Ives
-
Wall Door Stop / Holder WS20
The Ives Wall Door Stop / Holder WS20 is another door holder from Glynn-Johnson. The Chicago based manufacture made these for 40 plus years. When they were purchased from H.B Ives and merged into there line they became the WS20. This holder is constructed of cast brass and then plated to your desired finish. The hinged holding clip can be released by a gentle pushing on the door, which causes the clip to flip up and release the door. The piece ships with wood screws and anchors.
GJW20- -
Wall Door Stop / Holder WS445
The Ives Wall Door Stop / Holder WS445 has been a staple of the Ives product line for at least the last 45 years, and is the same product as the WS443 except it has a holder function. The stop features cast brass construction and then plated the the desired finish, which makes it ideal for interior or exterior use. The rubber tip is a non marring rubber, that can be replaced and we keep in stock. The stop has a 2-1/4" base diameter and a 3-11-16" projection from the wall. This product ships with an expansion shield and lead shield. This holder is considered a manually holder due to the fact you have to bend over and latch and unlatch it.
GJW27- -
Wall Door Stop / Holder WS40
The Ives Wall Door Stop / Holder WS40 is a door holder that has some history. We see this product in many schools, hospitals and churches that were built in the 50's, 60's and 70's. The WS40 was originally made and designed by Glynn-Johnson out of Chicago, Illinois, and was called the W40 or GJW40. H.B. Ives purchased Glynn-Johnson in 1990's and mergered this product into there offering, and changed the part # to WS40. The holder is made of cast brass or bronze and plated to your desired finish. The holding mechanism has a rubber bumper inside it to act as a door stop, and a brass spring loaded roller to act as a holder. The product ships with a universal screw package to mount on all types of walls. For the best results with this stop/holder the door and wall should be about 3-1/2" apart in the open position.
Base Height: 2"
Base Width: 2-1/2"
Base Projection: 2-1/4"
Engaged Projection: 3-1/2"
Strike Height: 2-1/16"
Strike Width: 3/4"
Strike Projection: 2"GJW40- -
Wall Door Stop WS11
The WS11 door stop used to be under the Glynn-Johnson product line as the WB11 until they merged with H.B. Ives. At that point they became the WS11. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11x, except that it is designed for wood or drywall mounting and ships with wood screws and anchors.
GJWB11- -
Wall Door Stop WS11X
The WS11X door stop used to be under the Glynn-Johnson product line as the WB11X until they merged with H.B. Ives. At that point they became the WS11X. This stop only is constructed of cast brass and then plated to your desired finish. The stop has a 2" diameter base and projects from the wall 3-3/4". This particular model is the same as the WS11, except that it is designed for a masonry type mounting and ships with an expansion sheild.
GJWB12- -
Ives Surface Bolt 8" SB453
The Ives Surface Bolt 8" SB453 has a 1-3/16" throw. The bar has a cross section measurement of 3/4" wide by 1/4" thick. It features a strong tension springs to prevent the bolt from creeping. The bolt is shipped with all of the fasteners and a universal top and a standard mortise strike. It is constructed of heavy duty steel that is then cadmium plated.
Ives part # SB453-8-TB-2C
GSB82C -
Wall Door Stop WS443
The Ives Wall Door Stop WS443 has been a staple of the Ives product line for at least the last 45 years. The stop features cast brass construction and then plated the the desired finish, which makes it ideal for interior or exterior use. The rubber tip is a non marring rubber, that can be replaced and we keep in stock. The stop has a 2-1/4" base diameter and a 3-11/16" projection from the wall. This product ships with an expansion shield and lead shield.
RB443HD- -
Floor Door Stop FS444
Floor Door Stop FS444
This door stop has been around a long time. We have been selling it for the past 35 years, and it is one of our best sellers year in and year out.
Features: Ideal for interior or exterior use. Cast brass construction. Accommodates door undercut up to 2-1/2". Non-marring rubber tip. Packed with expansion shield and lead shield. This Floor Mounted Door Stop is 3" high, and the base has a 2-1/2" diameter.
RB444HD- -
Wall Mounted Door Stop WS33
The Ives Wall Mounted Door Stop WS33 is another hold back part from the Glynn-Johnson door stop era. I can not remember the Glynn-Johnson part #, but when Ives purchased them, they changed it to WS33. This stop is constructed of cast brass that is then plated to the desired finish. It features a replaceable rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft. And a sloping design that discourages vandalism.The base height is 3" with a width of 2-1/4", and a projection of 3-3/4", WS33 is furnished with wood screws for drywall mounting
WS33- -
Wall Door Stop WS65
The Ives Wall Door Stop WS65 is one of the most economical door stops we sell that is still commercial quality. They are constructed of burnished cast aluminum. The WS65 has a base diameter of 1-5/8" and a 3-3/4" projection. The rubber tip is replaceable. This stop comes with the mounting screws.
WS65-- -
Lock Guard Narrow Line
• Narrow design unit for use on rose or escutcheon 3-1/2" or less.
