Search results for: '1790 cal jackson panic device block for td door'
-
Falcon Dor-O-Matic STK45 Surface Strike
Falcon Dor-O-Matic STK45 Surface Strike
This strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the 1590, 1790 and 2090 Rim Devices. The strike base measures 1-5/16" wide by 3-1/4" high, and 1/4" thick. The three slots are 1-1/4" on center. This strike ships with the mounting screws.
US19-Black finish
STK45 -
Von Duprin Panic Hardware 210K Knob Trim
The Von Duprin Panic Device 210K Knob Trim is for use on the 22 Rim and 2227 Surface Vertical Rod devices. Key in knob can lock and unlock the knob. Since the enforcement of local ADA standards, this knob is probably at the end of this life, no one seems to want these anymore. The mounting plate measures 3" wide by 4-25/32", and is 3-32" thick. We do have parts on this Knob, but at this point they are not on the website.
220K- -
Falcon Mechanical Electric Latch (MEL) Retrofit Kit 47867200
New for 2024 the Falcon MEL 47867200 Mechanical Latch Retraction. Retrofits all 1690, 1790, 24 and 25 Series devices to Mechanical Latch Retraction. This new system uses the PS902 Power Supply. The benefits for the MEL Series over the Older EL series are lower power draw (1 amp verse 16 amp), and more flexible power supply location, longer wire runs and thinner guage wires.
G47867200 -
Falcon SWITCH.1006 Request to Exit Switch
The Falcon SWITCH.1006 Request to Exit is for use on the Falcon and Dor-O-Matic 1690, 1790 and 2390 devices, produced after June 2002. The Request to Exit Switch allows you to cut the current to various devices when the push bar in depressed.
SWITCH.1006 -
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Von Duprin Panic Device 99 Knob Trim
The Von Duprin 990K Trim is known as a Knob Trim. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The key locks and unlocks the knob. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990K-R&V.
99K-Panic Hex Key 5/32" x 3-1/16" Long
The Panic Hex Key 5/32" x 3-1/16" Long is a must for Von Duprin 22, 33, 35, 98 and 99 panic hardware. This key has a longer shaft to reach deeper into the Von Duprin Panic Devices. This key is also known as Hex Key, Dog Key, Allen Key, and Dogging Key.
88R60Command Access MLRK1-FAL17 Motorized Latch Retraction
The Command Access MLRK1-FAL17 Motorized Latch Retraction Kit With REX is for use on the Falcon Dor-o-matic 1690/1790, AHT4/5, and First Choice 3600/3700 Series Exit Devices. The unit is 24 volt with Standard : 900 mA (Avg Current Peak); 200 mA (Avg Current Hold). The unit requires 18 ga wires. The package includes: 1) Motor Mount with MM5; (1) 50944 Molex Pigtail; (1) 50030 6 Feet Lead with VD Connector; (2) 40124 10-24 x 3/8inch Phillips Screws (Silver); (2) 40125 10-24 x 3/8inch Phillips Screws (Black).
The MLRK1-FAL17 is a cost-effective and straightforward way to upgrade your Falcon 1690/1790, First Choice 3600/3700, & AHT 4/5 series device to motor-driven latch retraction in the field. UL Listed + 3 Year Warranty
MLRK1-FAL17CRL PR90 Door Closer
The CRL PR90 is a Grade 1 door closer, the heaviest rating possible. The template is the same as the LCN 4040 with the same features, latching speed, closing speed, back check and power adjustment from size 1 ADA compliant to size 6.
We offer the Standard Cylinder PR90 and also the Delayed Action PR92. Delayed Action will hold the door open for 15-20 seconds to allow handicap individuals to clear the opening before the door closes.
PR90Falcon / Dor-o-Matic MEL1690 Panic Device
The same as the Falcon / Dor-o-Matic 1690 with Mechanical Electric Latch Retraction. Some of the features are listed below. A power supply is required.
Hand: Field reversible, non-handed.
Centercase and end cap are powder-coated black only.
Strikes: PB48 top.
Latches: Hex bottom latch (standard), RL - rod bottom latch, PL - Pullman bottom latch
Cylinder: Rim, key entry (NL) or hold back (HB) feature available.
Field selectable.
Sizes: 30", 36", 42", and 48".
Doors: 1-3/4" thick metal doors, specify if other.
Projections: 3-3/8" in neutral position, 23/8" in dogged position.
Pushbar height is 2-1/2.
Stile: 1-3/4" minimum.Replacement parts are also available
Shipped with all screws and strikes.
MEL1690EO-Dor-o-Matic 1690 Panic Device
The design of the Doromatic 1690 is ideal for demanding, high-traffic applications. The vertical rods and latch mechanisms are concealed in the vertical door stile, ensuring trouble-free operation. Cast metal cover plates and end caps hold up to rigorous use. A quick, singlepoint dogging feature in the housing deactivates the device, permitting unrestricted traffic flow. The Doromatic 1690 may also be used to retrofit a Doromatic 1990 Series crossbar device.
Replacement parts are also available
Shipped with all screws and strikes. The 1690NL Cylinder Assembly (169CA) is required if you wish to use a key cylinder on the exterior, SEE RELATED PRODUCTS toward the bottom of the page.
1690EOFalcon / Dor-o-Matic EL2390 Panic Hardware
Effective December 20, 2024 the EL2390 has been discontinued. Falcon Doromatic is working on retro-fit plates to work with the MEL1690.
