Door Closers
At RBA Door, we offer a wide range of high quality door closers, assemblies and accessories. Our door closers and door closing accessories are perfect for “high-traffic” commercial uses in schools, universities, churches, YMCA, offices, business, warehouses and exhibit halls. We also feature low-power door closers perfect for those with limited mobility. Our products are the ideal solution to maintain a first point of building security and to reduce energy consumption in climate controlled areas..
-
Norton 6870T-8 CloserPlus Hold Open Arm
Norton CloserPlus Hold Open Arm
This heavy duty Parellel Arm can be used with the Norton 1600, 9300, 8000 and 7500 door closers. The knob on the main are locks and unlocks the arm to hold your door open.
Aluminum is in stock, Dark Bronze is 2-3 week lead time.
Norton Part # 6870T-86870T-8- -
Norton Door Closer 7701-13 Hold Open Loop Assembly
The Norton Door Closer 7701-13 Hold Open Loop Assembly is usually the part that breaks on the Norton 1600, 9300, 8301, 8501 and 7500 Hold Open Door Closers. The cast iron piece attached to the disk is where they usually break. This part has had a few part numbers over the years, for Norton it has been known as the 1620-13 and 7701-13, and for Yale the 400-13.
16H300- -
Norton Door Closer Arm Shoe Assembly
Norton / Yale Door Closer Arm Shoe Assembly
Replacement Shoe Assembly for Norton 1600, 9300, 7500 and 8000 series door closers. And Yale 50, 2300, 8000 and 4400 series.
Base measures 11/16" x 2-1/4" with 1-3/4" center to center screw hole mounting. Bracket projects out 15/16". The pin is 3/8" diameter.Norton part # 7701AS or a Yale # 400-AS
Old Norton Part # 1620AS
7701AS- -
Norton / Yale Door Closer 7701-3 Hold Open Arm
The Norton / Yale Door Closer 7701-3 Hold Open Arm is the standard hold open arm shipped with Norton and Yale Door Closers. It is known as a Friction Hold Open, because as the arm rotates it tightens down two plates together. Adjusting the large hex bolt on the Hold Open Assembly determines where the arm will hold open. This part has had a couple of numbers over the years 7701-3, 1620-3 for Norton and 400-3 for Yale.
16H00- -
Norton Door Closer Parallel Arm Bracket
The Norton Door Closer Parallel Arm Bracket is the bracket shipped with the Norton 1600, 7500, 8301, 8501 and 9300 series closers. This bracket is also used by Yale on there 2300, 50, 3301, 3501 and 4400 door closers. The factory part number on this is 1618A for Norton and 289A for Yale.
1600PA- -
Norton Door Closer Regular Arm
The Norton Door Closer Regular Arm is the standard arm that is shipped with the 9300, 1600, 8301, 8501 and 7500 door closers. It will also work with the Yale 2300, 50, 3301, 3501 and 4400 series door closers. This arm has had a bunch of different factory numbers over the years, including 1620-1, 7701-1 and 400-1.
16000- -
International Door Closer Arm and Track 3020-VO
The International Door Closer Arm and Track 3020-VO is for offset top arm assemblies, with the track mortised in the top of the door. This track and arm are for the 7/8" depth of top rail application. Track measures 12-5/8" long by 1/2" high by 1-1/4" wide. For use with the 2000, 3000 and 5000 series concealed closers.
3010-VO -
International Door Closer 521 Regular Arm Forearm
The International Door Closer 521 Regular Arm Forearm measures 9-1/2" loop to loop in the shortest position, and 14" when it is the fully extended . The loop on the left side is 3/8" diameter. The hole spacing on the right hand side of the picture shoe is 1-3/4".
International part # 521
G521- -
International Door Closer Main Arm 520
The International Door Closer Main Arm 520 is a replacement arms used on the 640, 650, 850 and 880 series. This arm is probably used on other International Closers also. The arm measures 12" overall length, and fits a 7/16" square shaft.
International Door Closer part # 520
G520- -
LCN Door Closer Cover
The LCN Door Closer Cover is the standard plastic cover that ships with LCN Door Closers. Specify your current closers model number when ordering. Not all of the LCN closers have the same shape cover on the door closer cylinder. The part number is the Series Number followed by -72. So, the part number would be 1460-72, 4010-72, 4020-742, 4030-72, 4040-72 and 4110-72. We have access to all the covers, if yours is not here call us and we will quote you a price.
4XXX-72 -
LCN Door Closer Traditional Springs
Replacement springs for the older Pot Type Closers. You should find a number stamped on the end plug, which should relate to the "Size" below.
