Search results for: 'ROLLERS'
- Did you mean
- roller 0
- Related search terms
- rollers for sizing door bottom 882
- rollers+for+sizing+door+bottom 1018
- rollers+for+spring+door+bottom 1026
- rollers for spring door bottom 891
- rollers for spring door bolt 883
- rollers for spring door bars 895
- rollers for spring door base 874
- rollers for spring door brush 908
- rollers for sizing door black 892
- rollers for sizing door brass 904
-
Roller Bumper Roller Only
One of the most common issues with Roller Bumpers and Gravity Type Coordinators is that the rubber wheel dries out and eventually falls off. With this Replacement Roller For Roller Bumper, you can now just change out the wheel. The wheel has 15/16" diameter and is 7/16" wide. The hub diameter is 3/16". This package ships with the wheel and a replacement axle that features a "fast rivet" head.
GJRB4R -
Roller Bumper Straight Arm 4" RB471
The Ives Roller Bumper Straight Arm 4" RB471 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 4-1/2" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB4 or GJRB4.
GJRB4- -
Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3- -
Ives RL30 Roller Latch
Ives RL30 Roller Latch
The Ives Roller Latch RL30 is constructed of Forged Brass and Plated to your finish. Furnished with a Nylon Roller. Body measures 1" wide by 3-3/8" high by 1-11/16" deep. The roller has a maximum projection of 3/8" and is easily adjustable.
RL30- -
LCN Sentronic Door Closer Roller - 3034
The LCN Sentronic Door Closer Roller - 3034 is used on all of the LCN Track Closers, and Sentronic Closers. Nylon wheel is 1-1/16" diameter by 3/8" thick. The shaft is has a 1/2" diameter by 1-1/8" long. However in November of 2015 they started shipping the roller with the Slider 168 attached to it, with a retaining ring. LCN Started using this Roller Assembly in December 2018.
LCN part # 4040SE-3034
4040SE-3034 -
Ives Roller Bumper Straight Arm 6" RB472
The Ives Roller Bumper Straight Arm 6" RB472 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 6" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB6 or GJRB6.
GJRB6- -
Ives RL32 Roller Latch
Ives RL32 Roller Latch
The Ives RL32 Roller Latch is constructed of Brass and Plated to your desired finish. The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep. The roller is constructed of Nylon, and has an adjustable projection up to 1/2". Fits a standard heavy-duty cylindrical lock cutout.
RL32- -
Doromatic TD35 Roller Strike
The Falcon TD35 Roller Strike is used with the Dor-o-Matic Falcon 1590, 1790, and 2090 panic device where you are trying to protect the frame when the door closes. The strike has been manufactured since the 1970's. This part is also known as a Kawneer 133479 strike. The strike ships with mounting screws in a painted black finish. This style of strike is also known as a Blade Strike.
Doromatic Falcon Part # TD35 or 4270107393
GTD35 -
Ives RLPART.1025 Roller and Rivet for RL30/RL1152
Ives RLPART.1025 Roller and Rivet for RL30/RL1152
This replacement Nylon Roller and Rivet Package is for the Ives RL30 and RL1152 Roller Latches. The Roller measures 3/4" high by 5/8" diameter. The Rivet measures 1-1/16" long and is threaded on one side.
Ives Part # RLPART.1025
RL30NR -
LCN Sentronic Door Closer 4040SE-168 Slider
The LCN Sentronic Door Closer 4040SE-168 Slider used to be just the slider, the metal part. In October of 2015 they changed the part so the roller is now included and they are held together by a snap ring or E-clip.
The slider is not longer sold separately, it is sold with the roller. You have to take the Assembly apart to get just the slider.
4040SE-168 -
Von Duprin Strike 264
The Von Duprin Strike 264 measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.
Von Duprin Part # 264
264 -
LCN Sentronic Door Closer 3130SE
The LCN Sentronic Overhead Concealed Door Closer 3130SE is shipped with a standard arm, 24V or 120V SE track (please specify), track roller, and wood and machine screw pack. Sized cylinders for interior doors to 4’0”. Functions as full rack and pinion door closer when hold-open is not engaged or current is interrupted. Handed for right or left swinging door. Interfaces with fire alarm systems.
LCN Sentronic Door Closer 3130SE parts are also available.
3130SE -
Falcon 299 Strike
Falcon 299 Strike
The Falcon 299 Strike is used on the 25-R and 24-R Devices. The 299 strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". This strike is the same as the Von Duprin 299 Strike.
Ships with shim and mounting screws
Falcon Part # 299
Fa299 -
Dorma RTS88 Door Closer-
The Dorma RTS88 Door Closer is an overhead concealed closer for both single and double-acting doors. It is one of the more popular overhead concealed closers on the market today. The RTS88 will consist of a steel cam, rollers, and springs housed in a compact cast iron body. Closers will be capable of being installed in minimum 1-3/4" x 4" headers. RTS88 will have maximum door opening to 90º or 105º, trim conditions permitting. Sweep and latch speed will be controlled by two noncritical adjustment valves from 90º or 105º to closed. Built-in pressure relief valve will protect the closer from abuse caused by forced closing. A mechanical backcheck combined with a positive stop at 90º or 105º will be provided to protect the door and frame. The RTS88 closer will be available with hold open at 90º or 105º, or without hold open. The product shown here is just the replacement cylinder.
