Search results for: 'AUTOMATIC DOOR'
- Related search terms
- door series 30 push bar panic exit dor parts 1311
- door series push bar panic exit dor cal parts 1307
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit dent parts 1306
- door series 30 push bar panic exit deep parts 1309
- door series 30 pull bar panic exit detex parts 1306
- door series 30 pull bar panic exit deep parts 1308
- door series 30 pull bar panic exit dead parts 1306
- door o matic 1 panic device 1309
- dooramatic door series 30 push bar panic exit devic parts 1314
-
Norton 9300 Door Closer-Discontinued
Norton Door Closer 9300
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- Friction hold open arm optional
- UL listed and compliant with UL10C for positive pressure
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" Hole Spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
9300- -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
Sargent Door Closer 1331
The Sargent Door Closer 1331 is a standard template closer with the 3/4” x 12” hole spacing. This closer is a great replacement for the Norton 8000 Series or Yale 3000 Series Door Closers. The closer is constructed of a cast aluminum body and has a heat treated steel pinion and rack. The 1331 has the ability to be mounted on the push, pull or top jamb, and is non handed. We stock the aluminum finish, but also have the dark bronze finish, it just might take an extra day or so. We ship the 1331-JUO.
1330- -
Yale Door Closer 51 Series
The Yale Door Closer 51 Series has been around since the early 1970's. With the advent of the aluminum framed storefront doors, this door closer was a perfect fit. The 50 series is a non-sized, non-handed closer that can be mounted on the push (parallel arm), pull (regular arm) or top jamb. A Grade 1 closer certification, means it is one of the more heavy duty closers out there. Older models may be stamped with Scoville or Eaton, which are the companies that used to own Yale. We some times find 20-0054-4001 or 20-0254-4001 stamped on the back of the closer. Ships with all mounting screws and a parallel arm bracket. The hole spacing is 3/4" by 9-1/16".
50- -
International Door Closer 5530S SVR Device-Light Duty
International 5530S Surface Vertical Rod Device-Light Duty
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steelStandard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.Standard vertical rod accommodates 7’ or 8’ doors
We offer the aluminum and dark bronze finish online, the polished brass and stainless steel finishes are available.
5530S- -
Ives Gravity Type Door Coordinator COR9G
Gravity Door Coordinator 9"
The Ives COR9G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR9G-26D for use on pairs of doors with astragal on active door over 4' or with astragal on inactive door over 3'4" or with astragal on both doors over 2'10" Brushed Chrome Finish.Ives part # COR9G-26D 9" Arm Projection
COR9G -
Ives Gravity Type Door Coordinator COR7G
Gravity Door Coordinator
The Ives COR7G has been around for at least 50 years. In the old days before electrically activated door closers fire doors would have fusible link armed door closers. When the lnk melted, the door closed, and if there was not a mullion between door, they would use this style of door coordinator so the door with the astragal would close first.
When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR7G-26D for use on pairs of doors with astragal on active door up to 4' or with astragal on inactive door up to 3'4" or with astragal on both doors up to 2'10" Brushed Chrome Finish.Ives part # COR7G-26D 7" Arm Projection
1836 -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606- -
Door Sweep 1-9/16" Long Brush
The Door Sweep 1-9/16" Long Brush is one of the longest brush sweeps we offer. The brush is 1-9/16" long, with the mounting strip being 1-3/16". The mounting strip is constructed of extruded aluminum, and the holes are slotted for adjustment. The mounting screws, which are #6 x 3/4" stainless steel sheet metal screws are included. This product is easily cut down in the field.
E609A -
Falcon / Doromatic Door Closer SC81
The Falcon / Doromatic Door Closer SC81 is an affordable, higher quality, standard template closer. This closer offers adjustable closing, latching and back check speeds, along with adjustable spring tension. It has the ability to be mounted on the push, pull or top jamb and is non handed. This closer is considered a Grade 1 closer, which is the highest grade you can get. The hole spacing is 3/4” x 12”, which is the same hole spacing as the Norton 8301, 8501 and the Yale 3301, 3501 Door Closers. We ship the SC81 Rw/PA.
