Search results for: 'allen wrench lock part on a push bar door keys push b'
-
Von Duprin 8827 Top Latch Case 050460
The Von Duprin 8827 Top Latch Case 050460 is for non fire rated doors. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted position.
Von Duprin part # 050460
Old Part # 10175088VR10 -
Dor-O-Matic 1690/1790/2390 Dogging Assembly PBX-16
Dor-O-Matic 1690/1790/2390 Dogging Assembly PBX-16
Falcon Doromatic 1690, 1790, and 2390 replacement dogging assy. The dogging assembly is used to dog the door in the open position, so people can enter the building without having to unlatch the door for the inside or with a key on the outside. The KIT.1197 comes complete with mounting screws. Some of the earlier version where riveted into the rail, so you might need to drill out the rivets, the screws shipped with KIT.1197 have self tapping thread forming screws.
Doromatic part # KIT.1197
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts Breakdown
Falcon / Dor-o-Matic 2390 Parts Break DownGPBX16 -
Von Duprin 6113 24 VDC Electric Strike
Von Duprin 6113 24 VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The 6113 has a 3/4” latch bolt throw, 6” face plate length, 1-5/8” width, and an 1-15/16” backbone depth. The lock retrofits the VD 3011 and VD 3021. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6113 -
Ives Surface Bolt 8" SB453
The Ives Surface Bolt 8" SB453 has a 1-3/16" throw. The bar has a cross section measurement of 3/4" wide by 1/4" thick. It features a strong tension springs to prevent the bolt from creeping. The bolt is shipped with all of the fasteners and a universal top and a standard mortise strike. It is constructed of heavy duty steel that is then cadmium plated.
Ives part # SB453-8-TB-2C
GSB82C -
Glynn-Johnson 79 Series Overhead Door Holder Surface Mounted
The Glynn-Johnson 79 Series Overhead Door Holder Surface Mounted are constructed primarily of Brass and 300 series Stainless Steel substrates, with several components fabricated of Steel treated to resist corrosion. Models in the 70 series utilize a 1/2"-diameter stainless steel bar, while the 79 series uses a 3/4" stainless steel bar. The bar is always provided in US32D. The spring, washer and nut are provided in a clear zinc finish.
GJ790 -
Von Duprin 22 Panic Only 22EO
The Von Duprin 22 Panic Only 22EO is part of the economy series. Even though is it the least expensive Von Duprin, it is still a very heavy duty panic device. It is for all types of single and double doors with mullion, for door stiles as narrow as 3-13/16”. All 22 Series exit devices are UL listed for Panic Hardware or Fire Hardware, and are certified to ANSI A156.3, Grade 1. The Von Duprin 22 ships with the 299 standard strike, dog key, and all of the needed mounting fasteners. Even though it is the least expensive, they offer all the replacement parts, just like there other models. We stock all of the replacement parts Von Duprin has to offer on the 22 and 2227 series.
We keep the 36” devices in stock in the SP28 Sprayed Aluminum and SP313 Sprayed Dark Brown in stock.
Von Duprin Part # 22EO22EO -
Von Duprin 050536 HD-EL Solenoid
Von Duprin 050536 HD-EL Solenoid
Electric Latch Retraction for Von Duprin Exit Devices with Hex Key Dogging. #4 on the diagram below large picture.
Von Duprin part # 050536
Old Part # was 110740No longer available, the only solution we have at this time is to upgrade to the HD-QEL Base Plate.
G050536 -
Von Duprin Panic Device 230L Lever Trim
The Von Duprin Panic Device 230L Lever Trim will work on the 22 and 2227 series exit devices. In 2008 this lever was redesigned and went from a key in the lever to the new style which has the key above the lever. The plate measures 3" wide by 6-3/8" high and is 15/16" thick. This lever only comes in sprayed aluminum or dark bronze. We also have replacement parts for this particular trim piece in stock, email us under the contact tab at the top of the page.
Cylinder not included
22L -
Corner Guard 311 2" X 2"
The Corner Guard 311 are a great way to protect corners in areas of high traffic and high abuse, such as warehouses and hospitals. Fabricated from 16 gauge (.050") thick metal they measure 2" on both arms, and can come in any length. Standard lengths are 36", 42" and 48", but we have the capability to modify to your specifications. They come standard with screw mounting, but other options are available.
