Search results for: 'arm-a-door panic bar'
-
Door Push Plate 62
The Door Push Plate 62 is constructed of 16 guage (.050") thick aluminum, stainless steel, brass or bronze depending on your finish. They measure 7-1/2" by 15" tall. This plate is handed left and right, the one shown on the website is a Left Hand. Plate comes with matching finish mounting screws.
GPH62- -
Door Silencer For Metal Frames
For use on metal frames featuring
pneumatic design that, once installed,
forms an air pocket to absorb sound and
reduce noise of door closing.Diameter: 1/2"
Thickness: 1/8"
GJ64 -
Falcon Automatic Opener 8242
The Falcon Automatic Opener 8242 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8242 is a non handed, surface mounted, 115 volt closer for a push side mounting. If your door is an inswinging door you would use the 8231. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8242- -
Falcon Automatic Opener 8231
The Falcon Automatic Opener 8231 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8231 is a non handed, surface mounted, 115 volt closer for a pull side mounting. If your door is an outswinging door you would use the 8242. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8231- -
Door Edging 305
Fabricated from B & S 16 ga. (.050). Standard lengths are 36", 42" and 48". Custom capabilities include variations of all of the above parts including frame protectors and vertical rod protectors.
Custom sizes are available!
Screws included for mounting
Please allow 7-10 for shipment.
GDE305 -
Continuous Full Surface Geared Hinge
The Ives 157XY Continuous Full Surface Geared Hinge is an ideal solution for the replacement or worn or broken storefront door pivots, which we run across quite often. I our opinion this is the best solution if you can not find a compatable replacement pivot. The geared hinge will not allow the door to twist, which makes your door more sturdy in the frame. This hinge measures 83" long and is 3-7/16" wide included the cover which hides the screw mounting. A patented easy to install, heavy duty hinge which offers lateral and vertical adjustablility whle the door is still hanging. The hinge is non handed, will mount on a narrow frame, can be cut down in the field and will work on doors up to 550 pounds. 12-24 x 1/2" steel self drilling and tapping screws are included.GFS102- -
Back to Back Mounted Handles 3/4 Inch Diameter
Back to Back mounted handles constructed of 3/4 inch round stock. One handle will be threaded and the other will have a stud mounting that is secured by a set screw. The connecting stud is for 1-3/4 inch thick doors, if you door is a different thickness let us know in the Comments Section of the Check out process, or email us.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GHE25x25 -
Reinforcing Pivot Hinge
The reinforcing pivot hinge is a good way to solve door sag issues. And also be a preventative solutions for future isses with extra heavy or wide doors. The hinges comes in two sizes 4 or 4.5 inches, and two finishes, prime coat and satin chrome. The hinge uses a heavy duty ball-bearing to add extra life. The base metal is steel.
GBB85 -
Cal-Royal 45 Narrow Stile Rim Device
The Cal-Royal 45 Narrow Stile Rim Device is part of the new 4500 Series. They are designed for Narrow Stile doors with a minimum of an 1-3/4" stile width. This is a Grade 1 Exit Device, which is the highest traffic rating possible. Exit device ships with strike and mounting screws.
Shown is Left Hand Reverse
Opposite would be Right Hand Reverse45-RIM -
Von Duprin 050534 EL Potted Circuit Breaker
The Von Duprin 050534 EL Potted Circuit Breaker measures 5" long by 1-1/4" wide and 7/16" thick including the wires. This piece spikes the current to the solenoid to open the door, then lowers the current to keep the device open. The 050534 has a plug for the two wire input, and a plug for the 3 wire output. This Potted Circuit Breaker is also used on the Doromatic/Falcon Exit Devices, EL1490, EL1590, EL1690, EL1790, and EL2390. We sometimes find the number 101031-00 and 2148 on a sticker.
Old Von Duprin Part # 110741
Von Duprin Part # 050534
Doromatic/Falcon Part # 050534-00G050534 -
Anodized Aluminum Door Kick Plate
Anodized Aluminum Door Kick Plates are the most cost effective, least expensive. The aluminum plates are 16 gauge, or .050″ thick and have a brushed or satin finish. They have an anodized finish to resist corrosion and we find these in many commercial buildings through out the United States.
Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″. You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.21 per square inch depending quantity
Please allow 1 week shipping time
GKP-al -
Zipper Pile Weatherstrip .187" Backing - .450" Pile Height - 100' Roll
Zipper Pile Weatherstrip is a full density, high performance, water-resistant pile woven to a unique zipper tooth design polypropylene backing. The zipper tooth design allows the pile to easily snap into the extrusion slot from above rather than having to slide the pile in from the ends. Whether it's being used in manufacturing or retrofitted, the application is much easier and faster. It even works if the slot is slightly off size. Zipper Pile can be used to retrofit aluminum, vinyl, fiberglass or wood T-slots without the need to take the complete window or door sash apart. The double center fin provides a true weather seal, compared to other piles without a fin suited for vibration reduction and pest control only.
