The Von Duprin 970321 299 Strike Shim is for use with the Von Duprin 299 and Falcon FA299 strikes. The plate measures 2-7/8 x 1-1/4" x 1-16" thick. The product is sold individually.
The Von Dupin 1439 Strike measures 1-7/8 horizontal x 1-3/4 inches vertically. The strike has a projection of 1/2 inch. We find this strike used on the 33A and 35A exit devices.
The Von Duprin 050580 Weather Stripping is for there 5654 and 5754 Mullions. Each strip is 10' long and two would be required per mullion. This product is specific to Von Duprin products and will usually only work on Von Duprin Products.
The Von Duprin 900894 230L Tailpiece Auxiliary includes the Tailpiece (steel), Tailpiece Guide (nylon), and the Pine Tree Clip (nylon). The Tailpiece measures about 2-1/2" x 1/4" x 3/32" thick.
The Von Duprin 3348/9948 Top Latch Kit 050494 is used on the 33A, 35A, 98 and 99 exit devices. Replaces all previous versions of the 33/3548 and 98/9948 top latches.
Von Duprin Part # 050494 Von Duprin Old Part # 112906
Von Duprin 88 Dog Screw. Newer style, after 1975 or so. If you have an older exit device they no longer make that screw. I would recommend the D100, Panic Bar Retainer, for dogging down your device.
The Von Duprin 900620 35/3348 98/9947 Adjusting Screw Package is used to adjust the concealed vertical rods. This package is used on the 3347, 3547, 3347-F, 3547-F, 9847, 9847-F, 9947 and 9947-F. This is a package of 2.
The Von Duprin 338 Strike measures 1-5/8" by 1-7/8" with a 5/8" projection. The screw mounting is 1-7/8". This strike is used as a bottom strike on the Von Duprin surface and standard equipment there concealed vertical rod devices 3347, 3547, 5547 8847, 9847 and 9947.
The Von Duprin 8827 Bottom Latch Case 050461 is used on all Von Duprin 8827 non fire rated exits. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. Included mounting screws.
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
The Von Duprin Panic Device 230NL Trim is for use with the 22 Rim and 2227 Surface Vertical Road devices. The key locks and unlocks the panic bar. The plate measures 3" wide by 12-1/16" high and has a plate thickness of 3/32".
The Von Duprin 050709 Dogging Assembly is used to update the Von Duprin 22, 33, 35, 98 and 99 device shipped before 1997. The dogging key on this assembly is 5/32", and you would want to use the longer version of our 88R60 dog key.
New style axle snaps together, and replaces the old style which were screwed together with allen wrenches. This style of axle has been around since about 1990. The piece on the right is only used for taking the axle apart.
The Von Duprin 090039 is used in the push bar assembly to return the latch. It is known as the Base Plate Latch Return Spring or Latch Return Spring. It is used on the 22, 33A, 35A, 98 and 99 Devices. The spring is 2-1/4 inch long with a 3/8 inch diameter.
The Von Duprin Exit Device 5547 Blind Fastener Kit 900539 is used to connect the Rod Control Housing to the Rods. This part is used on the 5547 Concealed Vertical Rod only.
The Von Duprin 55 Center Case Axle 090050 is used on the Rim Panic Hardware only. The Rim device is one that has a latch bolt sticking out of the housing.
The Von Duprin 050508 88TP-F Cylinder Cam Package is the piece that the key cylinder fits into on the back of the exit device. This piece is only used with the 880TP outside trim on the Rim Devices.
The Von Duprin Old Style Dogging Shaft was used on devices manufactured before July 1997. The Shaft measures roughly 1-1/2" long with a 1/2" diameter. The hex is 5/32".
The Von Duprin Strike 299 is used on the 22, 88, 98, and 99 Rim Devices and also as a Top Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 299 strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". Ships with shim and mounting screws.
The Panic Hex Key 5/32" x 3-1/16" Long is a must for Von Duprin 22, 33, 35, 98 and 99 panic hardware. This key has a longer shaft to reach deeper into the Von Duprin Panic Devices. This key is also known as Hex Key, Dog Key, Allen Key, and Dogging Key.
The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.
Von Duprin Part # 050328 Old Von Duprin Part # 967616
The Von Duprin 88 Center Case Rivet 090002 is also known as the Latch Tail Rivet used on the 88 Rim Device. The Rivet fits into the spring and into the Latch Tail 050500. The rivet measures 1-1/4 inches long less the head, with a 1/8 inch diameter. We sell this piece individually.
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
The Von Duprin Dogging Adapter 090043 is the piece that the 090042 and 090040 fit through and lock in place. These piece very rarely has to be replaced. The Shaft 090040 is usually the part you need to replace. We sell these individually.
The Von Duprin Exit Device 2227 Center Case 109358 replaces worn out Von Duprin 2227 Surface Vertical Rod Center Cases. The center case has been the same for the last 30 years.
Von Duprin Part # CASE.107 Old Von Duprin Part # 109358
The Von Duprin 3348/9948 Bottom Latch Kit 050495 is used on the 33A, 35A, 98 and 99 exit devices. Replaces previous versions of the 33/3548 and 98/9948 bottom latches.
Von Duprin Part # 050495 Von Duprin Old Part # 112907
The Von Duprin 2227 Top Latch 050091 latch is used on devices shipped before October 1998, see related products for the new style latch if your device is newer. This is usually the problem if your bottom rod is dragging on the floor. Latch measures: 1-1/16" wide x 4-5/16" long (less latch bolt) x 1-7/8" projection at the highest point. Includes screws.
The Von Duprin 1654-4954 Mullion Brackets 050330 are the top and bottom mullion fittings for the 1654 and 4954 Mullions. . Includes Top and Bottom Fittings, screws and mounting shields.
The Von Duprin Panic Device 55 Center Case 050183 is a replacement housing for the 55 Rim Device. The housing includes all of the internal workings and latch bolt. Von Duprin Part # 050183.