Doromatic EL2390 Exit Device
The EL2390 is a Grade 1 exit device designed for high use and abuse, and delivers a variety of performance features that ensure smooth, easy and reliable operation. We only recommend this device when you have an existing 2390, that your want to control access to with either a card reader or inside button. Easier rod adjustment simplifies installation. This device is for replacement of older worn out Falcon / Dor-o-Matic 2390's. This is not a good exit device to use to replace devices from different manufactures.To order specify:Door Width:42" (Device size has a 21" Touchbar)
48" (Device size has a 24" Touchbar)Color:
Aluminum
Dark Bronze
Device Centerline to Finished Floor Measurement in inches:EL2390EO-International 8710S Narrow Design Rim Device
The International Door Closer (IDC) 8710S is a narrow design rim device. The minimum stile width has to be 2-19/32 inches. The device features a 3/4 inch throw deadlocking latchbolt, hex key dogging, and ships with machine screws and strike. The device is Grade 1 Rated, which is the highest rating possible. The 36 inch device is 33-15/32 long and the 48 is 44-3/4 inches.
8710S-Panic Hex Key 5/32" X 2-1/8" Long
The Panic Hex Key 5/32" X 2-1/8" Long is usually used on Dor-O-Matic, Falcon, Corbin Russwin, Von Duprin 55 and 88 and Yale panic hardware. This Hex Dog Key is not long enough for the Von Duprin 33, 34, 33A, 35B, 98 or 99 Exit Devices. Also known as Hex Key, Dog Key, Allen Key, Dogging Key
88R60-SHORTCRL PR80 Adjustable Spring Door Closer
All PR80 Closers are UL listed and warranted for ten years. Parallel Arm Brackets and mounting hardware are included with each closer permitting universal installation for regular, top jamb or parallel arm applications. The closer is supplied with a standard plastic slim style cover.
The closer is sized for 2 to 5 spring tension and will work on doors 24" to 54" Wide and 33 to 264 Lbs. This closer has a hole spacing of 3/4 x 9-1/16 inches.
PR80-Yale 7100 Series Latch Assy 60-7000-0419-048
Yale 7100 Series Latch Assembly
This latch assembly is used on non fire rated doors, meaning panic devices that you can not dog open with the allen key or key cylinder. Non fire rated doors are usually exterior doors.
Yale Part # 60-7000-0419-048
Note the position of the Hub for this Assembly is the 7100
G6070000419048International Door Closer 200 Series Overhead Concealed Closer
The International Door Closer 200 Series Overhead Concealed Closer has been in there line up for at least 20 years. It is designed as a replacement for the Jackson 20-330 concealed closer. This closer is a fixed spring closer with two adjustment valves, one for closing and one for latching speeds. It has a built in positive back stop and hold open positions, if you order the hold open option. To order select the desired opening swing (90 or 105 degrees) and hold open or non hold open. This is just the hydraulic cylinder, the arms are sold separately.
2000-B-230 105 with Hold Open
2000-B-231 105 with No Hold Open
2000-B-232 90 with Hold Open
2000-B-233 90 with No Hold Open2000-BVon Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611Yale 7100F Series Latch Assy 60-7000-0425-048
Yale 7100F Series Latch Assembly
This Yale Latch Assembly is used on fire rated panic devices. A fire rated panic is a device were you can not lock the latch in the open position. It is used on doors were the engineers want the door to latch every time it closes to contain a fire.
Yale Part # 60-7000-0425-048
Note the Hub Position of this latch is the 7100
G6070000425048Dor-o-Matic Falcon EL1690-EL1790-EL2390 Solenoid
The Dor-o-Matic Falcon 4758959 Soleniod is used on the EL1690, EL1790, and EL2390 Electric Latch Retraction exit devices. The Solenoid measures 4-1/8 inches long including mouting flange, and has an 1-3/4 inch diameter. The mounting screw spacing is 1 inch on centers. The Plunger is included and has a 7/8 inch diameter and is 2-15/16 inches long. We find the number 971687 on the solenoid.
7-1-2025 No longer available. If you have the 1690 or 1790 you can update your exit to the new mortor 47867200
G47639878Monarch / Falcon 24-R Series Rim Exit Device
Monarch / Falcon 24-R Series Rim Exit Device
Robust and aesthetically pleasing, the Falcon 25 Series exit devices provide you a full range of functions and are able to fit narrow and wide stile door types. Falcon is focused on providing you solid products with solid performance at a solid price. The sleek architectural design is perfect for a variety of applications to assure every door opening provides safe egress while also integrating with the overall building design. Combining functionality and design allows you to have confidence that your exit device is built to last and will look great - all at an affordable price.
- Hand: Non-handed.
- Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626);
US32 (629); US32D (630); US28 (628), 313AN. - Strikes: 299 strike standard.
- Latchbolt: Stainless steel, 3⁄4" throw.
- Deadlocking Latchbolt: Standard.
- Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
- Doors: 1-3⁄4" thick, wood or metal. Specify thickness if other than 1-3⁄4".
- Projection: 2-3⁄4" maximum, 2” dogged.
- Mounting Height: 40-1⁄4" from CL to finished floor.
- Fasteners: All mounting screws are concealed, sheet metal screws and machine
screws standard. - ANS I: Certified ANSI A156.3-2001 Grade 1 standards.
- Center Case & Working Parts: Center case is heavy wrought and sintered metal parts.
Call for pricing on non listed finishes
2 week lead time24EO--