Z78251C -
Full Mortise Regular Weight Hinge
The Full Mortise Regular Weight Hinge are for lighter weight interior doors without a door closer. They are constructed of 10 gauge (.134”) steel that is then plated or paint primed. We sell them in boxes of 3 hinges, and they ship with machine and wood screws.
Shown in brushed brass
G100XX -
Cal-Royal 9800 Rim Device
The Cal-Royal 9800 Rim Device is a grade 1 Heavy Duty Exit Device. The 9800 has the same template as the 8800 and 9800 with escutcheon lever trim. The 36 inch device will be 32 inches wide and can be cut down an additional 2" to fit doors as narrow as 30 inches. The 48 inch will be 44 inches wide and can be cut down to fit doors 36 inches wide. The device is non handed, meaning it will work on a left hand reverse or right hand reverse door. Strike and mounting screws are included.
9800EO- -
Falcon / Dor-o-Matic 2390 Exit Device
Effective December 20, 2024 the 2390 has been discontinued. Falcon Doromatic is working on retro-fit plates to work with the 1690.
Doromatic 2390 Exit Device
The 2390 is a Grade 1 exit device designed for high use and abuse, and delivers a variety of performance features that ensure smooth, easy and reliable operation. Easier rod adjustment simplifies installation. This device is for replacment of older worn out Falcon / Dor-o-Matic 2390's. This is not a good exit device to use to replace devices from different manufactures.To order specify:Door Width:42" (Device size has a 21" Touchbar)
48" (Device size has a 24" Touchbar)Color:
Aluminum
Dark Bronze
Device Centerline to Finished Floor Measurement in inches:2390EO- -
Glynn-Johnson Overhead Door Holder 450 Series Surface Mounted
The Glynn-Johnson Overhead Door Holder 450 Series provide reliable and versatile surface-mounted overhead door control for all medium to light-duty applications. The visible components are available in a wide variety of architectural finishes to complement any design. The Glynn-Johnson 450 series holders and stops are designed for installation in virtually all types of doors and frames including doors with conventional butt hinges, offset pivots, continuous hinges, swing clear hinges and many other specialty hinges. The templates provided allow for variable mounting positions, ranging from 85° - 110° of opening.
The 450 Series replaces the older GJ360, GJ370 and GJ380 Series.
GJ450 -
Von Duprin 99 Cover Plate 050114
The Von Duprin 99 Cover Plate 050114 is for use on the 33A, 35A, 98 and 99 devices. Covers the dogging assembly on the hinge side of the door. The usually fall off when the End Cap is not on the exit device. Von Duprin is only shipping a 20-1/2" cover plate now, which will work on 3' and 4' doors, you will have to cut more off if you have a 3' device with a hack saw or chop saw.
Von Duprin Part # 050114 and 050117 Hex Key Dog Conversion Kit
Von Duprin 99 Cover Plate 050114
G99R50 -
Polished Stainless Steel Kick Plate | US32 Kick Plate | Polished Chrome
The Polished Stainless Steel Door Kick Plate is 16 gauge, or .050″ thick. Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. We often have people looking for Brushed Chrome or Polished Chrome, but the appearance of the two finishes next to each other is very difficult to tell which is which. Also a brushed chrome or polished chrome kick plate would be a brass plate which is then chrome plated and brushed or polished depending on the plate. Brass is a soft metal that dents easily, and also does not offer the corrosion resistance that stainless steel does. Since stainless steel is stable in any environment, they do not have to clear coat the plate.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.Custom sizes available starting around $0.37 per square inch depending quantity.
Please allow 1 week shipping time
GKP-pol-ss -
SEM7820-516 LCN Magnet Core Assembly
The SEM7830-516 LCN Magnet Core Assembly is just the Tri Voltage Magnet Core. This core is used on the Floor Mounted SEM7830. It has 35 pounds of holding force at nominal input voltage. Maximum current draw is .020 A @ 24 volt and 120 volt, and .030 A @ 12VDC.
LCN part number SEM7820-516
SEM7820-516 -
Von Duprin 2227 Top Vertical Rod 109361
The Von Duprin 2227 Top Vertical Rod 109361 will work on all 2227's up to door heights of 7'1". The actual length of the rod is 37-3/8", less the fittings. If your door is taller you will need a rod extension. Call 1-800-642-2403 for longer top rods or rod extensions.
Von Duprin part # 109361
G22VR60-
