Von Duprin Exit Devices
-
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
Von Duprin 8827 Chassis Tie Rod Pkg 050328
Von Duprin 8827 Chassis Tie Rod Pkg 050328
The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.
Von Duprin Part # 050328
Old Von Duprin Part # 96761688VR195 -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040 -
Von Duprin 55 Hinge Case Spring 090052
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
Von Duprin part # 090052
55R200 -
Von Duprin Dogging Hook 090044
The Von Duprin Dogging Hook 090044 is the piece that grabs the push bar mechanism and keeps it in the dogged position. The does wear out, but it takes a long time. This piece is used on the 22, 33A, 35A, 98 and 99 series devices made after 1997. We sell this part individually and it is #5 on the diagram.
G090044 -
Von Duprin 55 Dog Screw-090053
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
Von Duprin part # 090053
55R85 -
Von Duprin 992/994 Lift Spring 971573
Von Duprin 992/994 Lever Lift Spring 971573
The spring measures 1-5/8" long with a 7/16" diameter. We find two of these springs per 992 and 994 series lever trims. These springs help support the lever handle and return it to the proper position.
Von Duprin Part # 971573-00
G971573 -
Von Duprin 88 Tube Attaching Ring 090021
The Von Duprin 88 Tube Attaching Ring 090021 is also used on the Von Duprin 55. The ring fits over the device lever arm, and is expanded by the Wedge (88R90) and the Wedge Tite Screw (88R100). When the Wedge Tite Screw is tightened the Ring expands and keeps the crossbar parallel to the door. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110 -
Von Duprin 88 and 55 Wedge Tite Screw 090081
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
Von Duprin Part # 090081
88R100 -
Von Duprin NL Drive Screw 090074
Von Duprin NL Drive Screw 090074
The 090074 NL Drive Screw is used on the Von Duprin 22, 98 and 99 Exit Devices to control the rotation of the key cylinder cam. This small set screw, screws into the back of the chassis assembly next to the receptor for the Rim Key Cylinder. The set screw measures 5/16" long by 3/16" diameter. Note: When the NL drive screw is left in back of device, the outside cylinder will function only as a Night Latch. The Night Latch function means the door can only be opened, but not dogged open with the key cylinder.
Von Duprin Part # 090074
Old Von Duprin Part # 970441G090074 -
Panic Hex Key 5/32" x 3-1/16" Long
The Panic Hex Key 5/32" x 3-1/16" Long is a must for Von Duprin 22, 33, 35, 98 and 99 panic hardware. This key has a longer shaft to reach deeper into the Von Duprin Panic Devices. This key is also known as Hex Key, Dog Key, Allen Key, and Dogging Key.
88R60 -
Von Duprin 22 Metal End Cap 900397
The Von Duprin 22 Mechanism Metal End Cap 900397 is new for 2016. This new kit replaces the 900397 with a metal end cap, which is has always been a weak link of the 22 series. The package includes the End Cap, Bracket and the Mounting Screws. This cap and bracket will work on all of the 22 and 2227 series.
Von Duprin part # 900397
G22R10M- -
Von Duprin 55 End Case Kit 050196 and 050197
The Von Duprin 55 End Case is the housing on the hinge side of the door. The function of this housing is to lift the cross bar, and support the function of the Active Case. If your housing is on the right side when standing inside looking out, then you would order the Right Hand Case. The package includes the housing, springs and back plate, the arm is not included. The current part number on this part is 050196 and 050197, the old part number is 111931 and 111932.
Other finishes are available upon request.
55R30 -
Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6