Screws included for mounting
GCG311 -
Dor-o-Matic 1990/2090 Crossbar Screw 1/4- 20 X 1" PB12
Dor-o-Matic 990/1090/1990/2090 Cross Bar Screw
Doromatic part # SCREW.1027
1/4-20 x 1" Self Tapping Threads
Dor-o-Matic 990/1990 Repair Parts Breakdown
Dor-o-Matic 1090/2090 Repair Parts BreakdownG199012 -
Dor-o-Matic 1790 Panic Device
The Doromatic 1790 rim device is typically used in applications where maintenance is a concern because the rim device has fewer parts and pieces than current exit devices. The result is less maintenance and adjustment. The streamlined design has no openings for chains, reducing the risk for code infringements and offering increased building security by eliminating the possibility of tampering and forced entry through the use of coat hangers and other tools. The Doromatic 1790 may also be used to retrofit a Doromatic 2090 series crossbar device.
Replacement parts are also available
Shipped with all screws and strikes. If you wish to use a key cylinder on the exterior, you will need the 1790 NL/HB Cylinder Assembly, 179CA.
1790EO -
Yale 1500 60-1500-1184 Dogging Shaft
Yale 1500 60-1500-1184 Dogging Shaft
Used on the Yale 1500 Rim and Surface Vertical Rod Devices. This is the peice that the Dogging Key goes in to actuate the Dogging Piece. The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter. The hex is 5/32"
Yale Part # 60-1500-1184
G6015001184 -
Falcon / Dor-o-Matic MEL1690 Panic Device
The same as the Falcon / Dor-o-Matic 1690 with Mechanical Electric Latch Retraction. Some of the features are listed below. A power supply is required.
Hand: Field reversible, non-handed.
Centercase and end cap are powder-coated black only.
Strikes: PB48 top.
Latches: Hex bottom latch (standard), RL - rod bottom latch, PL - Pullman bottom latch
Cylinder: Rim, key entry (NL) or hold back (HB) feature available.
Field selectable.
Sizes: 30", 36", 42", and 48".
Doors: 1-3/4" thick metal doors, specify if other.
Projections: 3-3/8" in neutral position, 23/8" in dogged position.
Pushbar height is 2-1/2.
Stile: 1-3/4" minimum.Replacement parts are also available
Shipped with all screws and strikes.
MEL1690EO- -
Von Duprin 99 Cover Plate 050114
The Von Duprin 99 Cover Plate 050114 is for use on the 33A, 35A, 98 and 99 devices. Covers the dogging assembly on the hinge side of the door. The usually fall off when the End Cap is not on the exit device. Von Duprin is only shipping a 20-1/2" cover plate now, which will work on 3' and 4' doors, you will have to cut more off if you have a 3' device with a hack saw or chop saw.
Von Duprin Part # 050114 and 050117 Hex Key Dog Conversion Kit
Von Duprin 99 Cover Plate 050114
G99R50 -
Von Duprin 8827 Bottom Latch Case 050461
The Von Duprin 8827 Bottom Latch Case 050461 is used on all Von Duprin 8827 non fire rated exits. A non fire rated device is one that has to positively latch every time it closes, you can usually tell, because a non fire rated device has the hex key dogging. Included mounting screws.
Von Duprin Part # 050461
Old part # 10175188VR170 -
Ives 7212 Pivot Set
• Handed
• Top, header mount
• Bottom, jamb mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking7212 -
Ives 7222 Pivot Set
• Handed
• Top, header mount
• Bottom, base plate mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking7222 -
Von Duprin 88 and 55 Wedge Tite Screw 090081
The Von Duprin 88 and 55 Wedge Tite Screw 090081 is used on the 55 and 88 panic hardware. This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite. The screw is a 5/16-18 x 5/8 hollow set point.