SC80- -
International Door Closer 5001P Series Adjustable Spring Power
The International Door Closer 5001P Series Adjustable Spring Power is a great closer to use as a replacement for the many 3/4" by 12" mounting holed closers. This door closer is fully adjustable with sweep, latching and back check adjustments, a long with an adjustable spring tensoin control. This closer can be adjusted to less then 8-1/2" pounds of resistance to meet ADA standards. You can install this closer on the push, pull or top jamb, we ship the regular arm and a parallel arm bracket. This closer has the same mounting holes as the Norton 8000 and Yale 3000 door closers.
Hole spacing 3/4" x 12"
5001- -
Finger Protector For Doors - Exterior Push Side
Door Finger Protector - Exterior Push Side
This model is specifically designed for exterior doors on the push side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts
Our part # on this is GFG5 for the 78" length, and GFG5+ for the 83" length.
GFG-C -
Norton Door Closer 7700 Series Power Track
The Norton Door Closer 7700 Series Power Track combine the functions of a single point electromechanical door holder with the proven reliability of a 7700 Series Door Closer. The track assembly contains an arm slide and solenoid operated hold open mechanism and is available with or without an integral smoke detector. The closer is mounted on the door. The Power Track and hook-up box are mounted to the frame face for pull side installations or the frame soffit for push side installations.
Two versions, the Master Unit (PTDO) and the Support Unit (PTO). The PTDO has an integral smoke detector. The PTO can be plugged into the PTDO or into your existing fire alarm system. Both units can be mount pull side of the closed door, or the push side, please specify when ordering. Specify voltage (24 volt or 120 volt) and color (aluminum or dark brown). Dark Brown is a 3 week lead time, Aluminum is in stock.Supply Chains have really caused some issues on this door closer, we recommend calling or emailing to check the availability of this door closer.
7705PT- -
Corbin Russwin Door Closer DC6210
Corbin Russwin DC6210 Door Closer
Corbin Russwin’s history combines high-quality product and innovative design. That tradition continues with the new Grade 1 DC6000 Series door closer, designed and engineered with quality features such as captured valves and a complete range of new arms. The DC6000 series is the perfect closer for high-use openings or openings that must meet ADA requirements, such as schools, office buildings, health care facilities, and retail complexes. The series also meets UL and UL10C positive pressure requirements for fire openings.
Uses the same mounting bracket as the 100,110, 120 and 2800, 2810 and 2820 series and also the , DC220, DC2400, and DC2600
Older models may have SL72 or MS93 cast on the cylinders.
You may also find Clarksdale, MS cast on the cylinder also.DC6210-- -
Rixson Checkmate Overhead Door Holder 9 Series
Rixson Checkmate Overhead Door Holder 9 Series
Product Description & Features
• Doors are single acting
• Non-handed
• Slide track design
• Recommended for high traffic, heavy
abuse installations
• Heavy shock absorber spring provides
5-7° compression before deadstopGR09 -
International Door Closer 5510S Rim Device
International 5510S Rim Device-Light Duty
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steelStandard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.5510S- -
4" Kickdown Door Holder Brass Deluxe
4" Kickdown Door Holder Brass Deluxe
Popular priced crafted holder for interior doors.
Has 1/2" adjustment and replaceable steel re-inforced
shoe for long life. Made of steel with brass plated finish.Made by Grand Specialties
GJ6A -
Russwin Door Closer 2800/2810/2820
The Russwin 2800, 2810 and 2820 are no longer available. They have been replaced by the Corbin Russwin DC6210, which has the same hole spacings and arm. You will not have to redrill or modify your door to make the DC6210 work in place of your existing 2800, 2810 or 2820 door closers. The Corbin Russwin DC6210 has a little bit larger body due to the increased functionality of this closer. This new closer will meet all the ADA requirements.
Corbin Russwin’s history combines high-quality product and innovative design. That tradition continues with the new Grade 1 DC6000 Series door closer, designed and engineered with quality features such as captured valves and a complete range of new arms. The DC6000 series is the perfect closer for high-use openings or openings that must meet ADA requirements, such as schools, office buildings, health care facilities, and retail complexes. The series also meets UL and UL10C positive pressure requirements for fire openings.
