Search results for: 'exit door panic devic steel parts'
-
Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6 -
Norton Door Closer 7700 Series Power Track Arm
Norton 7700 Series Power Track Arm
Arm is shipped will all of the necessary hardware. This assembly includes the 7701ST-1AT Adjusting Head and Tube Assembly, and the 7701ST-1AR Adjusting Rod Assembly. The square shaft measures 7/16" x 7/16". The aluminum finish ships within 24 hours, dark bronze will take a little longer.
Norton Part # 7701ST-1A
7701ST1A- -
Adams Rite Cylinder Dogging Assembly 31-0265-01-IP
The Adams Rite 31-0265-01-IP is used on the current versions of their devices for Cylinder Dogging. Cylinder Dogging is when you have a Mortise Cylinder to lock the device in the unlocked positions (Dogged). Very similar to the Hex Key Dogging Assembly, but the mounting plate is longer.
G31026501IP -
Floor Door Stop Dome 1-3/8" FS438
Floor Door Stop Dome 1-3/8" FS438
We ship the H.B. Ives FS438 Floor Dome Stop, another product made by Ives that has been around for 50 plus years. Take a walk around a school made in the 1960's and you will probably find this door stop, or the hole were it used to be. This Dome Stop is used on doors without thresholds that have a bottom of the door to floor clearance of less than 5/8". The are constructed of cast aluminum or cast bronze depending on the finish you are looking for. The rubber stop is non-marring and replaceable. The stop has a base that is 1-3/4" x 2" oval, an overall height of 1-3/8" and a base height of 9/16".
GJFB14- -
Command Access MLRK-VD Motorized Latch Retraction
The Command Access MLRK-VD Motorized Latch Retraction is for use on the 33,35, 98 or 99 Von Duprin Exit Devices. This motor is 24 to 28 volts and has a Standard : 900 mA (Avg Current Peak); 215 mA (Avg Current Hold). This unit requires 18 ga wire. And ships with (1) Motor Mount with MM5; (2) 40002 - 8/32 x 1/4 inch Phillips Head Screw; (1) 50030 8/Lead with vd Connector; (1) 50944 Molex Pigtail; (1) 40144 Dogging Hole Cap; (1) 50991 Fire Rated Drilling Template; (1) Replacement Dogging Tail Piece.
The MLRK1-VD is a cost-effective and straightforward way to upgrade your Von Duprin 33/35 & 98/99 series device to motor-driven latch retraction in the field. For AX devices, see the MLRK1-VDAX listed on the cutsheet below. UL Listed + 3 Year Warranty
MLRK1-VD -
Door Pull Handle 16
The Door Pull Handle 16 has an overall length of 7-1/2". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.
GHE16- -
Falcon 2390 231CA Cylinder Kit
The Dor-O-Matic 2390 231CA Cylinder Kit converts your 2390 exit only to a Night Latch or Hold Back function key lock. All the hardware is included in the package to convert your device, except for the Mortise Cylinder. Housing measures 4-1/2" tall by 1-11/16" wide with a 1-1/8" projection. We send the 231CA which includes the Schlage B502-191 Cam. The 239CA is the same kit, but without the Schlage Cam.
Discontinued item, we only have a few left in Dark Bronze.
231CA- -
Norton 9300 Door Closer-Discontinued
Norton Door Closer 9300
- Spring size 2, 3, 4, 5
- Separate and independent valve for sweep speed and latch speed
- Adjustable backcheck standard
- Regular, top jamb, parallel mount
- Friction hold open arm optional
- UL listed and compliant with UL10C for positive pressure
- 5-year limited warranty
- ANSI/BHMA A156.4 Grade 3
3/4" x 9-1/16" Hole Spacing
In April of 2023 Norton Yale have discontinued the 2300 and 9300. The Norton 1600 will be sent in place of the 2300. Same Hole Spacing, but adjustable spring tension.
9300- -
Cal-Royal 4500 Series Lever Trim
The Cal-Royal 4500 Series Lever Trim is for use on the 45-RIM and 45-SVR Exit Devices. The Lever Trim is non handed and ships with a 6-pin C Keyway Cylinder. The function is Classroom, which means the key will lock or unlock the lever. The lever also incorporates a clutch function so the mechanism will not break when excessive force is applied to the lever.
ESC45- -
Von Duprin 6000 Series Solenoid Kit
The Von Duprin 6000 Series Solenoid Kit is used to replace burnt out solenoids on there 6000 series. To order determine the voltage and whether you have fail safe or fail secure.
