Search results for: 'heavi cycl push plate good'
-
Detex D Lever Trim for 10 Series
The Detex D Lever Trim is used on the 10, 20, 21 and 27 Series exit devices. The D Lever is designed to be as heavy duty as their exit devices. It features a break-away lever to prevent damage. The escutcheon measures 2-3/4 x 9-1/16 inches, with a plate thickness of 7/8 inch. We ship the classroom function, which locks and unlocks the lever.
G08DS- -
LCN 4410HSA Sentronic
The 4412HSA SENTRONIC® is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Double lever arm closer is specifically designed for push side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.
4410HSA -
Reinforcing Pivot Hinge 4-1/2"
Reinforcing Pivot Hinge - For use with 4-1/2" wide butt hinges
3/4" to center line of 4-1/2" hinge pin.
Pin uses large pin and bushing.
Used to dampen vibration and increase
strength to your full mortise butt hinges.
Constructed of heavy duty cold rolled steel.
Made of Zinc Plated Steel
Supports weights up to 300 lbsManufacturer part # B1923
Our part # DR1923 for Right Hand, DL1923 for Left HandThese hinges are no longer handed, you can select right or left, but the hinges will work both ways.
B1923 -
Sargent 2727 Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warranty2727EO- -
Ives Surface Bolt 8" SB453
The Ives Surface Bolt 8" SB453 has a 1-3/16" throw. The bar has a cross section measurement of 3/4" wide by 1/4" thick. It features a strong tension springs to prevent the bolt from creeping. The bolt is shipped with all of the fasteners and a universal top and a standard mortise strike. It is constructed of heavy duty steel that is then cadmium plated.
Ives part # SB453-8-TB-2C
GSB82C -
Sargent 2828 Series Rim Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warrantyG20EO- -
Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3- -
Dor-o-Matic 1590 Panic Device
Effective December 20, 2024 Falcon Doromatic has discontinued this exit device. They are currently working on retro-fit plates to make transitioning to 1790EO more easily.
The Doromatic 1590 is our heaviest device and offers a clean appearance with pushpad styling and a variety of practical features. The Doromatic 1590 is built with rugged steel operating mechanisms, and durable aluminum push bars and end caps.
Replacement parts are also available
Shipped with all screws and strikes.
1590EO- -
Wall Door Stop / Holder WS45
The Ives Wall Door Stop / Holder WS45 was introduced about 50 years ago as the Glynn-Johnson W45A or GJW45A. When they were purchased by H.B. Ives, it became the WS45. They are constructed of cast Brass or Bronze and then plated to the desired finish. This door stop is unique because the wall does not have to be parallel to the door for it to latch and hold the door open. Spring loaded roller rides up the face of the strike, seating itself on the strike, holding the door firmly in the open position. A heavy rubber pad cushions the shock and absorbs the sound. With unit mounted on door and the strike on wall, vertical adjustment is available on body. The strike is adjustable 45 degrees left or right, both adjustments easily accomplished at time of installation or at a later date. WS45 strike is furnished with wood screws for drywall mounting.
GJW45A- -
Roller Bumper Straight Arm 4" RB471
The Ives Roller Bumper Straight Arm 4" RB471 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 4-1/2" and the base has a 2" diameter. The device was just like the Glynn-Johnson RB4 or GJRB4.
GJRB4- -
Plunger Type Door Holder / Stop 583
The Plunger Type Door Holder / Stop 583 is constructed of solid cast brass, that is then plated to the desired finish. It measures 5-3/8" by 2-1/4" base with a 1-1/4" projection. The throw is 1-1/4". These are sometimes called pop-up or push down stops. This piece will ship with matching finish mounting screws.
GJ583- -
Dor-o-Matic 1690/1790 Push Bar Pin PB322
Dor-o-Matic 1690 and 1790 Pushbar Pin
Doromatic part # PIN.128 or PB322
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts BreakdownGPB322 -
LCN 4040XP Rw/PA Door Closer
The 4040XP Rw/PA is LCN’s most durable and flexible heavy duty surface mounted closer, designed for institutional and other demanding high traffic applications. The LCN 4040XP Rw/PA sets a new standard for reliability, longevity and value with a better design and extraordinary performance testing that goes far beyond industry requirements. They built the 4040XP from the inside out, combining tougher, bolder construction with proven LCN technology. The result is a closer that’s stronger, smarter and delivers remarkable value in a variety of applications.
