Search results for: 'dorma spring door chrome dorma many von'
-
Von Duprin 110388-00 6 Foot EL Cable Assembly
The Von Duprin 110388-00 6 Foot EL Cable Assembly connects directly into your power source and the Potted Circuit Breaker 050534. This 6 foot Cable Assembly is used on Von Duprin and Falcon Exit Devices that have the Electric Latch Retraction.
Von Duprin Part # 110388-00
G110388 -
Door Pull Handle 24
The Door Pull Handle 24 features a 6" center to center screw spacing. The handle is constructed of aluminum, stainless steel or brass depending on the desired finish. The handle is 1" solid diameter stock and the mounting posts are 3/4" diameter stock. It measures 8" overall length and projects from the door 2". It ships with thru bolts and finish washers. Also known as a Door Handle or Door Grip.
GHE24- -
Oil Rubbed Bronze Door Kick Plate
Our Dark Bronze Oil Rubbed Bronze Door Kick Plates (US10B) are a baked on powder coat on brass base metal. We switched to this finish 5 years ago due to color variations in the US10B Oil Rubbed Bronze finishes. The US version was much lighter than the Asian version, which is where most the door hardware is made these days. The cost of Oil Rubbing was going through the roof and many platers were having issue with the environmental impact and EPA regulations in the United States. Our Oil Rubbed Kick Plates are 16 gauge (.050″) thick.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut dark brown screw. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates, it is not recommended. Large plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. You can glue them on, I would recommend liquid nails, and some C Clamps with the door on saw horses.
Custom sizes available starting around $0.49 per square inch depending quantity
Please allow 2 week shipping time
GKP-DB -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
Wall Door Stop WS11
The WS11 door stop used to be under the Glynn-Johnson product line as the WB11 until they merged with H.B. Ives. At that point they became the WS11. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11x, except that it is designed for wood or drywall mounting and ships with wood screws and anchors.
GJWB11- -
Von Duprin Strike 264
The Von Duprin Strike 264 measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.
Von Duprin Part # 264
264 -
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Wall Door Stop / Bumper Heavy Duty Convex WS402CVX
The Ives WS402CVX Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ50C-Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50-Von Duprin 100316 5547 Top Plate
The Von Duprin 100316 is used on the 5547 on the top of the door. The top rod goes through the square hole on the plate. The plate shown in the Picture has both sides or LHR and RHR doors. One side of the strike is usually broken off depending on the hand of the door.
G100316Wall Mounted Door Stop WS33
The Ives Wall Mounted Door Stop WS33 is another hold back part from the Glynn-Johnson door stop era. I can not remember the Glynn-Johnson part #, but when Ives purchased them, they changed it to WS33. This stop is constructed of cast brass that is then plated to a brushed chrome finish. It features a replaceable rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft. And a sloping design that discourages vandalism.The base height is 3" with a width of 2-1/4", and a projection of 3-3/4", WS33 is furnished with wood screws for drywall mounting.
WS33Handicap Door Pull 119
With the Handicap Door Pull 119 you are able to get a closed fist behind the pull, which makes it a great ADA Door Pull. Also known as the Double Arm Pull it is constructed of aluminum, brass or stainless steel stock. It measures 8-1/2" overall length and has 5-1/4" centers on the mounting screws. The flat bar stock is 3/8" x 1", and the round mounting post is 3/4" diameter. Shipped with screws and finish washers. Also known as a Handicap Grip, ADA Door Pull or Handle.
GHP300-Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6Wall Mounted Automatic Door Holder 533
The 533 Automatic Wall Type Holder and Stop is a commercial grade door holder. The holder is mounted on the wall and strike is mounted on the door. It is constructed of cast brass, and measures 2 x 2-1/2 base and 2-1/8 inch high. Currently it is only available in brushed chrome.
GJ533Floor Door Stop Dome 1" Height FS436
Floor Dome Door Stop 1" Height FS436
We ship the H.B. Ives FS436 Floor Dome Stop, another product made by Ives that has been around for 50 plus years. Take a walk around a school made in the 1960's and you will probably find this door stop, or the hole were it used to be. This Dome Stop is used on doors without thresholds that have a bottom of the door to floor clearance of less than 5/8". The are constructed of cast aluminum or cast bronze depending on the finish you are looking for. The rubber stop is non-marring and replaceable. The stop has a base that is 1-3/4" x 2" oval, an overall height of 1" and a base height of 3/16".
GJFB13-Roller Bumper Offset RB470
The Ives Roller Bumper Offset RB470 are ideal if you have situations where doors meet each. They are constructed cast brass or bronze and are then plated to the desired finish. The arm projects 5" and the base has a 1-11/16" x 2-1/4". The device was just like the Glynn-Johnson RB3 or GJRB3.
GJRB3-Anodized Aluminum Door Kick Plate
Anodized Aluminum Door Kick Plates are the most cost effective, least expensive. The aluminum plates are 16 gauge, or .050″ thick and have a brushed or satin finish. They have an anodized finish to resist corrosion and we find these in many commercial buildings through out the United States.
Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″. You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.21 per square inch depending quantity
Please allow 1 week shipping time
GKP-alWall Door Stop / Bumper Heavy Duty Concave WS401CCV
The Ives WS401CCV Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ60C-Von Duprin 9927 Bottom Latch 050090
The Von Duprin 9927 Bottom Latch 050090 replaces and updates all 9827 and 9927 bottom latches to the new style, if your device was installed before October 1998. If your device is newer then October 1998, then use the G050401. Mounting screws and bracket are included.
Von Duprin Part # 050090
G99VR55Von Duprin Panic Device 7500 Mortise Body Only
This Von Duprin Panic Device 7500 Mortise Body Only is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.
Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.
We ship the 7500 in US32D, brushed stainless steel.
G7500