Von Duprin Part # 090081
88R100 -
International 8710S Narrow Design Rim Device
The International Door Closer (IDC) 8710S is a narrow design rim device. The minimum stile width has to be 2-19/32 inches. The device features a 3/4 inch throw deadlocking latchbolt, hex key dogging, and ships with machine screws and strike. The device is Grade 1 Rated, which is the highest rating possible. The 36 inch device is 33-15/32 long and the 48 is 44-3/4 inches.
8710S- -
LCN Door Closer Cover
The LCN Door Closer Cover is the standard plastic cover that ships with LCN Door Closers. Specify your current closers model number when ordering. Not all of the LCN closers have the same shape cover on the door closer cylinder. The part number is the Series Number followed by -72. So, the part number would be 1460-72, 4010-72, 4020-742, 4030-72, 4040-72 and 4110-72. We have access to all the covers, if yours is not here call us and we will quote you a price.
4XXX-72 -
Door Sweep 1" Long Rubber
The Door Sweep 1" Long Rubber has an over height of 1-7/8", with 1" of it being the gray rubber seal. The mounting rail is constructed of extruded aluminum and is available in aluminum or dark brown finishes. This sweep ships with screws.
International Part # IDC-97V
IDC97V- -
Norton Door Closer Arm Shoe Assembly
Norton / Yale Door Closer Arm Shoe Assembly
Replacement Shoe Assembly for Norton 1600, 9300, 7500 and 8000 series door closers. And Yale 50, 2300, 8000 and 4400 series.
Base measures 11/16" x 2-1/4" with 1-3/4" center to center screw hole mounting. Bracket projects out 15/16". The pin is 3/8" diameter.Norton part # 7701AS or a Yale # 400-AS
Old Norton Part # 1620AS
7701AS- -
Jackson 1095 Panic Rim Device
The Jackson 1095 Panic Hardware was one of the first devices universally recognized as the standard for aluminum storefront hardware. Made of high tensile strength aluminum. It ships complete with both housings, crossbar, all the fasteners, and the strike. Comes with 45" cross bar that is easily cut in the field.
1095EO -
SEM-7800-825 Armature for LCN Electro Magnetic Door Holder
The SEM-7800-825 Armature for LCN Electro Magnetic Door Holder is the door mounted piece for th LCN SEM7820-825 / SEM7830-825 / SEM7840-825 / SEM7870-825 series. It features a metal die cast construction armature. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". Available in an aluminum or dark bronze color. LCN Part # SEM7820-825, SEM7830-825, SEM7840-825, and SEM7870-825
SEM7820-825- -
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Sargent 624 Bottom Surface Strike
The Sargent 624 Bottom Surface Strike is used on the 20, 30, 60, 80 and 90 Series Surface Vertical Rod Panic Hardware. The Strike is mounted on the floor and the bottom latch locks on to it. Strike measures 9/16" x 2-1/2" with a 3/8" projection. Strike features a black coated epoxy.
Sargent Part #624
G624 -
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The model 6111 retrofits model number VD 3031, and measures 1-5/8” wide, 6” high and has a backbox depth of 1-3/4”. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6111 -
SEM7850 LCN Electro Magnetic Door Holder
The SEM7850 LCN Electro Magnetic Door Holder features a metal die cast housing that is surface wall mounted. Tri-voltage design works with 12, 24 or 120 volts, with 35 lbs. of holding force. The magnet housing measures 2-13/16" wide by 4-5/8" high. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". The total projection of both pieces is 3-5/8". Available in an aluminum or dark bronze color. Armature extensions are available, along with replacement covers, magnets, and armatures. Outlet box not included
LCN Part # SEM7850
SEM7850- -
SEM7820 LCN Electro Magnetic Door Holder
The SEM7820 LCN Electro Magnetic Door Holder features a metal die cast housing that is surface mounted on the floor. Tri-voltage design works with 12, 24 or 120 volts, with 35 lbs. of holding force. The magnet housing measures 5-1/8" long x 4-9/16" wide and 3-7/16" high. The armature (door mount part) is 1-11/16" wide by 2-3/8" high with a 1-7/8" diameter. The armature projects out 1-5/8". The total projection of both pieces is 6-3/4". Available in an aluminum or dark bronze color. Armature extensions are available, along with replacement covers, magnets, and armatures.
LCN Part # SEM7820
SEM7820-