Search results for: 'guard specialties 60 z door hold'
-
Sargent 20/30/60 End Cap Bracket
The Sargent 20/30/60 End Cap Bracket is used with the larger end cap. This end cap has been manufactured for the last 40 years and started its life on the obsolete 60 Series. The bracket holds the hinge side of the exit device on the door, and the G20300C fits over the top of it.
Sargent part #68-2141
G20300B -
Ives LG1 Lock Guard
The Lock Guard with Security Pin is ideal to cover the latchbolt area of the door, lock and frame, with the added protection of a security pin to prevent separation of the door and door frame. The plate is through bolted with carriage bolts and nuts, which are included with the guard. The plate is constructed of 13 gauge stainless steel. The plate measures 3" wide and 11-1/2" high, with a center to center on the mounting bolts of 10-1/2".
Ives Part Number LG1-US32D
LG1- -
Von Duprin 2670 Guard-X Panic Device
Heavy Duty Design
The new Series 2670 Exit Alarm Lock provides secure protection through a large stainless steel deadbolt, which is 2" x 1/2" (51mm x 13mm) and has over a 3/4" (19mm) throw. The engagement area into the strike is over 1 1/4" (32mm) square inches. The cast aluminum latch case protects the internal mechanism and resists tampering or vandalism from inside the door. This unit has been tested to withstand up to 1600 pounds of static load force against the door.Fits 36" to 48" doors.
Uses 9 volt battery
Ships with all mounting hardware and strike.2670EO- -
6" Kickdown Door Holder Grand Standard
6" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 5-3/8" to the Floor when mounted.
Made by Grand Specialties 606z and 606br
606BR is not longer manufacturedGJ606 -
10" Kickdown Door Holder Grand Standard
10" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 9-3/8" to the Floor when mounted.
Made by Grand Specialties 610z
GJ610 -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
12" Kickdown Door Holder Grand Standard
12" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed rubber shoe can be adjusted down as the rubber shoe wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 11-3/8" to the Floor when mounted.
Made by Grand Specialties in USA Part # 612z
GJ612 -
Offset 60 Degree Door Pull 36-1 inch diameter
The Offset 60 degree Door Pull is available in 8, 10 and 12 inch centers. The handle is constructed of 1 inch solid material, with the base metal determined by the finish (color). It features 1-1/8 clearance, 2-1/8 projection and has a 2 inch offset. The fasteners are 5/16-18 thru bolts with a finish washer. Please specify the door thickness when ordering.
GHE36- -
LCN Door Closer 4111 HCUSH Hold Open
LCN Door Closer 4111 HCUSH Hold Open
Standard 4110 series closer shipped with HOLD OPEN CUSH N STOP arm, standard plastic cover, 4110-201 FIFTH SCREW SPACER and self reaming and tapping screws. Sized cylinders adjustable for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Closer mounts parallel arm, specify right or left swinging door. 4111 cylinder meets ADA requirements. The cush hold open arm allows for a stop and hold open positions up to 110 degrees. "T" handle on arm will release door for closing, locking pin can be retracted for normal door closing operation.
We ship the 4111 HCUSH
4110HCUSH- -
Door Push Plate 60
The Door Push Plate 60 has the classic half round design. The plate measure 8" wide and 16" tall, and is constructed of 16 gauge metal, which is .050" thick. This plate is similar to the GPH59 (Push Plate 59), but is a 1/2" wider and 1" taller. This plate ships with the matching finish screws.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GPH60- -
5" Kickdown Door Holder Grand Standard
5" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.
made by Grand Specialties 605z 605b
GJ605- -
International Door Closer 200 Series Overhead Concealed Closer
The International Door Closer 200 Series Overhead Concealed Closer has been in there line up for at least 20 years. It is designed as a replacement for the Jackson 20-330 concealed closer. This closer is a fixed spring closer with two adjustment valves, one for closing and one for latching speeds. It has a built in positive back stop and hold open positions, if you order the hold open option. To order select the desired opening swing (90 or 105 degrees) and hold open or non hold open. This is just the hydraulic cylinder, the arms are sold separately.
2000-B-230 105 with Hold Open
2000-B-231 105 with No Hold Open
2000-B-232 90 with Hold Open
2000-B-233 90 with No Hold Open2000-B -
LCN Door Closer 4111 HEDA Hold Open
The LCN Door Closer 4111 HEDA Hold Open is known as the Smoothee, and is one of the heaviest duty door closers made, the HEDA stands for Hold Open Extra Duty Arm. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 HEDA model, which is a hold open arm on this page. The cylinder mounting holes are 2-1/2" by 6".
4110H- -
LCN Door Closer Hold Open Arm 3049
The LCN Door Closer Hold Open Arm 3049 has an adjustable nut that allows the door closer arm to lock when they reach a pre select position. This arm can be used on most LCN Door Closers because the Hold Open function is in the arm. If you have a regular armed LCN Closer currently, you can use this arm to make them have the Hold Open function. Two words of warning, they can not be used on an interior fire rated door, and Hold Open arms usually break. The manufactures sell more door closers with regular arms, but we tend to sell more Hold Open arms, meaning they wear out or break a lot easier then Regular Arms.
Specify your current closers model number when ordering.
