Search results for: 'rolls for sizing door brass'

Zipper Pile Weatherstrip .270" Backing - .300" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

4" Kickdown Door Holder Grand Standard

Frequently we are asked, “What is the heaviest duty kick down holder  you sell?”  The answer to that question is any of  Grand Specialty door holders.  These door stops are American made and simply the best out there.   They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg.  They are constructed of steel, and not cast like all of the other door holders made.

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

• No roll pin at pivot point
• Mallable with a pair of pliers
• Rubber shoe held on by a screw
• American Made
• Zinc plated steel

 The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.

Automatic Floor Type Holder and Stop

A replacement holder and stop that has been around for many years.   This style of Holder can be found in many of the schools, churches and hospitals that were built in the 1960's and 1970's.  Cast brass construction, and then chrome plated. Measures 3-11/16" high by 3" wide with a 1-15/16" projection. The strike is 1-3/16" high. Spring loaded brass roller, rolls over the the strike to lock the door in the open position. To release, just give the door a tug.  Designed for doors with a door to floor clearance of less than a 1/2".

Zipper Pile Weatherstrip .270" Backing - .200" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Zipper Pile Weatherstrip .270" Backing - .250" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

5" Kickdown Door Holder Grand Standard

Frequently we are asked, “What is the heaviest duty kick down holder  you sell?”  The answer to that question is any of  Grand Specialty door holders.  These door stops are American made and simply the best out there.   They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg.  They are constructed of steel, and not cast like all of the other door holders made.

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

• No roll pin at pivot point
• Mallable with a pair of pliers
• Rubber shoe held on by a screw
• American Made
• Zinc plated steel

 The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.

made by Grand Specialties 605z 605b

3" Kickdown Door Holder / Stop Zinc Plated Mickey

Zinc plated cold rolled steel,
Made in the USA
3" Arm Length

made by Grand Specialties

The Lifetime Polished Brass Door Kick Plate has a 16 gauge (.050″ thick) base metal, that is then plated with a artificial brass finish that is then polished. The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD. Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish. The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates.

Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.   You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes, but they are made of Stainless Steel, which is a tough metal to drill. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.

Custom sizes available starting around $0.40 per square inch depending quantity

Please allow 1 week shipping time

Solid brass kick plate, polished to mirror finish.  We can no longer get the solid brass plates, the lifetime polished brass will be shipped in its place.

The standard Polished Brass Door Kick Plate is a solid brass kick plate that is polished and then clear coated to prevent oxidation. These plates are 16 gauge or .050″ thick. A draw back of the Polished Brass Plates is oxidation. If the plate becomes scratched or dented, there is a good probability that the clear coat delaminates and moist could get under the surface. When this happens, the plate will tarnish. The brass base material is softer, so the chances of them becoming scratched or dented in commercial applications is pretty high.

Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.   You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.

I would highly recommend the Lifetime Brass if these plates are going to be mounted outside. Solid brass is soft, and tends to dent easily and the clear coat can be compromised. The Lifetime Brass plates do not require a clear and will last a lot, lot longer!

Custom sizes available starting around $0.40 per square inch depending quantity

The Brushed Brass Door Kick Plates are the same as the Lifetime Polished Brass Door Kick Plates, solid stainless steel base metal, 16 gauge (.050" thick), but the surface is Satin or Brushed.  Because it is an artifical finish they will not tarnish.  Custom sizes available starting around $0.41 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

6" Kickdown Door Holder Grand Standard

Frequently we are asked, “What is the heaviest duty kick down holder  you sell?”  The answer to that question is any of  Grand Specialty door holders.  These door stops are American made and simply the best out there.   They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg.  They are constructed of steel, and not cast like all of the other door holders made.

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

• No roll pin at pivot point
• Mallable with a pair of pliers
• Rubber shoe held on by a screw
• American Made
• Zinc plated steel

 The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.

Made by Grand Specialties 606z and 606br
606BR is not longer manufactured  

The Lifetime Polished Brass Door Kick Plate 8 x 30 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 8 x 34 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 6 x 28 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 10 x 34 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

Satin Nickel US15-18 ga. (.037)
Lifetime Polished Brass US3 PVD -16 Ga (.050") Stainless steel plate with a highly durable polished brass looking finish.

Custom sizes available starting around $0.25 per square inch depending quantity

Please allow 1 week shipping time

Finishes

Floor Mounted Door Stop 535

Cast Brass or Bronze construction
2-1/2" diameter base x 3-1/8" high
Fasteners included

Brushed Brass Kick Plate US4 -16 Ga (.050")
Solid brass plate with brushed finish, then clear coated

Custom sizes available starting around $0.25 per square inch depending quantity

Kick Plate comes with screws for mounting

Please allow 1 week shipping time

Finishes

Brushed Brass Kick Plate US4 -16 Ga (.050")
Solid brass plate with brushed finish, then clear coated

Custom sizes available starting around $0.25 per square inch depending quantity

Kick Plate comes with screws for mounting

Please allow 1 week shipping time

Finishes

Floor Door Stop / Holder 536

The Stop and Holder 536 is considered a manual door holder.   It is a manual door holder because you have to physically bend over and hook and unhook the holder.  This holder is constructed cast brass or cast bronze and then plated to your desired finish.  The stop measures 2-1/2" in diameter and 3-7/8" overall height, with a center line height of 2-1/2" from the base to the center of the rubber stop.  It ships with all of the fasteners.

