Search results for: '1900 ingersoll ring dopanic door handle parts longmushroom'
-
Rixson 119 Intermediate Hinge
• Not load-bearing
• Available 3/4"(19mm) offset only
• Non-ferrous base material
• Used with 117, 117-1/4, 195, UNI closers,
127 closer
• Maintains door alignment
• Furnished with wood and machine screws119 -
Yale 1500 60-1500-1184 Dogging Shaft
Yale 1500 60-1500-1184 Dogging Shaft
Used on the Yale 1500 Rim and Surface Vertical Rod Devices. This is the peice that the Dogging Key goes in to actuate the Dogging Piece. The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter. The hex is 5/32"
Yale Part # 60-1500-1184
G6015001184 -
Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558 -
Von Duprin 9927 Rod Guide Assembly 112063
The Von Duprin 9927 Rod Guide Assembly 112063 works on all of the Von Duprin 98 and 9927's. The guide keeps the rods from bowing or getting bent by hand carts, or rowdy patrons. Replaces the old style which had the cover and springs.
Von Duprin part # 112063
G99VR35- -
Jackson Panic Device 1085 And 1095 Dogging Pin
The Jackson Panic Device 1085 And 1095 Dogging Pin is the piece that keeps the hardware in the open position during business hours. It is activated by pressing the crossbar and then turning the flat head screw driver head. The pin is held in the housings with a screw, which is located on the back of the housing. This pin has been used since about 1988 or so, the old style are no longer made, but they had a roll pin that was used to hold it in place. This package comes with a new spring, set screw and the pin. The Jackson part number on this is 30-1115.
G108554 -
Detex Advantex 40 Series Narrow Stile Rim
The Detex 40 Series rim exit device is a supper heavy duty panic device for use on narrow stile doors. Device features an angled end cap to deflect damage away from the unit. This device is designed for years of trouble free service in high use, high abuse enviroments.
G40REO- -
Sargent 624 Bottom Surface Strike
The Sargent 624 Bottom Surface Strike is used on the 20, 30, 60, 80 and 90 Series Surface Vertical Rod Panic Hardware. The Strike is mounted on the floor and the bottom latch locks on to it. Strike measures 9/16" x 2-1/2" with a 3/8" projection. Strike features a black coated epoxy.
Sargent Part #624
G624 -
Push Bar Adjustable 452
Push Bar Adjustable 452
Finishes:
US26/625 polished chrome
US26D/626 brushed chrome
US3/605 polished brass
US4/606 brushed brass
US5/609 antique brass
US10/612 brushed bronze
US10B/613 dark bronzeMaterial: Brass
Material Size: 5/8" round tube adjustable to 36"
Base: 5/8" x 8-1/2"
Clearance: 1/2"
Projection: 1-1/8"452- -
Jackson Panic Device 2085 Dogging Assembly RH/LHRB
Jackson Exit Device 2085 Dogging Assembly RH/LHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2467
This spring would be for the Device on the Left, shown below.
G302467 -
Dor-o-Matic 1690/1990 Top Strike Shim Package-SHIM.112
Doromatic PB48 Strike Shim Package Of 10 Pieces
This Dor-o-Matic product is for the PB48 Top Strike. This is the shim that goes under the top strike. The plate measures 1" x 1-1/16" with 4 holes. The mounting holes are 11/16" x 11/16" on center. They are only sold in packages of 10.
Doromatic Part # SHIM.112
G199034-SHIM -
Jackson Panic Device 2085 Dogging Assembly LH/RHRB
Jackson Exit Device 2085 Dogging Assembly LH/RHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2462
This spring would be for the Device on the Right, shown below.
G302462 -
Von Duprin Panic Device 210NL Trim
The Von Duprin Panic Device 210NL Trim is part of there economy series trims. This trim iis a pull with a key cylinder hole, it will line up with the chassis mounting holes of the 22 and 2227 devices. The key locks and unlocks the exit device. The plate measures 5-3/8" x 4-25/32" x 3/32", with a projection of 1-31/32".
220NL -
Falcon 650387 Bottom Bolt Guide Assembly
Falcon 650387 Bottom Bolt Guide Assembly
The Falcon Monarch Bottom Bolt Guide Assembly 650387 is used the 19-V, 24-V, 25-V and the XX-V Bottom Rod. The Guide Assembly measures 1-7/8" tall by 1" wide and projects 1-9/16" at the widest projection. The Bottom Bolt Guide is made of zinc plated steel.
Falcon Monrarch Part # 650387
G650387 -
Door Push Plate 50
The Door Push Plate 50 is the most common push plate we find out in industry today. It does not matter what type of commercial building you go into, you will find this style and thickness plate. The are offered in standard sizes, that are shown below, and can be made to custom sizes. The plates are 16 gauge metal (.050 thick) and are shipped with 4 beveled edges. The matching finiish screws are shipped with each plate.
3 x 12" GPH312
3.5 x 15" GPH315
4 x 16" GPH416
6 x 16" GPH616
4 x 20" GPH420
8 x 16" GPH816GPH50 -
Von Duprin 22 Metal End Cap 900397
The Von Duprin 22 Mechanism Metal End Cap 900397 is new for 2016. This new kit replaces the 900397 with a metal end cap, which is has always been a weak link of the 22 series. The package includes the End Cap, Bracket and the Mounting Screws. This cap and bracket will work on all of the 22 and 2227 series.
