Search results for: 'dorma swing door cap dent minimum von'
-
Rixson 27 Series Door Closer
• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustmentWhen Less All Parts is selected only the Cylinder is shipped, just the replacement hydraulic cylinder will be shipped
27-RIX -
Von Duprin Panic Device 880K Trim
The Von Duprin Panic Device 880K Trim is for use with the 88 series devices only. Plate measures 3" wide by 14-3/16" long with an 1-5/8" diameter bore for cylinder. Knob projects out 2-3/4". We do not sell many of these anymore, due to ADA requirements, but they are still available.
88K- -
Von Duprin QEL Baseplate Conversion Kit
The Von Duprin QEL Baseplate Conversion Kit is for use on the 33A, 35A, 98, and 99 exit devices. The size is the size of the exit device. The 98/99 device 36" would be 33" wide device and the 48" would be for the 45" device. The 33A/35A the 36" would be for the 35-3/8" wide device and the 48" would be for the 47-3/8" wide device.
Von Duprin Part # 958003 3' Device
Von Durpin Part # 040065 4' DeviceG95800x -
Von Duprin 99 Rim Center Case 050020
The Von Duprin 99 Rim Center Case 050020 replaces all previous versions of the Von Duprin 98/99 Rim Device Center Cases. One of the best things about a Von Duprin is when they redesign a part, they make it so your old device is not obsolete and you can update your device. All internal parts, springs, screws and cover mounting bracket included.
Von Duprin Part # 050020
G99R15 -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
Von Duprin 110388-00 6 Foot EL Cable Assembly
The Von Duprin 110388-00 6 Foot EL Cable Assembly connects directly into your power source and the Potted Circuit Breaker 050534. This 6 foot Cable Assembly is used on Von Duprin and Falcon Exit Devices that have the Electric Latch Retraction.
Von Duprin Part # 110388-00
G110388 -
Von Duprin Strike 264
The Von Duprin Strike 264 measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.
Von Duprin Part # 264
264 -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50- -
Von Duprin 100316 5547 Top Plate
The Von Duprin 100316 is used on the 5547 on the top of the door. The top rod goes through the square hole on the plate. The plate shown in the Picture has both sides or LHR and RHR doors. One side of the strike is usually broken off depending on the hand of the door.
G100316 -
Von Duprin 88 Lever Arm Right Hand 050438
The Von Duprin 88 Lever Arm Right Hand 050438 replacement lever arm for all the Von Duprin 88 exit devices. Usually replaced due to the dogging screw stripping out. The arm includes the Wedge, Wedge Ring, Wedge Tite Screw and Dog Screw, and sometimes the axle.
Von Dupin part # 050439
Old Part # 10072988R80- -
Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6 -
Von Duprin Panic Device 99 Lever Trim
The Von Duprin Panic Device 996L Lever Trim has an escutcheon plate that measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". The key cylinder, not included, locks and unlocks the lever. This lever handle is handed, but is field reversible. Key lock and unlocks lever. We ship the 996L-R&V
99L -
Von Duprin 050500 88 Latch Tail Kit
Von Duprin 050500 88 Latch Tail Kit
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
Von Duprin Part # 050500
G050500 -
International 8710S Narrow Design Rim Device
The International Door Closer (IDC) 8710S is a narrow design rim device. The minimum stile width has to be 2-19/32 inches. The device features a 3/4 inch throw deadlocking latchbolt, hex key dogging, and ships with machine screws and strike. The device is Grade 1 Rated, which is the highest rating possible. The 36 inch device is 33-15/32 long and the 48 is 44-3/4 inches.
8710S-