The patented green dial on the LCN 4040XP Rw/PA makes spring adjustments fast, easy and foolproof. The all-weather fluid reduces maintenance and ensures consistent performance through every season. High-traffic doors call for heavy-duty closers – closers that won’t let you down no matter how many people go through the door or how hard they kick, push or slam against it, or in the case of public schools the dreaded flying kung-fu kick. And when it comes to heavy-duty closers, no other closer performs like the LCN 4040XP Rw/PA.
The LCN 4040XP Rw/PA features cast iron construction, forged steel arm, double heat treated steel pinion, non-handed, LCN® “Green Dial” spring force indicator, Peel-n-Stick templates, UL and cUL Listed, 3⁄4″ journal diameter pinion, full compliment bearing, and tested and certified under ANSI standard A156.4, Grade 1.
4040XP- -
Cal Royal Products 800 Door Closer
The Cal Royal Products 800 Door Closer is one of there newer closers. The CR801 has a hole spacing of 3/4" x 12" and ships with either a full cover or slim cover. The full cover will hide both spindles, were as the slim cover will not. This closer is a Grade 1 closer, the heaviest rating possible. The cylinder has adjustable spring tension, closing, latching and back check speeds. It can be mounted on the push, pull or top jamb. The CR801 will work in place of the Norton 8000 and Yale 3000 series door closers, with no new drilling.
CR801S - SLIM COVER
CR801 - FULL COVER
Ships within 24 hours from California.
CR800- -
Sargent Door Closer 351
The Sargent Door Closer 351 is the most heavy duty closer made by Sargent. This closers meets ADA requirements, meets the Buy American Act, and is certified Grade 1, the heaviest rating possible. The closer has the capability to be mounted on the push, pull or top jamb, and is non handed. It ships with arm, plastic cover, parallel arm bracket and all of the fasteners. The hole spacing is 2-1/2" x 9"
350- -
Wall Door Stop WS11
The WS11 door stop used to be under the Glynn-Johnson product line as the WB11 until they merged with H.B. Ives. At that point they became the WS11. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11x, except that it is designed for wood or drywall mounting and ships with wood screws and anchors.
GJWB11- -
Global DoorTC4361 Door Closer
The Global Door Closer TC4361 is recommended for use on heavy duty commercial, architectrual and institutional applications. It is ideal for business, new construction and renovations. It has a full selection of accessories to accomodate the requirements of any field installation. It is tri-packed standard and comes with all fasteners, brackets and soffit plates for versatility. Closers with non-hold open arms are UL listed for "A" label fire doors. Fully compliant with opening force requirements for ADA and ANSI/BHMA standards.
Options: Specify when Ordering- Finish - AL, DU
The hole spacing is 1" by 7-1/2"
TC4361- -
Cal Royal Products 400 Series Door Closer | Economical Door Closer
The Cal Royal Products 400 Series Door Closer is for lighter use interior doors. This closer is considered a Grade 2, which means it is only rated for 1,000,000 cycles. The 400 Series is a sized closer, meaning you can not adjust the spring tension, the spring size you select is what you get. Also, make sure to note the hole spacing of the various sizes below. These closers also offer adjustable closing and latching speeds.
Size 420 3/4" x 6-5/8" hole spacing
Size SM 430P 3/4" x 6-1/2" hole spacing
Size 430P 3/4" x 8-3/16" hole spacing
Size 440P 3/4" x 8-3/16" hole spacingCal Royal 400 Series Catalogue
400P -
Wall Door Stop WS11X
The WS11X door stop used to be under the Glynn-Johnson product line as the WB11X until they merged with H.B. Ives. At that point they became the WS11X. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11, except that it is designed for a masonry type mounting and ships with an expansion sheild.
GJWB12- -
Wall Door Stop / Holder WS20
The Ives Wall Door Stop / Holder WS20 is another door holder from Glynn-Johnson. The Chicago based manufacture made these for 40 plus years. When they were purchased from H.B Ives and merged into there line they became the WS20. This holder is constructed of cast brass and then plated to your desired finish. The hinged holding clip can be released by a gentle pushing on the door, which causes the clip to flip up and release the door. The piece ships with wood screws and anchors.
GJW20- -
Rixson H180 Top Pivot
• Standard top pivot for heavy-duty offset
pivot sets
• Heavy-duty needle bearings are standard
• Non-ferrous base metal
• 3/4"(19mm) offset (measured from
centerline of pivot to face of door)
• Furnished with wood and machine screwsH180- -
Cal Royal CRCODE101 Mechanical Lever Trim for 7700 and 9800 Exits
The Heavy Duty Cal Royal CRCODE101 is for use on the 7700 and 9800 Rim and Surface Vertical Rods. This lock features Single Code with up to 8000 code combinations, weather resistant, non handed, and code can be changed without removing the lock. Comes in Brushed Chrome finish only.
