The Von Duprin Latch Mounting Bracket 050546 is used on the 2227, 3327 and 9927. It is for use with the 050400, 050401, 050091 and 050090 Surface Vertical Latches.
Von Duprin Part # 050546 Old Von Duprin Part # 971567
The Von Duprin Dogging Spring 090041 is the spring that activates the Dogging Hook # 090044. These do occasionally fail, we sell them individually. It is # 3 on the diagram.
The Von Duprin 9927 Center Case 050021 center case replaces all earlier versions of the 9827 and 9927 Center Cases. Everything shown in the picture is included with the product. Along with all the mounting screws.
The Von Duprin 050580 Weather Stripping is for there 5654 and 5754 Mullions. Each strip is 10' long and two would be required per mullion. This product is specific to Von Duprin products and will usually only work on Von Duprin Products.
The Von Duprin 900894 230L Tailpiece Auxiliary includes the Tailpiece (steel), Tailpiece Guide (nylon), and the Pine Tree Clip (nylon). The Tailpiece measures about 2-1/2" x 1/4" x 3/32" thick.
The Von Duprin 2227 Center Case Cover 968888 comes in an Aluminum SP-28 or Dark Brown SP-313 color. This piece is for used on the 2227 Surface Vertical Rod Panic Hardware. Package also included mounting screws.
The Von Duprin 900620 35/3348 98/9947 Adjusting Screw Package is used to adjust the concealed vertical rods. This package is used on the 3347, 3547, 3347-F, 3547-F, 9847, 9847-F, 9947 and 9947-F. This is a package of 2.
The Von Duprin Dogging Adapter 090043 is the piece that the 090042 and 090040 fit through and lock in place. These piece very rarely has to be replaced. The Shaft 090040 is usually the part you need to replace. We sell these individually.
The Von Duprin 2227 Bottom Vertical Rod 109362 has a length of 33-1/4" to 33-1/2" that is set at the factory. All the bottom rods are the same length because of ADA standards. The top rods are field adjustable.
The Von Duprin 88 Wedge Ring 090020 is also used on the Von Duprin 55's. The Wedge Tite Screw applies pressure on the Wedge which expands the Tube Attaching Ring to grip the Cross Bar. Measures 5/8" on the flat edge.
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
The Von Duprin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.
The Von Duprin 900850 Latch Cover Screw Package is used on the 22, 33, 35, 98 and 99 Series surface vertical rod latch covers. The are sold in packages of 2 screws.
The Von Duprin 9927 Rod Guide Assembly 112063 works on all of the Von Duprin 98 and 9927's. The guide keeps the rods from bowing or getting bent by hand carts, or rowdy patrons. Replaces the old style which had the cover and springs.
The Von Duprin Dogging Adapter Spring 090042 is the clip that holds the dogging shaft in the assembly. We sell these individually, and it is the #2 item on the diagram.
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
This Von Duprin 386DT Dummy Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Duprin 33A on the inside so they are on cohesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386DT Dummy Trim is non handed.
The Von Duprin 22 Mechanism Metal End Cap 900397 is new for 2016. This new kit replaces the 900397 with a metal end cap, which is has always been a weak link of the 22 series. The package includes the End Cap, Bracket and the Mounting Screws. This cap and bracket will work on all of the 22 and 2227 series.
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G99VR35-
