Parts
When you purchase panic and exit devices from RBA Door, every product will meet local building codes as well as your expectations for performance and quality. All panic device hardware and accessories are built with durability, convenience and value in mind. No matter the project, our panic devices are a well-built choice at a reasonable price.
-
Adams Rite EL8800 12 and 24 Volt Solenoid
The Adams Rite EL8800 Solenoid is the mechanism that retracts, or in this case turns the wheel to unlock the panic device. There are two versions one for 12 volt systems 31-0735-IP, and the 24 volt system 31-0736-IP.
The 12 Volt Solenoid is wrapped in red tape, the 24 volt is wrapped in white tape.
G31073X -
Doromatic Exit Device 2090 Active Case
The Doromatic Exit Device 2090 Active Case is for use on the 1090 and 2090 panic hardware. This device has been around since the early 1970's, and is now called the Falcon 2090 Active Case, but it is the same piece. Includes all of the interior hardware. Just unscrew or loosen the three set screws and remove your old case and install and tighten the three set screws. Housing measures 7-1/2" long by 1-3/16" wide, mounting studs have a 6-1/4" center to center distance.
LEFT HAND HOUSING SHOWN IN PICTURE
4270902740 Left Hand Aluminum Stock
4270902742 Left Hand Dark Brown Stock
4270902743 Left Hand Black * One week lead time
4270902746 Right Hand Aluminum Stock
4270902748 Right Hand Dark Brown Stock
4270902749 Right Hand Black * One week lead timeG209001 -
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Von Duprin 8827 Top Latch Case 050460
The Von Duprin 8827 Top Latch Case 050460 is for non fire rated doors. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted position.
Von Duprin part # 050460
Old Part # 10175088VR10 -
Von Duprin 8827 Bottom Latch Case 050461
The Von Duprin 8827 Bottom Latch Case 050461 is used on all Von Duprin 8827 non fire rated exits. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. Included mounting screws.
Von Duprin Part # 050461
Old part # 10175188VR170 -
Von Duprin 8827-F Top Latch Kit 050462
The Von Duprin 8827-F Top Latch Kit 050462 is the Top Latch Kit for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted postion.
Von Duprin Part # 050462
Old Part # 10267688VR10F -
Von Duprin 8827-F Bottom Latch Kit 050463
Von Duprin 8827-F Bottom Latch Kit 050463 is the Bottom Latch Kit for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted position.
Von Duprin Part # 050463
Old Part # 10268188VR170F -
Von Duprin 050130 Fitting Set for 5654 / 5754
The Von Duprin 050130 Fitting Set is for the 5654 / 5754 Mullions. Set includes top and bottom fittings, all of the mounting screws. The Fitting measures approximately 11/16" wide on face closest to the door and 2-3/8" at the widest point. The depth is 3-1/8".
Von Duprin Part # 050130
G050130- -
Von Duprin Panic Device 230L Lever Trim
The Von Duprin Panic Device 230L Lever Trim will work on the 22 and 2227 series exit devices. In 2008 this lever was redesigned and went from a key in the lever to the new style which has the key above the lever. The plate measures 3" wide by 6-3/8" high and is 15/16" thick. This lever only comes in sprayed aluminum or dark bronze. We also have replacement parts for this particular trim piece in stock, email us under the contact tab at the top of the page.
Cylinder not included
22L -
Von Duprin 386DT Dummy Trim
Von Duprin 386DT Dummy Trim
This Von Duprin 386DT Dummy Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Duprin 33A on the inside so they are on cohesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386DT Dummy Trim is non handed.
386DT -
Dor-o-Matic Falcon EL1690-EL1790-EL2390 Solenoid
The Dor-o-Matic Falcon 4758959 Soleniod is used on the EL1690, EL1790, and EL2390 Electric Latch Retraction exit devices. The Solenoid measures 4-1/8 inches long including mouting flange, and has an 1-3/4 inch diameter. The mounting screw spacing is 1 inch on centers. The Plunger is included and has a 7/8 inch diameter and is 2-15/16 inches long. We find the number 971687 on the solenoid.
G47639878