Search results for: 'dogging device for panic door'
-
Jackson 1095P Paddle Panic Hardware
The Jackson 1095P Paddle Panic Hardware is an alternative to the cross bar or push pad style panic hardware. The device is the same as the Jackson 1095, but with a paddle instead of the cross bar. This device is for use on aluminum or steel doors only. The device is mounted on surface studs that are tapped into the door. On a wood door they will pull out.
Right Hand Reverse Shown

1095P- -
Sargent 8700 Panic Device
For Doors Wood or metal. 1-3/4" (44 mm) thick standard.
minimum stile with trim and 3-1/2"
Mounting Supplied standard with wood and machine screws
Chassis Cover Cold drawn brass, bronze or stainless steel
Chassis Nonferrous alloy
Hand Handed. Specify RHRB or LHRB
Dogging Feature Allen-type dogging furnished standard.
Top and Bottom Bolts Brass, stainless steel
8700EO -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Sargent 20/30/60/80 Dogging Kit 68-2596
The Sargent 20/30/60/80 Dogging Kit 68-2596 is used on the Sargent 20, Sargent 30, Sargent 60, and Sargent 80 Series Panic Hardware. This dogging assembly kit has been around since the 1980's. We only sell the dogging assembly parts as a complete set.
Sargent part # 68-2596
G80200 -
Monarch 19 Series Hex Dogging Kit
Falcon/Monarch 19 Series Hex Dogging Assembly and Cover have been changed. As of April 12, 2022 the kit now includes a new style dogging assembly also.
We know this kit will work on the 19/24/25 Series, and are not sure if it will work on the Monarch 17/18 Series Dogging Cover goes over the dogging mechanism on the hinge side of the exit device. Sometimes when the end cap goes missing, this cover plate also disappears.
Monarch old part #s 195 and 194
Monarch/Falcon new part #'s 650297 and 650303Size is the width of the Device, a 36 inch device is usally only 32 inches wide, a 48 inch device is usually about 42 inches wide.
G19R80- -
Yale 1500 60-1500-1184 Dogging Shaft
Yale 1500 60-1500-1184 Dogging Shaft
Used on the Yale 1500 Rim and Surface Vertical Rod Devices. This is the peice that the Dogging Key goes in to actuate the Dogging Piece. The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter. The hex is 5/32"
Yale Part # 60-1500-1184
G6015001184 -
Adams Rite Cylinder Dogging Assembly 31-0265-01-IP
The Adams Rite 31-0265-01-IP is used on the current versions of their devices for Cylinder Dogging. Cylinder Dogging is when you have a Mortise Cylinder to lock the device in the unlocked positions (Dogged). Very similar to the Hex Key Dogging Assembly, but the mounting plate is longer.
G31026501IP -
Von Duprin Panic Device 7500 Mortise Body Only
This Von Duprin Panic Device 7500 Mortise Body Only is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.
Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.
We ship the 7500 in US32D, brushed stainless steel.
G7500 -
Jackson Panic Device 1095 Standard Strike
The Jackson Panic Device 1095 Standard Strike is a strike they have been using for the past 20 years. You might have one of the older roller strikes, but this will work in its place. The older style roller strike is no longer available. Jackson Exit Device part # 30-2436.
G109556 -
Adams Rite 8800 Panic Device
Adams Rite 8800 Panic Device
The 8800 features the Starwheel locking bolt that interlocks door to the door frame. The 36" version is in stock, we can also get the 30", 42" and 48" devices, lead time is 2-3 weeks. This device is used exclusively on aluminum framed glass storefront doors. Replacement parts are available.
8800EO- -
Panic Hex Key 5/32" x 3-1/16" Long
The Panic Hex Key 5/32" x 3-1/16" Long is a must for Von Duprin 22, 33, 35, 98 and 99 panic hardware. This key has a longer shaft to reach deeper into the Von Duprin Panic Devices. This key is also known as Hex Key, Dog Key, Allen Key, and Dogging Key.
88R60 -
Von Duprin 9927 Panic Device
Von Duprin 9827/9927 surface mounted vertical rod device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The Von Duprin 9827 device has a smooth mechanism case and the Von Duprin 9927 device has a grooved case. The surface vertical rod device is non-handed.
9927EO- -
Cal Royal Panic Device 2000 Series Lever Trim
Cal Royal 2000 Series Exit Device Lever Trim
Non-handed Grade 1 (Clutch Style)
Cylindrical body hardened steel heavy duty tailpiece. For
1¾” and 2 ¼” doors. Prefix THI before part # for 2 ¼” door
thickness. Available for fire and non fire rated rim and
vertical rod exit devices.
Rose diameter 3 ½”, lever length 4 ¾”.ENTOOL- -
Von Duprin 55 Dog Screw-090053
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
Von Duprin part # 090053
55R85 -
Jackson Panic Device Top Bolt Guide Assembly 1085/1285/2086
The Jackson Panic Device Top Bolt Guide Assembly is used on the 1085, 1285, and 2086 hardware. The piece works by sliding over the top rod when the device is opened. This keeps the rods retracted until the Plunger hits the Trip Assembly when it is closing. Upon hitting the Trip Assy, the plate slides over and the rods retract. It measures 1-1/2” deep x 1-1/16” wide x 15/16” tall, with a hole spacing of 3/4" on the mounting screws. Assembly includes the mounting screws. The Jackson Part number is 30-934.
G108518 -
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Cover Plate 968595 968596
Von Duprin 22 Dogging Cover Plate. Plate covers the dogging assy, or hinge side of the exit device. This plate sides off when the plastic end cap breaks or goes missing.
Von Duprin Part # 968595 measures 10-3/4" Long for 3' devices
Von Duprin Part # 968596 measures 16-3/4" Long for 4' devicesG22R90- -
Panic Hex Key 5/32" X 2-1/8" Long
The Panic Hex Key 5/32" X 2-1/8" Long is usually used on Dor-O-Matic, Falcon, Corbin Russwin, Von Duprin 55 and 88 and Yale panic hardware. This Hex Dog Key is not long enough for the Von Duprin 33, 34, 33A, 35B, 98 or 99 Exit Devices. Also known as Hex Key, Dog Key, Allen Key, Dogging Key
88R60-SHORT -
Von Duprin 050709 Old Style Dogging Assembly
The Von Duprin 050709 Dogging Assembly is used to update the Von Duprin 22, 33, 35, 98 and 99 device shipped before 1997. The dogging key on this assembly is 5/32", and you would want to use the longer version of our 88R60 dog key.
Von Duprin Part # 050709
Old Part # 050153G050709 -
Jackson Panic Device 1295 Push Pad End Cap Package
Jackson Panic Device 1295 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2677
New Jackson Part # 30-2654G302677- -
Jackson 1085 Panic Device Concealed Vertical Rod
The Jackson 1085 Panic Device is one of a few original manufactures of Panic Hardware for aluminum framed glass doors, or storefront doors. The 1085, 1095 along with their door closer the 20-330 were installed on about half of these doors in the 1970's and 1980's. They were installed on Vistawall and Kawneer doors just to name a few. Universally recognized as the standard for aluminum storefront hardware it is made of high tensile strength aluminum. The device is Non Handed, Comes with 45" cross bar that is easily cut in the field. Also includes the Concealed Vertical Rods, Screws and Strikes.
Replacement parts are available, in stock!
1085EO






































