Search results for: 'mounting holder 8 1 2 center to cap'
-
Von Duprin 050537 HD-EL Solenoid Plunger
Von Duprin 050537 HD-EL Solenoid Plunger
#5 On Diagram under "More Views". Measures 3" long x 7/8" diameter.
Works On The Von Duprin 33A/35A And 98/99 Exit Devices
No longer Available
G050537 -
Von Duprin 8827 Bottom Latch Case 050461
The Von Duprin 8827 Bottom Latch Case 050461 is used on all Von Duprin 8827 non fire rated exits. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. Included mounting screws.
Von Duprin Part # 050461
Old part # 10175188VR170 -
Von Duprin 154 Mullion Stabilizer Package
The Von Duprin Mullion Stabilizer Package are used with Von Duprin Mullions to stop any deflection on the mullion, which may cause the exit devices to release. We run into issues where people are able to shake the door, and the door opens. The package includes two sets of stabilizers and all the mounting screws.
G154- -
Von Duprin 2227/3327A/9927 Top Latch 050400
The Von Duprin 050400 Top Latch is used on the 2227, 3327A, 3427A, 9827 and 9927 exit devices. It is used the Fire-Rated along with the standard Panic Devices. The 050400 is sold without the the Mounting Bracket, if you need the Mounting Bracket you can order the 050546, or order the G99VR10 (050091) which will come with the Bracket. This latch is for use on devices shipped after October 1998. This is usually the problem if your bottom rod is dragging on the floor. Includes screws.
Von Duprin Part # 050400
G050400 -
Von Duprin 9927 Bottom Latch 050090
The Von Duprin 9927 Bottom Latch 050090 replaces and updates all 9827 and 9927 bottom latches to the new style, if your device was installed before October 1998. If your device is newer then October 1998, then use the G050401. Mounting screws and bracket are included.
Von Duprin Part # 050090
G99VR55 -
Von Duprin Panic Device 990NL Trim
The Von Duprin Panic Device 990NL Trim is known as a Night Latch Trim. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. The key locks and unlocks the interior exit device. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990NL-R&V. The key cylinder is sold separately.
99NL -
Von Duprin 990DT Trim
The Von Duprin 990DT Trim is known as a Dummy Trim. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990DT-R&V.
99DT- -
Von Duprin Panic Device 990TP Trim
The Von Duprin 990TP Trim is known as a Thump Piece Trim. The key cylinder locks and unlocks the thumb piece, key cylinder sold separately. This plate mounts on the exterior of the door, and the welded on mounting studs line up with the 99 device on the interior of the building. If you have a different manufacture or a different Von Duprin series on the interior, it will not line up. On the back of this plate we usually find the number 990 stamped on it. The plate shown here is for the Rim and Surface Vertical Rod 99 and 98 devices. If you have a Mortise or Concealed Vertical Rod, call us and we will order that model. The plate measures 3" wide by 14-3/16" tall. Order here for the 990TP-R&V.
99TP -
Von Duprin 88 Panic Device
The Von Duprin 88 Panic Device has been around since the 1950's, and is probably the device that put Von Duprin on the Map. It is designed for all types of single and double doors with mullions. It is field reversible, and ships with a 42" cross bar that can be cut down in the field. The device is dogged down with a 5/32" hex key, and ships with all mounting screws and the 299 strike.
88EO- -
Von Duprin Panic Hardware 210K Knob Trim
The Von Duprin Panic Device 210K Knob Trim is for use on the 22 Rim and 2227 Surface Vertical Rod devices. Key in knob can lock and unlock the knob. Since the enforcement of local ADA standards, this knob is probably at the end of this life, no one seems to want these anymore. The mounting plate measures 3" wide by 4-25/32", and is 3-32" thick. We do have parts on this Knob, but at this point they are not on the website.
220K- -
Von Duprin Panic Device 230L Lever Trim
The Von Duprin Panic Device 230L Lever Trim will work on the 22 and 2227 series exit devices. In 2008 this lever was redesigned and went from a key in the lever to the new style which has the key above the lever. The plate measures 3" wide by 6-3/8" high and is 15/16" thick. This lever only comes in sprayed aluminum or dark bronze. We also have replacement parts for this particular trim piece in stock, email us under the contact tab at the top of the page.
Cylinder not included
22L -
Von Duprin 8827 Bottom Vertical Rod Assembly 050455
Von Duprin 8827 Bottom Vertical Rod Assembly
This bottom vertical rod is used on non fire rated doors. The rod includes the bottom rod connector. The rod is 31-7/8 inches long, excluding the rod connector.
Von Duprin Part #050455
Old Part #101777 and 10323488VR150- -
Von Duprin 88 and 55 Wedge Tite Screw 090081
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
Von Duprin Part # 090081
88R100 -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
Von Duprin Panic Device Keyed Mullion Retrofit Kit KR54
The Von Duprin Panic Device Keyed Mullion Retrofit Kit KR54 is used to convert the 1654 and 4954. Keyed Removable Steel Mullions makes removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when re-installed, without use of the cylinder key. Uses a 1-1/4´´mortise cylinder with a straight cam (Schlage cam reference B502-191). Cylinders are sold separately.
Von Duprin Part # 050168
KR54 -
Von Duprin 88 and 55 Cross Bar 967738
The Von Duprin 88 and 55 Cross Bar 967738 has been in use since the 1950's. The bar is 1" in diameter and is 42" long and can be cut down in the field. One side of the bar will be cut for the wedge tite screw opening.
Von Duprin Part # 050004
Old Part # 96773888R120- -
Von Duprin 99 Push Bar Retrofit Kit-Pbkit
The Von Duprin 99 Push Bar Retrofit Kit-Pbkit updates your current version touch pad, to the newest version. Used on all the Von Duprin 33A, 35A, 99 and 98's. For doors 30" to 36" order the 36" size. If your door is 36" to 48" order the 48" size. The Push Bar is 18" wide on the 36" version. Please allow 1 week for delivery.
Von Duprin part # PBKIT
G99R35 -
Von Duprin 22, 33, And 99 Dogging Shaft 090040
The Von Duprin 22, 33, And 99 Dogging Shaft 090040 is the peice that the hex dogging key would fit into. The shaft is for a 5/32" dog key, but it has to be the long version. The shorter versions will not have enough reach to get all the way into the shaft. This is a very common problem area, the hole that the key fits in is only about 1/4" deep, and if you do not push down on the hex key when locking it open it will round out over time. To remove the shaft, just pull it straight out with a part of channel locks. We reinstalling the new one you might have to bend the ends of the adapter spring 090042 back down. This dogging shaft is for use on all Von Duprin Panic Exit Devices shipped after 1997.
G090040