Search results for: 'fire door parts american device H-1'
- Related search terms
- door series 30 push bar panic exit deg parts 1306
- door series 30 push bar panic exit dor parts 1311
- door series push bar panic exit dor cal parts 1307
- door series 30 pull bar panic exit dor parts 1310
- door series 30 push bar panic exit dent parts 1306
- door series 30 pull bar panic exit detex parts 1306
- door series 30 pull bar panic exit deep parts 1308
- door series 30 pull bar panic exit dead parts 1306
- door o matic 1 panic device 1309
- dooramatic door series 30 push bar panic exit devic parts 1315
-
Von Duprin 6112 24 VDC Electric Strike
Von Duprin 6112 24 VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The 6112 has a 3/4” latch bolt throw, 9” face plate length, 1-5/8” width, and an 1-3/4” backbone depth. The lock retrofits the Folger Adams FA 310-4. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6112 -
Von Duprin 8827-F Top Latch Kit 050462
The Von Duprin 8827-F Top Latch Kit 050462 is the Top Latch Kit for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted postion.
Von Duprin Part # 050462
Old Part # 10267688VR10F -
Von Duprin Strike 1609
The Von Duprin Strike 1609 strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the Von Duprin 22/2227, 88/8827, 98/9827 and 99/9927 combinations. The strike base measures 1-1/16" wide by 3-1/4" high, the lip projects out 7/8". The three slots are 1-1/4" on center. This strike ships with the mounting screws. This Strike is not rated for Fire Doors, which are usually interior corridor doors.
Von Duprin Part # US19-Black finish
1609 -
Von Duprin Strike 299F
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
Von Duprin Part # 299F
299F -
Von Duprin 9975 Panic Device Only
Von Duprin 9875/9975 mortise lock device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4-3/4" (121mm). The Von Duprin 9875 device has a smooth mechanism case and the Von Duprin 9975 device has a grooved case. The mortise lock device is non-handed
9975EO -
Ives FB458 Metal Door Flush Bolt
Ives FB458 Metal Door Flush Bolt
The Ives FB458 is a UL Listed Flush Bolt for use on Fire Doors. The face plate measures 1" wide by 6-3/4" long with a depth of 1-1/8". Hole spacing is 1/2 inch by 6-1/4 inches on centers. The bolt has a 3/4" throw and is 1/2" diameter. This Flush Bolt is available in Polished Brass, Oil Rubbed Bronze (dark brown) and Brushed Chrome. We try to stock the 12" rods, which are standard, but we can also get 18", 24", 36" and 48"
Ives Part # FB458
FB458- -
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The model 6111 retrofits model number VD 3031, and measures 1-5/8” wide, 6” high and has a backbox depth of 1-3/4”. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6111 -
Monarch 19-V Exit Panic Device
Monarch 19-V Exit Panic Device
- Hand: Field reversible.
- Functions: All functions built into “EO” device.
- Finishes: Powder-coated aluminum–SP28; powder-coated duranodic–SP313;
- Latchbolt: Top stainless steel 3⁄4" throw. Bottom square bolt 1⁄2" throw.
- Deadlocking Latchbolt: Standard.
- Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
- Stock Sizes: 3'0" and 4'0"
- Doors: 13⁄4" thick, wood or metal.
- Narrow Stile Doors: To 1-3⁄4" N.S. aluminum. With control trim–2-1⁄4" min. stile.
- Projection: 2-1⁄2" max., 1-7⁄8" dogged.
G19VEO- -
Adams Rite 8800 Panic Device
Adams Rite 8800 Panic Device
The 8800 features the Starwheel locking bolt that interlocks door to the door frame. The 36" version is in stock, we can also get the 30", 42" and 48" devices, lead time is 2-3 weeks. This device is used exclusively on aluminum framed glass storefront doors. Replacement parts are available.
8800EO- -
Von Duprin 050500 88 Latch Tail Kit
Von Duprin 050500 88 Latch Tail Kit
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
Von Duprin Part # 050500
G050500 -
Corbin Russwin 650F36-8 ED5200A Active Head
The Corbin Russwin 650F36-8 ED5200A Active Head used on the Corbin Russwin ED5000 Rim Device, for fire rated doors. For non fire rated doors, order the G650F35-8. A fire rated door is a door were you can NOT use your allen wrench to dog, or lock, the door in the open position during business hours.
Corbin Russwin part # 650F36-8
G650F36-8 -
LCN Sentronic Door Closer 3130SE
The LCN Sentronic Overhead Concealed Door Closer 3130SE is shipped with a standard arm, 24V or 120V SE track (please specify), track roller, and wood and machine screw pack. Sized cylinders for interior doors to 4’0”. Functions as full rack and pinion door closer when hold-open is not engaged or current is interrupted. Handed for right or left swinging door. Interfaces with fire alarm systems.
LCN Sentronic Door Closer 3130SE parts are also available.
