Search results for: 'HINGES'
- Related search terms
- Hinges used on swinging doors for 1012
- hinges used on swinging doors for kick 1029
- hinges used on swinging doors for kit 1042
- hinges used on swinging door for kitchen 1012
- hinges used on swinging door for 1012
- hinges used on swinging door for kit 1041
- hinges used on swinging door for kick 1029
- hinges cal jackson panic device brooke for td door 1164
- hinges cal jackson panic device broken for td door 1165
- hinges cal jackson panic device bronz for td door 1200
-
Dorma 8812 Offset Slide Arm for RTS88
The Dorma 8812 Offset Slide Arm for RTS88 is used on in the RST31, RST30, RTS29, RST28, RST27, RTS26 and RTS25 packages. This arm is used on Single Acting Doors. The track measures 13" long by 1-3/16" wide by 7/16" thick. This is the arm you probably have if you are using 3/4" offset hinges or 4-1/2" wide butt hinges.
Dorma Part # 8812
G8812 -
Sargent 20/30/60 End Cap Bracket
The Sargent 20/30/60 End Cap Bracket is used with the larger end cap. This end cap has been manufactured for the last 40 years and started its life on the obsolete 60 Series. The bracket holds the hinge side of the exit device on the door, and the G20300C fits over the top of it.
Sargent part #68-2141
G20300B -
Magnetic Door Stop/Holder
Magnet Door Stop
Hands-free magnetic door stop/holder. All you need to do is open the door and a strong maget will keep it open until you close it. Mounts horizontally or vertically. Includes fasteners plus 1 concrete and 3 hollow wall anchors.
Not for use on doors with spring hinges or door closers.
GDS100 -
Jackson 1085 30-1242 / 30-1243 Lever Arms
The Jackson 1085 30-1242 / 30-1243 Lever Arms are for use with the Jackson 1085 Housings, both sides. And the Jackson 1095 Inactive (hinge side) Housings. To determine hand, stand inside and look out the door, what is side is the arm on? If it is on the Right then order Right.
G10852x -
Monarch 17/18/19 Series Dogging Cover
Monarch 17/18/19 Series Dogging Cover
This Monarch 17/18/19 Series Dogging Cover goes over the dogging mechanism on the hinge side of the exit device. Sometimes when the end cap goes missing, this cover plate also disappears.
Monarch old part #s 195 and 194
Monarch/Falcon new part #'s 650297 and 650303G19R80 -
Monarch 19 Series End Cap Bracket
Monarch 19 Series End Cap Bracket
This steel bracket holds the hinge side of the panic bar on the door. The end cap then fits over it for a finished look. Bracket measures 1-5/8" tall by 1-1/4" wide with a 15/16" projection. Sometimes shipped with a mounting barrel nuts and screw.
Monarch Falcon Part # 650320 or old part # 600108
G19R100B -
LCN Door Closer 4011FL | LCN 4011 FL
The LCN Door Closer 4011FL is shipped with fusible link arm, standard plastic cover, and self reaming and tapping screws. Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder (4011) adjustable for interior doors to 4’6” and exterior doors to 3’6”. Included arm has a fusible link that melts at 120 degrees, allowing to door to close. Door can be closed any time with a gentle pull. Closer mounts hinge side, specify right or left swinging door. 4011 cylinder meets ADA requirements.
We ship the 4011 FL
4010FL- -
LCN Door Closer 1461
The LCN Door Closer 1461 series closer ships with regular arm, a slim line plastic cover, and self reaming and tapping screws. Non-sized (1-6) cylinder is adjustable for interior doors to 5’0” and exterior doors to 4’0”. Closer mounts hinge side, top jamb and parallel arm on either right or left swinging doors. The narrow foot print allows this door closer to be mounted on the top jamb and narrow stile doors without a drop plate.
We ship the 1461 Rw/PA
1460- -
Adams Rite 41-0903-IP Metal End Cap
The Adams Rite Metal End Cap is for the hinge side of the door and replaces the plastic version (25-0471). This cap can be used on the 3100, 3300, 3600, 3700, 3900, 8100, 8200, 8300, 8400, 8500, 8600, 8700, 8800 and 8900. We find the number 23-0600 cast in to the end cap.
Adams Rite Part Number 41-0903-IP or 41-0903-119
G410903 -
Von Duprin 22 End Cap Only 968601
The Von Duprin 22 End Cap Only 968601 is the end cap that goes on the hinge side of the door. When the cap breaks off the Dogging Cover Plate just slides off. Works on all of the Von Duprin 22 exit devices. If you need the bracket also, please order part # G22R10. Black plastic construction. As of October 1, 2014, Von Duprin no longer sells just the Plastic Cap Only. The complete End Cap and Bracket 900981 will be shipped in its place.
