Search results for: 'dorma spring door chrome dome main von'
-
Von Duprin Strike 264
The Von Duprin Strike 264 measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.
Von Duprin Part # 264
264 -
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Wall Door Stop / Bumper Heavy Duty Convex WS402CVX
The Ives WS402CVX Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ50C-Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50-Von Duprin 100316 5547 Top Plate
The Von Duprin 100316 is used on the 5547 on the top of the door. The top rod goes through the square hole on the plate. The plate shown in the Picture has both sides or LHR and RHR doors. One side of the strike is usually broken off depending on the hand of the door.
G100316Wall Mounted Door Stop WS33
The Ives Wall Mounted Door Stop WS33 is another hold back part from the Glynn-Johnson door stop era. I can not remember the Glynn-Johnson part #, but when Ives purchased them, they changed it to WS33. This stop is constructed of cast brass that is then plated to a brushed chrome finish. It features a replaceable rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft. And a sloping design that discourages vandalism.The base height is 3" with a width of 2-1/4", and a projection of 3-3/4", WS33 is furnished with wood screws for drywall mounting.
WS33Handicap Door Pull 119
With the Handicap Door Pull 119 you are able to get a closed fist behind the pull, which makes it a great ADA Door Pull. Also known as the Double Arm Pull it is constructed of aluminum, brass or stainless steel stock. It measures 8-1/2" overall length and has 5-1/4" centers on the mounting screws. The flat bar stock is 3/8" x 1", and the round mounting post is 3/4" diameter. Shipped with screws and finish washers. Also known as a Handicap Grip, ADA Door Pull or Handle.
GHP300-Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6Wall Mounted Automatic Door Holder 533
The 533 Automatic Wall Type Holder and Stop is a commercial grade door holder. The holder is mounted on the wall and strike is mounted on the door. It is constructed of cast brass, and measures 2 x 2-1/2 base and 2-1/8 inch high. Currently it is only available in brushed chrome.
GJ533Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3-Rixson Checkmate Overhead Door Holder 9 Series
Rixson Checkmate Overhead Door Holder 9 Series
Product Description & Features
• Doors are single acting
• Non-handed
• Slide track design
• Recommended for high traffic, heavy
abuse installations
• Heavy shock absorber spring provides
5-7° compression before deadstopSize is the Door Width
GR09Wall Door Stop / Bumper Heavy Duty Concave WS401CCV
The Ives WS401CCV Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ60C-Von Duprin 2227/3327/9927 Bottom Latch 050401
Von Duprin 22, 33, 9927 Bottom latch.
Used to replace the bottom latch on the Von Duprin 2227, 3327A, and 9927 on devices shipped after October 1998.
Includes screws and sometimes the bracket
Von Duprin Part # 050401
G050401Von Duprin 9927 Bottom Latch 050090
The Von Duprin 9927 Bottom Latch 050090 replaces and updates all 9827 and 9927 bottom latches to the new style, if your device was installed before October 1998. If your device is newer then October 1998, then use the G050401. Mounting screws and bracket are included.
Von Duprin Part # 050090
G99VR55Von Duprin Panic Device 7500 Mortise Body Only
This Von Duprin Panic Device 7500 Mortise Body Only is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.
Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.
We ship the 7500 in US32D, brushed stainless steel.
G7500Yale Door Closer 3501
The Yale Door Closer 3501 is constructed of a cast aluminum alloy. It is considered a Grade 1 Closer, which is the highest grade possible. The closer features an adjustable spring tension, and separate closing, latching and back check intensity valves. The full plastic cover is standard on this closer. This door closer replaces the older 3501BF closers. The new version is Barrier Free Complaint. The hole spacing is 3/4" x 12", the cylinder is sometimes cast 20-3301-1001 on the back of the cast aluminum cylinder. This closer ships with all of the mounting hardware and parallel arm bracket.
3500-Von Duprin Strike 299F
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
Von Duprin Part # 299F
299FPolished Stainless Steel Kick Plate | US32 Kick Plate | Polished Chrome
The Polished Stainless Steel Door Kick Plate is 16 gauge, or .050″ thick. Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. We often have people looking for Brushed Chrome or Polished Chrome, but the appearance of the two finishes next to each other is very difficult to tell which is which. Also a brushed chrome or polished chrome kick plate would be a brass plate which is then chrome plated and brushed or polished depending on the plate. Brass is a soft metal that dents easily, and also does not offer the corrosion resistance that stainless steel does. Since stainless steel is stable in any environment, they do not have to clear coat the plate.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.Custom sizes available starting around $0.37 per square inch depending quantity.
Please allow 1 week shipping time
GKP-pol-ss