The Lifetime Polished Brass Door Kick Plate 6 x 32 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 8 x 28 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

Floor Door Stop 524

The 524 Door Stop is one of the more interesting door stops we have.   They are constructed of cast brass that is then plated to your finish.  It measures 1-1/4" in diameter and is 1-1/2" tall.  One of the benefits of this door stop is there are no exposed screws.  The 524 ships with a 12-24 x 1" machine screw, a plastic anchor and a lead anchor.

Polished Brass Door Kick Plate : 8" x 32"

The standard Polished Brass is a solid brass kick plate that is polished and then clear coated to prevent oxidation. These plates are 16 gauge or .050" thick. A draw back of the Polished Brass Plates is oxidation. If the plate becomes scratched or dented, there is a good probability that the clear coat delaminates and moisture could get under the surface. When this happens, the plate will tarnish. The brass base material is softer, so the chances of them becoming scratched or dented in commercial applications is pretty high.  You might want to consider Lifetime Brass, which are the same cost per square inch.

Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8" Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10" will have 10 holes for plates up to 33" and 12 holes for plates between 33 and 40".

Custom sizes are available, they run about $0.23 per square inch.

Please allow 1 week shipping time

Finishes

Polished Brass Door Kick Plate : 8" x 34"

The standard Polished Brass is a solid brass kick plate that is polished and then clear coated to prevent oxidation. These plates are 16 gauge or .050" thick. A draw back of the Polished Brass Plates is oxidation. If the plate becomes scratched or dented, there is a good probability that the clear coat delaminates and moisture could get under the surface. When this happens, the plate will tarnish. The brass base material is softer, so the chances of them becoming scratched or dented in commercial applications is pretty high.  You might want to consider Lifetime Brass, which are the same cost per square inch.

Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8" Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10" will have 10 holes for plates up to 33" and 12 holes for plates between 33 and 40".

Custom sizes are available, they run about $0.23 per square inch.

Please allow 1 week shipping time

Finishes

Brushed Brass Kick Plate US4 -16 Ga (.050")
Solid brass plate with brushed finish, then clear coated

Custom sizes available starting around $0.25 per square inch depending quantity

Kick Plate comes with screws for mounting

Please allow 1 week shipping time

Finishes

Polished Brass Door Kick Plate : 6" x 28"

The standard Polished Brass is a solid brass kick plate that is polished and then clear coated to prevent oxidation. These plates are 16 gauge or .050" thick. A draw back of the Polished Brass Plates is oxidation. If the plate becomes scratched or dented, there is a good probability that the clear coat delaminates and moisture could get under the surface. When this happens, the plate will tarnish. The brass base material is softer, so the chances of them becoming scratched or dented in commercial applications is pretty high.  You might want to consider Lifetime Brass, which are the same cost per square inch.

Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8" Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10" will have 10 holes for plates up to 33" and 12 holes for plates between 33 and 40".

Custom sizes are available, they run about $0.23 per square inch.

Please allow 1 week shipping time

Finishes

Polished Brass Door Kick Plate : 8" x 28"

The standard Polished Brass is a solid brass kick plate that is polished and then clear coated to prevent oxidation. These plates are 16 gauge or .050" thick. A draw back of the Polished Brass Plates is oxidation. If the plate becomes scratched or dented, there is a good probability that the clear coat delaminates and moisture could get under the surface. When this happens, the plate will tarnish. The brass base material is softer, so the chances of them becoming scratched or dented in commercial applications is pretty high.  You might want to consider Lifetime Brass, which are the same cost per square inch.

Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8" Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10" will have 10 holes for plates up to 33" and 12 holes for plates between 33 and 40".

Custom sizes are available, they run about $0.23 per square inch.

Please allow 1 week shipping time

Finishes

The Lifetime Polished Brass Door Kick Plate 6 x 30 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 6 x 34 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

The Lifetime Polished Brass Door Kick Plate 8 x 32 inches has a 16 gauge (.050" thick) base metal, that is then plated with a artificial brass finish that is then polished.  The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD.  Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish.  The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates. Custom sizes are available starting around $0.23 per square inch depending quantity.  Kick Plate comes with screws for mounting.  Please allow 1 week shipping time.

Push Bar Adjustable 452

Finishes:
US26/625 polished chrome
US26D/626 brushed chrome
US3/605 polished brass
US4/606 brushed brass
US5/609 antique brass
US10/612 brushed bronze
US10B/613 dark bronze

Material: Brass
Material Size: 5/8" round tube adjustable to 36"
Base: 5/8" x 8-1/2"
Clearance: 1/2"
Projection: 1-1/8"

The Wall Door Holder/Stop 531 features cast brass or bronze finish which is then plated to the desired finish.  This is considered a manually operated door holder, because it does not latch automatically.  It features a 2-1/2" base with 3-5/8" projection, and ships complete with all of the needed fasteners.

Push Bar Adjustable 450

Finishes:
US3/605 Polished brass
US4/606 Brushed brass
US10B/613 Dark bronze
US26/625 polished chrome
US26D/626 brushed chrome

Material: Brass
Material Size: 5/8" Rd Tube Adjustable up to 36"
Clearance: 1/2"
Projection: 1-1/8"
Fasteners: Surface Mount only

Brushed Brass Kick Plate US4 -16 Ga (.050")
Solid brass plate with brushed finish, then clear coated

Custom sizes available starting around $0.25 per square inch depending quantity

Kick Plate comes with screws for mounting

Please allow 1 week shipping time

Finishes

Brushed Brass Kick Plate US4 -16 Ga (.050")
Solid brass plate with brushed finish, then clear coated

Custom sizes available starting around $0.25 per square inch depending quantity

Kick Plate comes with screws for mounting

Please allow 1 week shipping time

Finishes