Search results for: 'half case pull plate guid'
-
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558 -
Falcon 650233 24-R Center Case
Falcon 650233 / 650234 24-R Center Case
Replacement Center Case for the Monarch-Falcon 24-R Narrow Stile Rim Device. This Center Case is for use on both the Fire Rated and Non Fire Rated devices. This was changed in the summer of 2018. The 650233 has been replaced by the 650234, which was the Fire Rated version part number.
Falcon Part # 650233 / 650234
G24R15 -
Door Push Plate 61
The Door Push Plate 61 is constructed of 16 gauge stainless steel, aluminum, brass or bronze. This plate is handed left and right, the one shown on the website is a Left Hand plate. They measure 7-1/2" wide by 15" long, and ships with the matching finish mounting screws.
GPH61 -
Von Duprin 88 Active Case 050409
The Von Duprin 88 Active Case 050409 is for use with the Rim Device, which is the model that has the latch bolt sticking out the side of the housing. This version of the housing is for use on the 88EO (Exit Only), 88DT (Dummy Trim) and 88NL (Night Latch) models only. Call or email if you need the Thumb Piece, Knob or Lever Version. The Center Case includes all of the internal workings.
Von Duprin Part # 050409
Old Part # 10166288R10- -
Anodized Black Aluminum Door Kick Plate 315AN
The Anodized Black Aluminum Door Kick Plate 315AN are a flat black and match the black color we find on Storefront doors. These plates have an aluminum base metal, which is 18 gauge (.040") thick that is then Anodized in the Black Color. These plates relatively inexpensive. Custom sizes are available, they run about $0.25 per square inch.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
GKP-BLK -
Jackson Panic Device Center Case 1085/1095
The Jackson Panic Device Center Case 1085/1095 is for use with the 1085 devices for both and left, and the inactive case of the 1095. Case is easily removed by loosening the two 1/8" Allen screws and one on the bottom. Includes everything in the housing. The distance between the mounting studs on this Case is 6-5/16"
Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm AssemblyHousing Shown in Aluminum
G1085XX -
Hands-Free or Foot Door Pull BM46
The Hands-Free/Foot Door Pull BM46 can be used as a ADA compliant hands-free door pull when mounted 42" above the finished floor. Or as foot pull when mounted at the bottom of the door. The Pull is 4" x 5" and is made of .090 thick stainless steel. Ships with sex bolts and screws for 1-3/4" door. Available in Brushed Stainless Steel, Flat Black Powder Coat and Dark Bronze Powder Coat.
GBM46- -
Von Duprin Panic Device 8827 Center Case 050415
The Von Duprin Panic Device 8827 Center Case 050415 is for use on the non fire rated 88 surface vertical rod. You can tell the difference by the dogging screw. If you have a Dogging Screw on your device, then this is the correct part. Includes the internal pieces, including the Rod Control.
Von Duprin part # 050415
88VR120- -
Doromatic Exit Device 2090 Active Case
The Doromatic Exit Device 2090 Active Case is for use on the 1090 and 2090 panic hardware. This device has been around since the early 1970's, and is now called the Falcon 2090 Active Case, but it is the same piece. Includes all of the interior hardware. Just unscrew or loosen the three set screws and remove your old case and install and tighten the three set screws. Housing measures 7-1/2" long by 1-3/16" wide, mounting studs have a 6-1/4" center to center distance.
LEFT HAND HOUSING SHOWN IN PICTURE
4270902740 Left Hand Aluminum Stock
4270902742 Left Hand Dark Brown Stock
4270902743 Left Hand Black * One week lead time
4270902746 Right Hand Aluminum Stock
4270902748 Right Hand Dark Brown Stock
4270902749 Right Hand Black * One week lead timeG209001 -
Door Pull Handle 11
The Door Pull Handle 11 has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.
GHE11- -
Lifetime Polished Brass Door Kick Plate
The Lifetime Polished Brass Door Kick Plate has a 16 gauge (.050″ thick) base metal, that is then plated with a artificial brass finish that is then polished. The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD. Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish. The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates.
Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″. You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes, but they are made of Stainless Steel, which is a tough metal to drill. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.40 per square inch depending quantityPlease allow 1 week shipping time
GKP-US3-PVD -
Door Pull Handle 16
The Door Pull Handle 16 has an overall length of 7-1/2". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.
GHE16-