3130SE -
Floor Door Stop FS442
Floor Door Stop FS442
This Floor Mounted Door Stop used to go by the name Glynn Johnson GJFB19 or FB19. When Ingersoll Rand purchased H. B. Ives in the 1990's they brought it over under the Ives Floor Mounted Door Stop FS442. Features: Designed to blend well with all types of construction and provide a minimum of hindrance to cleaning efforts. Accommodates door undercut up to 2". Heavy-Duty cast brass or aluminum construction. Non-marring rubber bumper. This door stop has an overall height 2-7/8". Mounted shield and screws included.
GJFB19- -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606- -
Cal-Royal 45 Narrow Stile Rim Device
The Cal-Royal 45 Narrow Stile Rim Device is part of the new 4500 Series. They are designed for Narrow Stile doors with a minimum of an 1-3/4" stile width. This is a Grade 1 Exit Device, which is the highest traffic rating possible. Exit device ships with strike and mounting screws.
Shown is Left Hand Reverse
Opposite would be Right Hand Reverse45-RIM -
Corbin Russwin ED5400 Panic Device
Corbin Russwin ED5400 Exit Device
Handing
Device is handed but easily field reversible.
Lever trim is handed.
Bar Length
Easily field cut to size.
Standard: 36" (914mm) bar fits 30"- 36" door.
Door Thickness
1-3/4" (44mm) standard.
Stile
Minimum width 4-1/2" (114mm).
Door Height
Standard top rod for 7' door.Replacement parts are also available
ED5400 -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Jackson Panic Device 20-1266 2085/2095 End Cap
Jackson Exit Device 2085/2095 End Cap
The Jackson Exit Device 2085/2095 End Cap measures 3-1/8" high, by 1-1/8" wide, and has a projection of 1-15/16". The mounting lugs are 1-3/8" on center and project out 1".
Jackson Part Number 30-1266-628 Aluminum
Jackson Part Number 30-1266-313 Dark BronzeG301266- -
Von Duprin 8827 Bottom Latch Case 050461
The Von Duprin 8827 Bottom Latch Case 050461 is used on all Von Duprin 8827 non fire rated exits. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. Included mounting screws.
Von Duprin Part # 050461
Old part # 10175188VR170 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
Dor-O-Matic 2090 Panic Device
The Dor-O-Matic 2090 Panic Device has been around since the early 1970's. Even though it is now called the Falcon 2090 Panic Hardware, it is the same exact device. The 2090 provides balanced appearance, dependable performance and economical pricing, making it a popular choice where rim exit devices are required. The package includes both housings, 41" crossbar (that can be cut in the field), mounting screws and strike.
Hand: Specify RHR or LHR, not reversible. See Below
Left Hand Reverse shown in picture
Latchbolt: 1/2" throw hardened steel.
Dogging Feature: Hex dogging standard.
Sizes: Field adjustable width, 41" crossbar standard, fits
3' 8" door width, extra length crossbars available.
Doors: 1-3/4" thick metal or wood doors, specify if wood door.
Projections: 4-3/8" extended, 2-1/2" depressed.
Stile: 1-3/4" minimum.Replacement parts are also available
G2090EO -
Rixson 27 Series Door Closer
• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustmentWhen Less All Parts is selected only the Cylinder is shipped, just the replacement hydraulic cylinder will be shipped
27-RIX -
Floor Door Stop Dome 1" Height FS436
Floor Dome Door Stop 1" Height FS436
We ship the H.B. Ives FS436 Floor Dome Stop, another product made by Ives that has been around for 50 plus years. Take a walk around a school made in the 1960's and you will probably find this door stop, or the hole were it used to be. This Dome Stop is used on doors without thresholds that have a bottom of the door to floor clearance of less than 5/8". The are constructed of cast aluminum or cast bronze depending on the finish you are looking for. The rubber stop is non-marring and replaceable. The stop has a base that is 1-3/4" x 2" oval, an overall height of 1" and a base height of 3/16".
GJFB13- -
Corbin Russwin ED4200 Panic Device
Corbin Russwin ED4200 Narrow Stile Exit Device
This device is designed for use with a narrow framed glass door, and is recommend for use in high traffic, abusive areas.Device
non-handed.
Trim handed.
Easily field cut to size.
Standard: 36" bar fits 30"- 36"
914mm) door.
Stile
Minimum width 2" (51mm).Replacement parts are also available
ED4200- -
Monarch 912L Panic Device Lever Trim
Monarch 912L Panic Device Lever Trim
The Monarch / Falcon 912L Lever Trim is for use on the Monarch / Falcon 19 Series. The 912L measures 7-1/4" high by 1-3/4" wide and the mounting plate is 5/8" thick. We ship these with the Dane Lever, which projects out 2-7/8" in the Classroom function. On the Classroom function the key locks and unlocks the lever handle, the Key Cylinder is not included. We offer this Lever Trim in Painted Aluminum, Painted Dark Bronze, and Brushed Satin Nickel.
Monarch Part # 912L Dane
G912L-