Part # 050237 12 VDC (Fail Safe & Fail Secure)
Part # 050239 16 VDC (Fail Safe & Fail Secure)
Part # 050240 24 VDC (Fail Safe & Fail Secure)G0502xx -
Norton 6870T-8 CloserPlus Hold Open Arm
Norton CloserPlus Hold Open Arm
This heavy duty Parellel Arm can be used with the Norton 1600, 9300, 8000 and 7500 door closers. The knob on the main are locks and unlocks the arm to hold your door open.
Aluminum is in stock, Dark Bronze is 2-3 week lead time.
Norton Part # 6870T-86870T-8- -
Continuous Full Surface Geared Hinge
The Ives 157XY Continuous Full Surface Geared Hinge is an ideal solution for the replacement or worn or broken storefront door pivots, which we run across quite often. I our opinion this is the best solution if you can not find a compatable replacement pivot. The geared hinge will not allow the door to twist, which makes your door more sturdy in the frame. This hinge measures 83" long and is 3-7/16" wide included the cover which hides the screw mounting. A patented easy to install, heavy duty hinge which offers lateral and vertical adjustablility whle the door is still hanging. The hinge is non handed, will mount on a narrow frame, can be cut down in the field and will work on doors up to 550 pounds. 12-24 x 1/2" steel self drilling and tapping screws are included.GFS102- -
Wall Door Stop / Holder WS45
The Ives Wall Door Stop / Holder WS45 was introduced about 50 years ago as the Glynn-Johnson W45A or GJW45A. When they were purchased by H.B. Ives, it became the WS45. They are constructed of cast Brass or Bronze and then plated to the desired finish. This door stop is unique because the wall does not have to be parallel to the door for it to latch and hold the door open. Spring loaded roller rides up the face of the strike, seating itself on the strike, holding the door firmly in the open position. A heavy rubber pad cushions the shock and absorbs the sound. With unit mounted on door and the strike on wall, vertical adjustment is available on body. The strike is adjustable 45 degrees left or right, both adjustments easily accomplished at time of installation or at a later date. WS45 strike is furnished with wood screws for drywall mounting.
GJW45A- -
Plunger Door Holder / Stop DH6000
The Plunger Door Holder / Stop DH6000 is one of the most common plunger style door stops we offer. They are constructed of a cast zinc alloy that is then electro statically painted to either an aluminum or dark brown color. It features a non marring rubber tip that is replaceable, and we keep in stock. The body measures approximately 7" long and is 1-5/8" wide. The throw on this stop is 1-1/8". These are sometimes called pop-up or push down door stops. This product ships with the mounting screws.
Made by International Door Closer
GDH6000- -
Wall Door Stop / Holder WS20
The Ives Wall Door Stop / Holder WS20 is another door holder from Glynn-Johnson. The Chicago based manufacture made these for 40 plus years. When they were purchased from H.B Ives and merged into there line they became the WS20. This holder is constructed of cast brass and then plated to your desired finish. The hinged holding clip can be released by a gentle pushing on the door, which causes the clip to flip up and release the door. The piece ships with wood screws and anchors.
GJW20- -
4" Kickdown Door Holder FS455
4" Kickdown Door Holder FS455
The H.B. Ives FS455 is what people think about when they say Kick Down Door Stop. This design has been around for almost 50 years and is try and true. Durable and ascetically pleasing to look at. This door holder features a simple hold and release, activated with a touch of the foot. They are constructed of cast brass or aluminum depending on the finish that you are looking for. The rubber tip is a non-marring and is corrugated on the bottom so it will not slide on the floor, and is easily replaceable, look under related products for the replacement shoe. This holder is for door to floor clearances of less than 2". This is an ideal door holder for the home, office, church or school.
Made by H.B. Ives
GJ44- -
Corbin Russwin Door Closer DC8210
Corbin Russwin DC8210 Door Closer
Applications
High-quality products and innovative designs are the foundation for the long
history and reputation of Corbin Russwin Architectural Hardware. That tradition
continues with the Grade 1 DC8000 Series door closer, the perfect choice for
high-use openings and doors that must meet ADA requirements. A variety of
arms, finishes and quality features make the easy-to-install DC8000 ideal for
schools, office buildings, health care facilities and retail complexes.DC8210- -
Dor-o-Matic 1690 Actuator Arm Brkt Assembly PB338
The Dor-o-Matic Falcon Actuator Arm Bracket Assembly is used on the 1690 and 2390 devices.
Doromatic part # BRKTASY.107 or PB338
Dor-o-Matic 1690 Repair Parts Breakdown
GPB338