Search results for: 'dorma sizing door cast dogged made von'
-
Door Pull Handle 11
The Door Pull Handle 11 has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.
GHE11- -
International Door Closer 5510S Rim Device
International 5510S Rim Device-Light Duty
All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steelStandard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.5510S- -
Back to Back Offset Door Pull 1.25 inch
Back to Back mounted Off-Set Door Pull featuring 1-1/4 inch stock diameter stock. Handle has a 4 inch offset with a 2 inch clearance and 3 1/4" projection. Available in 12 or 18 inch centers. Sold as sets, 2 handles and 3/8-24 thread stud.
Back to Back fasteners are for a 1-3/4 inch thick door, if your door is a different thickness, please let us know in the comments.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GHEM39xM39 -
LCN Sentronic Closer 4040SE
The LCN 4040SE Sentronic Door Closer is a heavy duty, non-handed, non-sized closer/holder designed to provide single point hold-open for fire and smoke barrier doors. The door is held open until current interruption releases the holding mechanism and the door closes. Single lever (track) arm closer is specifically designed for interior doors. Choice of finishes, track functions, and installation accessories meet virtually all life safety requirements. The SE stands for Single Point Electronic, with this closer the hold open point can only be one point, so the closer has to be positioned on the door to get the proper hold open point.
This technology has been around since 1972, but back then you would order the 4110SE or 4010SE. These were application specific closers, so you had to specify the hand of the door, door size, and the type of mounting. If you do have an older version, the 4040SE will replace it.
4040SE -
Wall Door Stop / Holder WS45
The Ives Wall Door Stop / Holder WS45 was introduced about 50 years ago as the Glynn-Johnson W45A or GJW45A. When they were purchased by H.B. Ives, it became the WS45. They are constructed of cast Brass or Bronze and then plated to the desired finish. This door stop is unique because the wall does not have to be parallel to the door for it to latch and hold the door open. Spring loaded roller rides up the face of the strike, seating itself on the strike, holding the door firmly in the open position. A heavy rubber pad cushions the shock and absorbs the sound. With unit mounted on door and the strike on wall, vertical adjustment is available on body. The strike is adjustable 45 degrees left or right, both adjustments easily accomplished at time of installation or at a later date. WS45 strike is furnished with wood screws for drywall mounting.
GJW45A- -
Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6 -
Russwin Door Closer 2800/2810/2820
The Russwin 2800, 2810 and 2820 are no longer available. They have been replaced by the Corbin Russwin DC6210, which has the same hole spacings and arm. You will not have to redrill or modify your door to make the DC6210 work in place of your existing 2800, 2810 or 2820 door closers. The Corbin Russwin DC6210 has a little bit larger body due to the increased functionality of this closer. This new closer will meet all the ADA requirements.
Corbin Russwin’s history combines high-quality product and innovative design. That tradition continues with the new Grade 1 DC6000 Series door closer, designed and engineered with quality features such as captured valves and a complete range of new arms. The DC6000 series is the perfect closer for high-use openings or openings that must meet ADA requirements, such as schools, office buildings, health care facilities, and retail complexes. The series also meets UL and UL10C positive pressure requirements for fire openings.
Uses the same mounting bracket as the 100, and 2800 series.Older models may have SL72 or MS93 cast on the cylinders. You may also find Clarksdale, MS cast on the cylinder also.
DC6210a -
Von Duprin Panic Device 99 Lever Trim
The Von Duprin Panic Device 996L Lever Trim has an escutcheon plate that measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". The key cylinder, not included, locks and unlocks the lever. This lever handle is handed, but is field reversible. Key lock and unlocks lever. We ship the 996L-R&V
99L -
Door Push Plate 50
The Door Push Plate 50 is the most common push plate we find out in industry today. It does not matter what type of commercial building you go into, you will find this style and thickness plate. The are offered in standard sizes, that are shown below, and can be made to custom sizes. The plates are 16 gauge metal (.050 thick) and are shipped with 4 beveled edges. The matching finiish screws are shipped with each plate.
