plastic. The cover shown is for the 4400, in the aluminum finish.
yale-covers -
Jackson Door Closer Offset Arm - 20-900-LC
The Jackson Door Closer Offset Arm 20-900-LC is used with the 20-330 concealed closer for single acting offset mounted doors. The arm measures 12-15/16" long by 1/2" thick with a 1.012" offset. The track measures 25/32" deep by 29/32" wide by 14" long. The track includes the nylon slide, pin and retaining clips.
Jackson Part # 20-900-LC
G20900LC -
Jackson Door Closer Offset Arm 20-1134LC
The Jackson Door Closer Offset Arm 20-1134LC is the arm and track assembly for the 20-330 concealed closer. The arm measures 12-15/16" long with .919" offset, and the track measures 1/2" thick by 12-7/8" long by 1-9/32" wide. The track includes the nylon slide, pin and retaining ring.
Jackson part # 20-1134-LC
G201134LC -
Jackson Door Closer Offset Arm - 20-1312-LC
The Jackson Door Closer Offset Arm - 20-1312-LC is the replacement arm and track for the Jackson 20-330 Door Closer. The track measures 12-7/8" long by 1/2" thick, and the arm has an overall length of 12-15/16" long with an offset of .826". This set is for use with single acting doors with a 3/4" offset. Package includes the arm and track.
Jackson part # 20-1312-LC
G201312LC -
Falcon / Doromatic Door Closer 3049/PA Hold Open Arm Only
Doromatic Door Closer Hold Open Arm Only
Doromatic Door Closer Hold Open Arm. Includes everything is the image. Can be used to convert you regular non hold arm to a Hold Open Door Closer. Arm holds the door open when door is rotated open. The hold open postion is adjustable. This is the hold open arm for the SC61 Hw/PA, SC71 Hw/PA, and the SC81 Hw/PA.
Doromatic Part numbers:
SC60 - SC60-3049/PA , SC70 - SC70-3049/PA , SC80 - SC80-3049/PADo-3049 -
Corbin Russwin Door Closer Hold Open Arm
The Corbin Russwin Door Closer Hold Open Arm has been around for the past 40 years. This replacement hold open arm will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This is considered a Friction Hold Open Arm because as the arm rotates the arm tightens on itself and holds the arm in the open position. This arm is also known as the A1 arm. Corbin Russwin part # 688F77.
2800HOA -
Corbin Russwin Regular Arm for 2800
The Corbin Russwin Regular Arm for 2800 is the standard arm shipped by them for the past 40 years. This replacement regular arm will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. The arm is non handed and can be used for regular, parallel and top jamb mount. Corbin Russwin part # 688F95.
2800RA -
Corbin Russwin Regular Arm Parallel Bracket
The Corbin Russwin Regular Arm Parallel Bracket is the standard bracket shipped by them for the past 40 years. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket is required if your are going to use a parallel arm mounting, which is when you have the closer mounted on the door, on the push side of the door. Corbin Russwin part # 188F41-8.
2800PA -
Corbin Russwin Hold Open Arm Parallel Bracket
The Corbin Russwin Hold Open Arm Parallel Bracket is the standard bracket shipped with the Hold Open Arm. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket used by the hold open arm for parallel arm applications only. Corbin Russwin part # 509F49.
2800HPA -
Corbin Russwin 188F03 Quik-Install Mounting Bracket
The Corbin Russwin 188F03 Quik-Install Mounting Bracket is the standard bracket shipped by them for the past 40 years. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket is what you mount on the door or door frame and the door closer cylinder mounts to. Corbin Russwin part # 188F03.
Bracket size: 1-3/4" (44mm) (vertical) x 6" (152mm) (horizontal)
Hole spacing: 1" (25mm) (vertical) x 4-5/16" (110mm) (horizontal)G188F03 -
Sargent Door Closer Hold Open Arm 25-H
The Sargent Door Closer Hold Open Arm 25-H is known as a Friction Hold Open Arm. As the arm rotates it tightens the two plates together until they can not turn any more, and holding the door open. To close you just pull the door and it will "unscrew". The hold open position is adjustable by tightening or loosening the larger nut.
Sargent part # 25-H
350HOA- -
Sargent Parallel Arm Bracket 125-P
The Sargent Parallel Arm Bracket 125-P is for use with the 25-O regular arm, to convert it to a parallel arm mount. A parallel arm mount is when the door closer is mounted on the push side of the door and the arm is parallel to the door when in the closed position.
Sargent part # 125-P9
350PAB-