Von Duprin part # 900397
G22R10M- -
Sargent 8700 Panic Device
For Doors Wood or metal. 1-3/4" (44 mm) thick standard.
minimum stile with trim and 3-1/2"
Mounting Supplied standard with wood and machine screws
Chassis Cover Cold drawn brass, bronze or stainless steel
Chassis Nonferrous alloy
Hand Handed. Specify RHRB or LHRB
Dogging Feature Allen-type dogging furnished standard.
Top and Bottom Bolts Brass, stainless steel8700EO -
HES 5000 Electric Strike Package
The HES 5000 Electric Strike Package is a compact, high performance electric strike designed for low profile openings where there is limited space behind the jamb. Its strength is derived from a unique keeper pin locking design, enabling the 5000 to exceed the ratings of the frame, door and locking hardware. This field selectable fail secure/fail safe unit is easy to install and accommodates latch bolts up to 5/8" throw.
5000C -
Sargent Exit Device 80 Series Plastic End Cap And Bracket
Sargent Exit Device 80 Series Plastic End Cap And Bracket
includes the end cap, bracket and mounting screws. This plastic end cap always breaks. You might want to consider trying the new impact resistant end cap shown in the related products, on the right hand margin of the page.
Used on the Sargent 80 Series Exit Devices
Part #'s 68-0561, 68-0511 and 97-0052
G80300 -
Doromatic 2390 Moving Pushbar End Cap PB342 ECAP.143
Discontinued December 2024
Doromatic 2390 Moving Pushbar End Cap
Doromatic 2390 Moving Pushbar End Cap is the piece that fits on the end of the pushbar. The Endcap is 3-3/8" high by 1/4" thick, with an 1-7/8" projection. The Pushbar End Cap is constructed of die cast metal that is painted black.
Doromatic / Falcon Part # PB342 or ECAP.143
GPB342 -
Von Duprin 55 Dog Screw-090053
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
Von Duprin part # 090053
55R85 -
Von Duprin 2227/3327A/9927 Top Latch 050400
The Von Duprin 050400 Top Latch is used on the 2227, 3327A, 3427A, 9827 and 9927 exit devices. It is used the Fire-Rated along with the standard Panic Devices. The 050400 is sold without the the Mounting Bracket, if you need the Mounting Bracket you can order the 050546, or order the G99VR10 (050091) which will come with the Bracket. This latch is for use on devices shipped after October 1998. This is usually the problem if your bottom rod is dragging on the floor. Includes screws.
Von Duprin Part # 050400
G050400 -
Von Duprin Strike 299F
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
Von Duprin Part # 299F
299F -
Detex ECL-230X Alarmed Deadbolt Panic Hardware-Single Point
The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm. The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.
ECL-230 -
Lock Guard Standard Line
• Ideally suited for use with rose or escutcheon 2-3/4" wide or less.
• For use with Type 86 Mortise and Type 161 Cylindrical Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.2-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2"1625- -
Detex ECL-230D-PH Alarmed Panic Device
The Detex ECL-230D-PH Alarmed Exit Device is a battery operated, rugged deadbolt panic device, and is UL-Listed Panic Hardware for 36" to 48" doors. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force, and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
ECL230DPH- -
Cal Royal Panic Device 7700 Rim Device
Cal Royal 7700 Rim Exit Device
For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware. Uncompromising security and safety in single and double fire exit doors. Chassis mounted unit construction. Rim and vertical rod devices are non-handed and easily reversible. Available in many different functions. Lever and escutcheon trims are grade 1 construction with clutch free-wheeling mechanism. Rose and escutcheon covers 161 cut out.
Templating matches the Von Dupin 99 and 98
CR7700EO- -
Von Duprin 107765 Plunger Release Bracket
The Von Duprin 107765 Plunger Release Bracket is used with the Fire Rated 8827-F Top Latch. When the door closes, the Release Pin on the 88VR10-F (050462) hits the post and releases the latch from the retracted position. Once the top latch is released, it drops the bottom latch into the floor.
Von Duprin # 107765
G107765- -
Detex ECL-230D Alarmed Panic Device
The Detex ECL-230D Alarmed Exit Device is a battery operated, rugged deadbolt panic device. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
If you have a door that requires Panic Hardware, then use the ECL-230D-PH
ECL230D- -
Push Bar Adjustable 450
Push Bar Adjustable 450
Finishes:
US3/605 Polished brass
US4/606 Brushed brass
US10B/613 Dark bronze
US26/625 polished chrome
US26D/626 brushed chromeMaterial: Brass
Material Size: 5/8" Rd Tube Adjustable up to 36"
Clearance: 1/2"
Projection: 1-1/8"
Fasteners: Surface Mount only450- -
Lock Guard Slim Line
• Designed for use on all Type 161 Cylindrical Locks (ANSI 156.2 Series 2000)
Monolock and Unilock.
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating the
opening between door and frame at latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.1-1/2" Wide x 7" High
Stud center to center: 4-1/2"1625SL- -
Sargent 2727 Panic Device
Simplicity
• Engineered with minimum components and maintenance-free
• Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
• Retrofits to all applications
• One chassis design to accept all available functions/trims
Durability
• Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
• Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
• Non-handed rim; reversible vertical rod
• Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
• Three year warranty2727EO- -
Cal Royal GLS7700 Narrow Stile Rim Device
The Cal Royal GLS7700 Rim Device is for use on Aluminum Framed Glass Doors when the Stile width is 1-3/4 inch or more. The exit device ships with wood and machine screws, along with the Strike plate. The stainless steel latch bolt has a 3/4 inch throw. This device is a Grade 1, which is the heaviest duty rating.
GLS7700-