3 x 12" GPH312
3.5 x 15" GPH315
4 x 16" GPH416
6 x 16" GPH616
4 x 20" GPH420
8 x 16" GPH816GPH50 -
Von Duprin 050500 88 Latch Tail Kit
Von Duprin 050500 88 Latch Tail Kit
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
Von Duprin Part # 050500
G050500 -
Oil Rubbed Bronze Door Kick Plate
Our Dark Bronze Oil Rubbed Bronze Door Kick Plates (US10B) are a baked on powder coat on brass base metal. We switched to this finish 5 years ago due to color variations in the US10B Oil Rubbed Bronze finishes. The US version was much lighter than the Asian version, which is where most the door hardware is made these days. The cost of Oil Rubbing was going through the roof and many platers were having issue with the environmental impact and EPA regulations in the United States. Our Oil Rubbed Kick Plates are 16 gauge (.050″) thick.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut dark brown screw. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates, it is not recommended. Large plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. You can glue them on, I would recommend liquid nails, and some C Clamps with the door on saw horses.
Custom sizes available starting around $0.49 per square inch depending quantity
Please allow 2 week shipping time
GKP-DB -
Sargent Door Closer 1431
The Sargent Door Closer 1431 is also known as the Powerglide. This closer meets ADA requirements and has a capability to be mounted on the push, pull or top jamb, and is non handed. This closer can be used as a direct replacement for the older version 1230 or 1231 Sargent Closers without having to re drill the mounting holes. This closer has been the replacement for the 1230 since about 2000. It is manufactured of an aluminum alloy.
Retrofits existing SARGENT 1230/1231 Series Closer installations
1430- -
Hands Free Foot Operated Door Pull
The Hands Free Foot Operated Door Pull is a low cost solution to keep your hands off of high traffic handles. It is constructed of cast aluminum, and measures 4" wide by 1-7/32" high with a 2-3/8" projection. The package includes fasteners, door decal and installation tool.
G131520 -
Corner Guards-Clear Plastic 313 - 2-1/2" X 2-1/2" X 48"
The Clear Plastic Corner Guards 313 are a good way to protect corners from hand carts and dollies in areas of lighter traffic. If the area has a lot of traffic, like a warehouse, I would recommend the 310 or 311 which are made of metal. The are 2-1/2" by 2-1/2"" and are usually 48" long, but we can do custom sizes. They are constructed of .120" thick clear polycarbonate plastic. Screws are included for mounting.
GCG313 -
Wall Door Stop WS65
The Ives Wall Door Stop WS65 is one of the most economical door stops we sell that is still commercial quality. They are constructed of burnished cast aluminum. The WS65 has a base diameter of 1-5/8" and a 3-3/4" projection. The rubber tip is replaceable. This stop comes with the mounting screws.
WS65 -
Von Duprin 9927 Bottom Latch 050090
The Von Duprin 9927 Bottom Latch 050090 replaces and updates all 9827 and 9927 bottom latches to the new style, if your device was installed before October 1998. If your device is newer then October 1998, then use the G050401. Mounting screws and bracket are included.
Von Duprin Part # 050090
G99VR55 -
Von Duprin Panic Device 7500 Mortise Body Only
This Von Duprin Panic Device 7500 Mortise Body Only is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.
Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.
We ship the 7500 in US32D, brushed stainless steel.
G7500 -
Finger Protector For Doors - Exterior Push Side
Door Finger Protector - Exterior Push Side
This model is specifically designed for exterior doors on the push side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts
Our part # on this is GFG5 for the 78" length, and GFG5+ for the 83" length.
GFG-C -
CRL PR80 Adjustable Spring Door Closer
All PR80 Closers are UL listed and warranted for ten years. Parallel Arm Brackets and mounting hardware are included with each closer permitting universal installation for regular, top jamb or parallel arm applications. The closer is supplied with a standard plastic slim style cover.
The closer is sized for 2 to 5 spring tension and will work on doors 24" to 54" Wide and 33 to 264 Lbs. This closer has a hole spacing of 3/4 x 9-1/16 inches.
PR80-