CRCODE101 -
Falcon / Dor-o-Matic 2390 Exit Device
Effective December 20, 2024 the 2390 has been discontinued. Falcon Doromatic is working on retro-fit plates to work with the 1690.
Doromatic 2390 Exit Device
The 2390 is a Grade 1 exit device designed for high use and abuse, and delivers a variety of performance features that ensure smooth, easy and reliable operation. Easier rod adjustment simplifies installation. This device is for replacment of older worn out Falcon / Dor-o-Matic 2390's. This is not a good exit device to use to replace devices from different manufactures.To order specify:Door Width:42" (Device size has a 21" Touchbar)
48" (Device size has a 24" Touchbar)Color:
Aluminum
Dark Bronze
Device Centerline to Finished Floor Measurement in inches:2390EO- -
Cal Royal ESC6600 Escutcheon Lever Trim
The ESC6600 are non handed, with a Grade 1 thru bolted design. It features a clutch mechanism, double heavy duty spring support to prevent sagging and a hardened stell heavy duty spindle. Entrance function, key locks or unlocks lever, operates as a Classroom Function. Ships with mounting screws and a 6-Pin Schlage Mortise Cylinder.
ESC6600- -
Rixson 27 Series Door Closer
• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustmentWhen Less All Parts is selected only the Cylinder is shipped, just the replacement hydraulic cylinder will be shipped
27-RIX -
Floor Door Stop / Holder
The F20 or GJF20 was a mainstay of Glynn-Johnson for years. When the Glynn-Johnson door stop line merged with H.B. Ives it became the FS20. This door stop has been discontinued from Ives, but we have been able find a large stock. This Floor Mounted Door Stop also holds the door open, when in the latched position you can push the door and the holding latch will flip up and unlock thee holding clip. It is constructed of cast bronze or brass and then plated to your desired finish. This stop has a 2-1/2" long base that is 1-1/2" wide. The overall height is 3-1/8" with a 2-5/16" floor to rubber stop centerline. For use with door undercut up to 2-1/2".
GJF20- -
International Door Closer 8630S SVR Device-Grade 1
International 8630S Surface Vertical Rod Device-Grade 1
DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.
Non handed, 4-1/2" minimum stile width. Smooth Surface.
For doors 29" to 36" wide order the Size 30 to 36"
For doors 36" to 48" wide order the Size 48"8630S- -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
Detex Advantex 40 Series Narrow Stile Rim
The Detex 40 Series rim exit device is a supper heavy duty panic device for use on narrow stile doors. Device features an angled end cap to deflect damage away from the unit. This device is designed for years of trouble free service in high use, high abuse enviroments.
G40REO- -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
Glynn-Johnson Overhead Door Holder 81 Series Surface Mounted
The Glynn-Johnson 81 Series Overhead Door Holder Surface Mounted provide rugged, heavy-duty door control. The jointed-arm design provides the most effective stop mechanism available. The shock absorber bracket is surface mounted, usually with sex bolts. The jamb bracket is mounted to the stop of the frame, so a minimum of door and frame preparation is required.
GJ80 -
Cal Royal Panic Device 2000 Series Lever Trim
Cal Royal 2000 Series Exit Device Lever Trim
Non-handed Grade 1 (Clutch Style)
Cylindrical body hardened steel heavy duty tailpiece. For
1¾” and 2 ¼” doors. Prefix THI before part # for 2 ¼” door
thickness. Available for fire and non fire rated rim and
vertical rod exit devices.
Rose diameter 3 ½”, lever length 4 ¾”.ENTOOL- -
Yale Door Closer 51 Series
The Yale Door Closer 51 Series has been around since the early 1970's. With the advent of the aluminum framed storefront doors, this door closer was a perfect fit. The 50 series is a non-sized, non-handed closer that can be mounted on the push (parallel arm), pull (regular arm) or top jamb. A Grade 1 closer certification, means it is one of the more heavy duty closers out there. Older models may be stamped with Scoville or Eaton, which are the companies that used to own Yale. We some times find 20-0054-4001 or 20-0254-4001 stamped on the back of the closer. Ships with all mounting screws and a parallel arm bracket. The hole spacing is 3/4" by 9-1/16".
50- -
LCN Door Closer 4041XP-CUSH
The LCN Door Closer 4041XP-CUSH is the same cylinder as the 4040XP, but with a CUSH arm (4040XP-3077CNS). This closer can only be mounted in the parallel arm configuration. With this closer you get the XP heavy duty cylinder with the heavy duty CUSH arm.
We ship the 4041XP-CUSH
4040CUSH-