The Von Duprin 9927 Center Case 050021 center case replaces all earlier versions of the 9827 and 9927 Center Cases. Everything shown in the picture is included with the product. Along with all the mounting screws.
The Von Duprin 88 Wedge Ring 090020 is also used on the Von Duprin 55's. The Wedge Tite Screw applies pressure on the Wedge which expands the Tube Attaching Ring to grip the Cross Bar. Measures 5/8" on the flat edge.
The Von Duprin 050580 Weather Stripping is for there 5654 and 5754 Mullions. Each strip is 10' long and two would be required per mullion. This product is specific to Von Duprin products and will usually only work on Von Duprin Products.
The Von Duprin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.
The Von Duprin 900850 Latch Cover Screw Package is used on the 22, 33, 35, 98 and 99 Series surface vertical rod latch covers. The are sold in packages of 2 screws.
The Von Duprin 8827 050466 Top Latch And Cover is the 050460 (latch) and 050464 (cover) in one convenient package. The package includes the cover screws and mount screws.
The Von Duprin 900620 35/3348 98/9947 Adjusting Screw Package is used to adjust the concealed vertical rods. This package is used on the 3347, 3547, 3347-F, 3547-F, 9847, 9847-F, 9947 and 9947-F. This is a package of 2.
The Von Duprin 338 Strike measures 1-5/8" by 1-7/8" with a 5/8" projection. The screw mounting is 1-7/8". This strike is used as a bottom strike on the Von Duprin surface and standard equipment there concealed vertical rod devices 3347, 3547, 5547 8847, 9847 and 9947.
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
The Von Duprin 090039 is used in the push bar assembly to return the latch. It is known as the Base Plate Latch Return Spring or Latch Return Spring. It is used on the 22, 33A, 35A, 98 and 99 Devices. The spring is 2-1/4 inch long with a 3/8 inch diameter.
The Von Duprin 2227 Rod Guides Assembly 112063 works on all of the Von Duprin 2227's, and replaces the older style that featured the plastic cap and the springs. This device is used to add strength and rigidity to the top and bottom rods on there surface vertical rod.
The Von Duprin Dogging Adapter Spring 090042 is the clip that holds the dogging shaft in the assembly. We sell these individually, and it is the #2 item on the diagram.
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
The Von Duprin 050390 Bottom Mullion Fitting is the Bottom Fitting for the 1654, 4754, 4854, and 4954 Von Duprin Mullions. The 050390 measures 5/8" thick by 2" wide and 3" long excluding the flange the projects out the one end. We find the number 961040-70 ESE cast right in the fitting. The mounting holes are 2-1/4" on center. Mounting Screws included.
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
The Von Duprin 090076 Spring is located in top latch of the Surface Vertical Rod. It is used on the 2227, 3327A, 3427A, 9827 and 9927 models. It is number 18 in the attached diagram. They are sold in packages of 10.
The Von Duprin Panic Device 880TP Trim is for the 88 series only. The stanchions welded on the back line up with the 88 device on the interior. The optional key cylinder locks and unlocks the thumb piece. The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.
The Von Duprin Panic Device 210DT Trim is part of there economy series trims. This trim is just a pull, but will line up with the chassis mounting holes of the 22 and 2227 devices. The plate measures 5-3/8" x 4-25/32" x 3/32", with a projection of 1-31/32".
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
The Von Duprin 22 Mechanism Metal End Cap 900397 is new for 2016. This new kit replaces the 900397 with a metal end cap, which is has always been a weak link of the 22 series. The package includes the End Cap, Bracket and the Mounting Screws. This cap and bracket will work on all of the 22 and 2227 series.
G22VR80-