Uses the same mounting bracket as the 100, and 2800 series.Older models may have SL72 or MS93 cast on the cylinders. You may also find Clarksdale, MS cast on the cylinder also.
DC6210a -
LCN Door Closer Traditional Springs
Replacement springs for the older Pot Type Closers. You should find a number stamped on the end plug, which should relate to the "Size" below.
LCN Size B 1-5/16" high x 2-3/4" diameter-no longer available
LCN Size C 1-1/2" high x 3" diameter- No longer available
LCN Size D 1-11/16" high x 3-1/4" diameter - No longer available
LCN Size EF 2" high x 3-3/8" diameterLCNX -
Yale Door Closer 3301
The Yale Door Closer 3301 is constructed of a cast aluminum alloy. It is considered a Grade 1 Closer, which is the highest grade possible. The closer features an adjustable spring tension, and separate closing, latching and back check intensity valves. The slim line plastic cover is standard on this closer. This door closer replaces the older 3301BF closers. The new version is Barrier Free Complaint. The hole spacing is 3/4" x 12", the cylinder is sometimes cast 20-3301-1001 on the back of the cast aluminum cylinder. This closer ships with all of the mounting hardware and parallel arm bracket.
3300- -
Bilco Barracuda DSI for In Swinging Doors
The Barracuda DSI is designed for In Swinging 36" Doors. The user places the deive on the floor and slides the metal plates under the door. Then pushing outward on the handles engages the plates to the exterior door jamb. Then you simply install the locking pin to barracade the door. The device is manufactured of heavy-duty steel that is then coated in a durable powder coat paint. It will work on just about any door and comes in 6 different versions depending on your jamb width. It is lightweight and comes with a storage mounting rack, along with all the the needed hardware for installation.
Barracuda Part Number
4-3/4" DSI-2
5-3/4" DSI-1
6-3/4" DSI-3
7-3/4" DSI-4
8-1/4" DSI-5
8-3/4" DIS-6DSI -
Floor Door Stop-Security FS18
Floor Door Stop-Security FS18 is designed for areas of high vandalism. The molded rubber is flame resistant and mounted to a 5/8" threaded mounting shaft. Once the 7/8" diameter hole is drilled to a depth of 2-1/2" it can be grouted in concrete and leaves no exposed fasteners. The recommended grout is Thorogrip. They are ideal for jail or security cell areas. There are two versions of this door stop one projects 1-1/2" (FS18S) out of the floor and the other 3" (FS18L).
GFS18- -
Corbin Door Closer 100/110/120
The Corbin 100, 110 and 120 Door Closer are no longer available. They have been replaced by the DC6210, which has the same hole spacings and arm. You will not have to redrill or modify your door to make the DC6210 work in place of your existing 100, 110 or 120 door closers. The DC6210 has a little bit larger body due to the increased functionality of this closer. This new closer will meet all the ADA requirements.
Corbin Russwin’s history combines high-quality product and innovative design. That tradition continues with the new Grade 1 DC6000 Series door closer, designed and engineered with quality features such as captured valves and a complete range of new arms. The DC6000 series is the perfect closer for high-use openings or openings that must meet ADA requirements, such as schools, office buildings, health care facilities, and retail complexes. The series also meets UL and UL10C positive pressure requirements for fire openings.
Uses the same mounting bracket as the 100, and 2800 series.Older models may have SL72 or MS93 cast on the cylinders. You may also find Clarksdale, MS cast on the cylinder also.
DC6210b -
Jackson Door Closer Offset Arm - 20-1312-LC
The Jackson Door Closer Offset Arm - 20-1312-LC is the replacement arm and track for the Jackson 20-330 Door Closer. The track measures 12-7/8" long by 1/2" thick, and the arm has an overall length of 12-15/16" long with an offset of .826". This set is for use with single acting doors with a 3/4" offset. Package includes the arm and track.
Jackson part # 20-1312-LC
G201312LC