RTS88 -
Ives Gravity Type Door Coordinator COR9G
Gravity Door Coordinator 9"
The Ives COR9G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR9G-26D for use on pairs of doors with astragal on active door over 4' or with astragal on inactive door over 3'4" or with astragal on both doors over 2'10" Brushed Chrome Finish.Ives part # COR9G-26D 9" Arm Projection
COR9G -
Cal Royal 4400 Rim Panic Device
The Cal Royal 4400 Rim Exit Device has a Grade 2 rating. The device features a 3/4" Latchbolt, Roller Strike and a 1" diameter Crossbar. The device comes in a brushed chrome and dark bronze finish, and comes with either a 36" or 48" crossbar. You would need a 4-1/2" minimum stile width.
CR4400- -
Ives Gravity Type Door Coordinator COR7G
Gravity Door Coordinator
The Ives COR7G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR7G-26D for use on pairs of doors with astragal on active door up to 4' or with astragal on inactive door up to 3'4" or with astragal on both doors up to 2'10" Brushed Chrome Finish.Ives part # COR7G-26D 7" Arm Projection
1836 -
Jackson Panic Device 1095 Standard Strike
The Jackson Panic Device 1095 Standard Strike is a strike they have been using for the past 20 years. You might have one of the older roller strikes, but this will work in its place. The older style roller strike is no longer available. Jackson Exit Device part # 30-2436.
G109556 -
Von Duprin Strike 299
The Von Duprin Strike 299 is used on the 22, 88, 98, and 99 Rim Devices and also as a Top Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 299 strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". Ships with shim and mounting screws.
299 -
Floor Door Stop / Holder 534
Automatic Floor Type Holder and Stop
A replacement holder and stop that has been around for many years. This style of Holder can be found in many of the schools, churches and hospitals that were built in the 1960's and 1970's. Cast brass construction, and then chrome plated. Measures 3-11/16" high by 3" wide with a 1-15/16" projection. The strike is 1-3/16" high. Spring loaded brass roller, rolls over the the strike to lock the door in the open position. To release, just give the door a tug. Designed for doors with a door to floor clearance of less than a 1/2".
GJ534- -
Wall Door Stop / Holder WS45
The Ives Wall Door Stop / Holder WS45 was introduced about 50 years ago as the Glynn-Johnson W45A or GJW45A. When they were purchased by H.B. Ives, it became the WS45. They are constructed of cast Brass or Bronze and then plated to the desired finish. This door stop is unique because the wall does not have to be parallel to the door for it to latch and hold the door open. Spring loaded roller rides up the face of the strike, seating itself on the strike, holding the door firmly in the open position. A heavy rubber pad cushions the shock and absorbs the sound. With unit mounted on door and the strike on wall, vertical adjustment is available on body. The strike is adjustable 45 degrees left or right, both adjustments easily accomplished at time of installation or at a later date. WS45 strike is furnished with wood screws for drywall mounting.
GJW45A- -
Sargent 2727 Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warranty2727EO- -
Sargent 2828 Series Rim Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warrantyG20EO- -
Von Duprin Strike 299F
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
Von Duprin Part # 299F
299F -
LCN Sentronic Door Closer 4314ME
LCN Sentronic Door Closer 4310ME
Standard LCN Sentronic Door Closer 4310ME series closer shipped with a 24V or 120V cylinder (please specify) on a mounting plate, metal cover, Swing-Free arm, track, track roller, and wood and machine screw pack. See 4310ME Series pages 23 & 24 for options. Sized cylinders for interior doors to 4’0”. Functions as full rack and pinion door closer when hold-open is not engaged or current is interrupted with Swing-Free arm engaged. Handed for right or left swinging door. Concealed or exposed electrical connections. Built-in “On/Off” switch controls hold-open function. Swing-Free arm allows door to be moved without door closer resistance. Interfaces with fire alarm systems. LCN Sentronic Door Closer 4310ME part are also available.
4310ME- -
Wall Door Stop / Holder WS40
The Ives Wall Door Stop / Holder WS40 is a door holder that has some history. We see this product in many schools, hospitals and churches that were built in the 50's, 60's and 70's. The WS40 was originally made and designed by Glynn-Johnson out of Chicago, Illinois, and was called the W40 or GJW40. H.B. Ives purchased Glynn-Johnson in 1990's and mergered this product into there offering, and changed the part # to WS40. The holder is made of cast brass or bronze and plated to your desired finish. The holding mechanism has a rubber bumper inside it to act as a door stop, and a brass spring loaded roller to act as a holder. The product ships with a universal screw package to mount on all types of walls. For the best results with this stop/holder the door and wall should be about 3-1/2" apart in the open position.
Base Height: 2"
Base Width: 2-1/2"
Base Projection: 2-1/4"
Engaged Projection: 3-1/2"
Strike Height: 2-1/16"
Strike Width: 3/4"
Strike Projection: 2"GJW40- -
LCN Door Closer 4040SE Track Assy 4040SE-3038
The LCN Door Closer 4040SE Track Assy 4040SE-3038 replaces all Sentronic tracks for the 3130SE, 4010SE, 4110SE and 4040SE Closers. Track includes the roller, 4040SE-3034 and new mounting screws. The replacement track measures 21-3/4" on center for the mounting screws, which may be different then the 3130SE, 4010SE, 4110SE and older 4040SE Tracks. The replacement track is the only way we know of to replace the solenoid. Specify voltage, and color when ordering.
LCN Part # 4040SE-3038
4040SE-3038 -
LCN Door Closer 2031 -2035
The concealed LCN Door Closer 2031 -2035 Pacer® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom. It is considered an application specific closer, due to the cylinder spring sizing and handing. The standard 2030 series closer shipped with standard arm, standard track, mounting/finish plate, and wood and machine screw pack. Aluminum frame requires minimum 1 3/4” x 4” tube.
2030