Von Duprin Exit Devices
-
Von Duprin 88 Axle Package 090006 090082
Von Duprin Exit Device 88 Axle Package
Von Duprin 88 Axle Package
New style axle snaps together, and replaces the old style which were screwed together with allen wrenches. This style of axle has been around since about 1990. The piece on the right is only used for taking the axle apart.
Von Duprin Part # 090006 or 090082
88R40 -
Von Duprin 8827 Special Chassis Nut 050277
Von Duprin 8827 Special Chassis Nut 050277
The 8827 Special Chassis Nut goes on the ends of the 8827 Chassis Tie Rod. The Nut is threaded all the way through so the cover mounting screws can then be threaded on it also. The nut is 3/8" long by 1/4" hex.
Von Duprin Part # 050277
Old Von Duprin Part # 96065288VR190 -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
Von Duprin 8827 Chassis Tie Rod Pkg 050328
Von Duprin 8827 Chassis Tie Rod Pkg 050328
The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.
Von Duprin Part # 050328
Old Von Duprin Part # 96761688VR195 -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Von Duprin 55 Hinge Case Spring 090052
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
Von Duprin part # 090052
55R200 -
Von Duprin Dogging Hook 090044
The Von Duprin Dogging Hook 090044 is the piece that grabs the push bar mechanism and keeps it in the dogged position. The does wear out, but it takes a long time. This piece is used on the 22, 33A, 35A, 98 and 99 series devices made after 1997. We sell this part individually and it is #5 on the diagram.
G090044 -
Von Duprin 55 Dog Screw-090053
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
Von Duprin part # 090053
55R85 -
Von Duprin 992/994 Lift Spring 971573
Von Duprin 992/994 Lever Lift Spring 971573
The spring measures 1-5/8" long with a 7/16" diameter. We find two of these springs per 992 and 994 series lever trims. These springs help support the lever handle and return it to the proper position.
Von Duprin Part # 971573-00
G971573 -
Von Duprin 88 Tube Attaching Ring 090021
The Von Duprin 88 Tube Attaching Ring 090021 is also used on the Von Duprin 55. The ring fits over the device lever arm, and is expanded by the Wedge (88R90) and the Wedge Tite Screw (88R100). When the Wedge Tite Screw is tightened the Ring expands and keeps the crossbar parallel to the door. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110 -
Von Duprin 88 and 55 Wedge Tite Screw 090081
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
Von Duprin Part # 090081
88R100