• For use with Type 86 Mortise and Type 161 Cylinder Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the opening
between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel1-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2”1625NL- -
Lock Guard Standard Line
• Ideally suited for use with rose or escutcheon 2-3/4" wide or less.
• For use with Type 86 Mortise and Type 161 Cylindrical Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.2-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2"1625- -
Lock Guard Slim Line
• Designed for use on all Type 161 Cylindrical Locks (ANSI 156.2 Series 2000)
Monolock and Unilock.
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.1-1/2" Wide x 7" High
Stud center to center: 4-1/2"1625SL- -
Floor Door Stop-Security FS18
Floor Door Stop-Security FS18 is designed for areas of high vandalism. The molded rubber is flame resistant and mounted to a 5/8" threaded mounting shaft. Once the 7/8" diameter hole is drilled to a depth of 2-1/2" it can be grouted in concrete and leaves no exposed fasteners. The recommended grout is Thorogrip. They are ideal for jail or security cell areas. There are two versions of this door stop one projects 1-1/2" (FS18S) out of the floor and the other 3" (FS18L).
GFS18- -
Floor Door Stop / Holder
The F20 or GJF20 was a mainstay of Glynn-Johnson for years. When the Glynn-Johnson door stop line merged with H.B. Ives it became the FS20. This door stop has been discontinued from Ives, but we have been able find a large stock. This Floor Mounted Door Stop also holds the door open, when in the latched position you can push the door and the holding latch will flip up and unlock thee holding clip. It is constructed of cast bronze or brass and then plated to your desired finish. This stop has a 2-1/2" long base that is 1-1/2" wide. The overall height is 3-1/8" with a 2-5/16" floor to rubber stop centerline. For use with door undercut up to 2-1/2".
GJF20- -
Ives FB458 Metal Door Flush Bolt
Ives FB458 Metal Door Flush Bolt
The Ives FB458 is a UL Listed Flush Bolt for use on Fire Doors. The face plate measures 1" wide by 6-3/4" long with a depth of 1-1/8". Hole spacing is 1/2 inch by 6-1/4 inches on centers. The bolt has a 3/4" throw and is 1/2" diameter. This Flush Bolt is available in Polished Brass, Oil Rubbed Bronze (dark brown) and Brushed Chrome. We try to stock the 12" rods, which are standard, but we can also get 18", 24", 36" and 48"
Ives Part # FB458
FB458- -
Ives FB40 Automatic Flush Bolt
Wood Door Automatic Flush Bolt FB40
H.B. Ives FB40 Series are sold has Top, Bottom or in Pairs (top and bottom). Fully automatic, inactive door is latched when active door closes, bolts retract when active door is opened. Top Bolt has no spring tension. They are non handed, but the top and bottom bolts are different. The body size is 1" wide, 8-1/2" tall and 2" deep, the bolts have a 3/4" throw with a 7/8" vertical adjustment.
Ives Part #'s
FB41P - Pairs
FB41T - Top
FB41B - BottomFB40 -
Ives RL30 Roller Latch
Ives RL30 Roller Latch
The Ives Roller Latch RL30 is constructed of Forged Brass and Plated to your finish. Furnished with a Nylon Roller. Body measures 1" wide by 3-3/8" high by 1-11/16" deep. The roller has a maximum projection of 3/8" and is easily adjustable.
RL30- -
Ives RL32 Roller Latch
Ives RL32 Roller Latch
The Ives RL32 Roller Latch is constructed of Brass and Plated to your desired finish. The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep. The roller is constructed of Nylon, and has an adjustable projection up to 1/2". Fits a standard heavy-duty cylindrical lock cutout.
RL32- -
Ives RLPART.1025 Roller and Rivet for RL30/RL1152
Ives RLPART.1025 Roller and Rivet for RL30/RL1152
This replacement Nylon Roller and Rivet Package is for the Ives RL30 and RL1152 Roller Latches. The Roller measures 3/4" high by 5/8" diameter. The Rivet measures 1-1/16" long and is threaded on one side.
Ives Part # RLPART.1025
RL30NR -
Ives LG1 Lock Guard
The Lock Guard with Security Pin is ideal to cover the latchbolt area of the door, lock and frame, with the added protection of a security pin to prevent separation of the door and door frame. The plate is through bolted with carriage bolts and nuts, which are included with the guard. The plate is constructed of 13 gauge stainless steel. The plate measures 3" wide and 11-1/2" high, with a center to center on the mounting bolts of 10-1/2".
Ives Part Number LG1-US32D
LG1- -
Floor Mounted Dome Stop FS439
The Ives Universal Dome Floor Stop FS439 is constructed of cast zinc or stainless steel, depending on the finish. The stop measures 1-1/2" high, with a base height of 1/4" and base diameter of 1-7/8". The pad has a height of 1-1/8" from the floor.
Ives Part Number FS439
GFS439- -
Kickdown Door Holder Rubber Shoe For GJ1154M and GJL444-555
Rubber Shoe For GJ1154M and GJL444-555 Kickdown Door Stop / Holder
Replacement rubber shoe
5/8" insert diameter
1" base diameter
8-32 threaded screwGJ1154