LCN Size B 1-5/16" high x 2-3/4" diameter-no longer available
LCN Size C 1-1/2" high x 3" diameter- No longer available
LCN Size D 1-11/16" high x 3-1/4" diameter - No longer available
LCN Size EF 2" high x 3-3/8" diameterLCNX -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
Rixson 27 Series Door Closer
• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustmentWhen Less All Parts is selected only the Cylinder is shipped, just the replacement hydraulic cylinder will be shipped
27-RIX -
Yale Door Closer 51 Series
The Yale Door Closer 51 Series has been around since the early 1970's. With the advent of the aluminum framed storefront doors, this door closer was a perfect fit. The 50 series is a non-sized, non-handed closer that can be mounted on the push (parallel arm), pull (regular arm) or top jamb. A Grade 1 closer certification, means it is one of the more heavy duty closers out there. Older models may be stamped with Scoville or Eaton, which are the companies that used to own Yale. We some times find 20-0054-4001 or 20-0254-4001 stamped on the back of the closer. Ships with all mounting screws and a parallel arm bracket. The hole spacing is 3/4" by 9-1/16".
50- -
Yale Door Closer 4400
The Yale Door Closer 4400 has been around for quite a long time, and was designed to replace the older 400, which are still made. The beauty of the 4400 is that is can be mounted left or right, push, pull or top jamb, were as the 4200 you had to specify all those attributes, which made stocking them a head ache. This is a Grade 1 closer, and is extremely durable. If you are looking for a 4400BF, the barrier free version, the new 4400 is barrier free, and will do the trick. This closer has a 2-3/8" x 6-3/4" hole spacing.
4400- -
Yale Door Closer 3501
The Yale Door Closer 3501 is constructed of a cast aluminum alloy. It is considered a Grade 1 Closer, which is the highest grade possible. The closer features an adjustable spring tension, and separate closing, latching and back check intensity valves. The full plastic cover is standard on this closer. This door closer replaces the older 3501BF closers. The new version is Barrier Free Complaint. The hole spacing is 3/4" x 12", the cylinder is sometimes cast 20-3301-1001 on the back of the cast aluminum cylinder. This closer ships with all of the mounting hardware and parallel arm bracket.
3500- -
Yale Door Closer 3301
The Yale Door Closer 3301 is constructed of a cast aluminum alloy. It is considered a Grade 1 Closer, which is the highest grade possible. The closer features an adjustable spring tension, and separate closing, latching and back check intensity valves. The slim line plastic cover is standard on this closer. This door closer replaces the older 3301BF closers. The new version is Barrier Free Complaint. The hole spacing is 3/4" x 12", the cylinder is sometimes cast 20-3301-1001 on the back of the cast aluminum cylinder. This closer ships with all of the mounting hardware and parallel arm bracket.
3300- -
Yale 2300 Door Closer-Discontinued
Yale 2300 Door Closer
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" hole spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
2300- -
Dorma 8812 Offset Slide Arm for RTS88
The Dorma 8812 Offset Slide Arm for RTS88 is used on in the RST31, RST30, RTS29, RST28, RST27, RTS26 and RTS25 packages. This arm is used on Single Acting Doors. The track measures 13" long by 1-3/16" wide by 7/16" thick. This is the arm you probably have if you are using 3/4" offset hinges or 4-1/2" wide butt hinges.
Dorma Part # 8812
G8812 -
Dorma 8831 Top Arm | For use with RTS88
The Dorma 8831 Top Arm for RTS88 is for use on Single and Double Acting doors. This arm is known as a side load arm, and usually has a notch in the door at the top to access the arm fastening block. This piece measures 10-1/2" long by 1-3/8" wide at the widest part, and is 1/2" thick. This is the standard arm in the RST01 and RST02 Packages.
Dorma Part # 8831
G8831 -
Dorma 8832 Top Arm and Channel for RTS88
The Dorma 8832 Top Arm with Channel for RTS88 is for use on Double and Single Acting Doors. We usually find this arm on wood doors. This arm is 10-5/8" long by 1-1/2" wide at the widest point, and is 5/8" thick. It is the standard arm in the RST04, RST05 and RST06 packages.
Dorma Part # 8832
G8832 -
Dorma 8835 Top Arm for RTS88
The Dorma 8835 Top Arm for RTS88 is for use on Double or Single Acting doors that have a 1" top rail. This arm is used on aluminum framed glass storefront doors. The arm is 10-7/8" long and 1-3/8" wide. The spindle lug 1" thick. This is the standard arm on the RST07 and RST10 packages.
Dorma Part # 8835
G8835