Von Duprin Part # 968601
G22R25 -
LCN Door Closer 4031
The LCN Door Closer 4031 is shipped with forged regular arm, metal cover and wood/self-tapping machine screw pack. Non-sized (1-4) 4031 cylinder for exterior doors to 36” (914 mm) and interior doors to 48” (1219 mm). Closer mounts hinge side, top jamb, and parallel arm, on either right or left swinging doors. Closer meets ADA requirements. The hole spacing on this closer will not match the 4030's that LCN produced up to 1997, that was a completely different door closer.
We ship the 4031 Rw/PA
4030- -
International 8600 Series End Cap
The International 8600 Series End Cap is used on the hinge side of the the exit device. This cap includes the mounting bracket and the mounting screws. It is constructed of a die cast metal for years of service. The piece measures 2-3/8" by 2-1/4" by 1-1/2". This end cap is used on the International Door Closer models, 8510S, 8610S, 8710S, 8810S, 8620S, 8530S, and 8650S devices, along with the same devices ending in F.
INT8600EC- -
Von Duprin 55 End Case Kit 050196 and 050197
The Von Duprin 55 End Case is the housing on the hinge side of the door. The function of this housing is to lift the cross bar, and support the function of the Active Case. If your housing is on the right side when standing inside looking out, then you would order the Right Hand Case. The package includes the housing, springs and back plate, the arm is not included. The current part number on this part is 050196 and 050197, the old part number is 111931 and 111932.
Other finishes are available upon request.
55R30 -
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Dogging Cover Plate. Plate covers the dogging assy, or hinge side of the exit device. This plate sides off when the plastic end cap breaks or goes missing.
Von Duprin Part # 968595 measures 10-3/4" Long for 3' devices
Von Duprin Part # 968596 measures 16-3/4" Long for 4' devicesG22R90- -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Jackson Panic Device Center Case 1085/1095
The Jackson Panic Device Center Case 1085/1095 is for use with the 1085 devices for both and left, and the inactive case of the 1095. Case is easily removed by loosening the two 1/8" Allen screws and one on the bottom. Includes everything in the housing. The distance between the mounting studs on this Case is 6-5/16"
Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm AssemblyHousing Shown in Aluminum
G1085XX -
Von Duprin 99 Cover Plate 050114
The Von Duprin 99 Cover Plate 050114 is for use on the 33A, 35A, 98 and 99 devices. Covers the dogging assembly on the hinge side of the door. The usually fall off when the End Cap is not on the exit device. Von Duprin is only shipping a 20-1/2" cover plate now, which will work on 3' and 4' doors, you will have to cut more off if you have a 3' device with a hack saw or chop saw.
Von Duprin Part # 050114 and 050117 Hex Key Dog Conversion Kit
Von Duprin 99 Cover Plate 050114
G99R50 -
LCN Door Closer 4011
The LCN Door Closer 4011 is known as the Smoothee. The door closer ships with regular arm, standard plastic cover, and self reaming and tapping screws. This is considered an application specific closer, meaning you have to specify left and right swing door, and it can only be mounted as a regular armed closer. A regular armed closer is a closer that is mounted on the pull side of the door. The non sized clinder will work on doors from 30" to 60" interior doors, or 26" to 48" exterior doors, and can be adjusted to meet ADA specifications. This door closer is ideal for areas of high traffic and abuse, like schools or any other areas of extreme use. We ship the 4011 REG.
4010 -
Floor Door Stop / Holder
The F20 or GJF20 was a mainstay of Glynn-Johnson for years. When the Glynn-Johnson door stop line merged with H.B. Ives it became the FS20. This door stop has been discontinued from Ives, but we have been able find a large stock. This Floor Mounted Door Stop also holds the door open, when in the latched position you can push the door and the holding latch will flip up and unlock thee holding clip. It is constructed of cast bronze or brass and then plated to your desired finish. This stop has a 2-1/2" long base that is 1-1/2" wide. The overall height is 3-1/8" with a 2-5/16" floor to rubber stop centerline. For use with door undercut up to 2-1/2".
GJF20- -
5" Kickdown Door Holder Grand Standard
5" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.
made by Grand Specialties 605z 605b
GJ605- -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
4" Kickdown Door Holder Grand Standard
4" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.
GJ604- -
10" Kickdown Door Holder Grand Standard
10" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 9-3/8" to the Floor when mounted.
Made by Grand Specialties 610z
GJ610 -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606-