Not all of the LCN closers have the same shape spindle on the door closer cylinder. The LCN Part #'s on this Regular Arm is: 1260-3049 (non handed), 1460-3049 (non handed), 4010-3049 (handed), 4020-3049 (handed), 4040-3049 (non handed). The fitting for the 4040 is a six sided, the 4010, 4020 and 4110 have a flat sided oval, and the 1260 and 1460 have an eight sided star.3049-- -
4" Kickdown Door Holder Brass Deluxe
4" Kickdown Door Holder Brass Deluxe
Popular priced crafted holder for interior doors.
Has 1/2" adjustment and replaceable steel re-inforced
shoe for long life. Made of steel with brass plated finish.Made by Grand Specialties
GJ6A -
International 300 Series Adjustable Power Door Closer
The International 300 Series Adjustable Power Door Closer is one of there new closers to meet ADA requirements. With this door closer you can adjust the spring tension, closing and latching speed, even after it was installed. The Spring Power is adjustable all the way down to 8-1/2 pounds of resistance, making it ideal for areas with the elderly and children.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
Norton Door Closer 7701-13 Hold Open Loop Assembly
The Norton Door Closer 7701-13 Hold Open Loop Assembly is usually the part that breaks on the Norton 1600, 9300, 8301, 8501 and 7500 Hold Open Door Closers. The cast iron piece attached to the disk is where they usually break. This part has had a few part numbers over the years, for Norton it has been known as the 1620-13 and 7701-13, and for Yale the 400-13.
16H300- -
LCN Door Closer Cush-n-Stop Hold Open Arm 3049CNS
Provides hold-open function with templated stop/hold-open points.
Handle controls hold-open function.Specify your current closers model number when ordering. Not all
of the LCN closers have the same shape spindle on the door closer
cylinder. This LCN Arm is known as these part numbers: 1260-3049CNS, 1460-3049CNS, 4040-3049CNS, 4110-3049CNS3049CNS -
Falcon / Doromatic Door Closer 3049/PA Hold Open Arm Only
Doromatic Door Closer Hold Open Arm Only
Doromatic Door Closer Hold Open Arm. Includes everything is the image. Can be used to convert you regular non hold arm to a Hold Open Door Closer. Arm holds the door open when door is rotated open. The hold open postion is adjustable. This is the hold open arm for the SC61 Hw/PA, SC71 Hw/PA, and the SC81 Hw/PA.
Doromatic Part numbers:
SC60 - SC60-3049/PA , SC70 - SC70-3049/PA , SC80 - SC80-3049/PADo-3049 -
Sargent Door Closer Hold Open Arm 25-H
The Sargent Door Closer Hold Open Arm 25-H is known as a Friction Hold Open Arm. As the arm rotates it tightens the two plates together until they can not turn any more, and holding the door open. To close you just pull the door and it will "unscrew". The hold open position is adjustable by tightening or loosening the larger nut.
Sargent part # 25-H
350HOA- -
ALREX Door Closer Hinge
The ALREX hinge is a full function hydraulic door closer hinge. It contains all the features of a door closer, closing and latching speed control, power adjustment, and optional hold open feature. They are available in 4, 4.5 and 5 inch (leaf height), and are currently available in Stainless and Black finishes.
Package includes 2 hydraulic closer hinges and one dummy, for a standard 3 x 7 foot door, 100 pound door.
Door Handing:
AX21 -
CG-20 Vinyl Corner Guard 2” x 2”
CG-20 Vinyl Corner Guard 2” x 2”
90 degree 2” x 2” vinyl corner guard with aluminum retainer. Vinyl flex action absorbs impact, and is .085” thick, the aluminum retainer is .062 thick. Each corner guard includes the end caps. Available in 4, 8 and 9 foot lengths. The CG-20 includes the top and bottom end caps.
CG-20- -
LCN Door Closer 4041XP-Hw/PA
The LCN Door Closer 4041XP-Hw/PA is the 4040XP, eXtra Protection closer with the 4040XP-3049 Hold Open Arm. You get the same performance of one of the most revered closers with the functionality of the friction hold open arm. The cylinder features cast iron construction, forged steel arm, double heat treated steel pinion, non-handed, LCN® “Green Dial” spring force indicator, Peel-n-Stick templates, UL and cUL Listed, 3⁄4″ journal diameter pinion, full compliment bearing, and tested and certified under ANSI standard A156.4, Grade 1. With this package you have the flexibility to mount the closer on a left, right, push, pull or top jamb mount. The hold open point is adjustable by loosening or tightening the hold open nut on the arm.
4040H- -
Rixson 28 Series Door Closer
Center Hung Door Closer
• Available (NHO) non-hold open, or (SHO) selective
hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond desired opening
degree
• Vertical and horizontal door adjustment
• Arm centering adjustment28 -
CG-10 Vinyl Corner Guard 3” x 3”
CG-10 Vinyl Corner Guard 3” x 3”
90 degree 3” x 3” vinyl corner guard with aluminum retainer. Vinyl flex action absorbs impact, and is .100” thick, the aluminum retainer is .062 thick. Available in 4, 8 and 9 foot lengths. The CG-10 Corner Guards ship with a top and bottom end cap.
CG-10- -
Clear Plastic Corner Guards 312 - 2" X 2" X 48"
The Clear Plastic Corner Guards 312 are a good way to protect corners from hand carts and dollies. If the area has a lot of traffic, like a warehouse, I would recommend the 310 or 311 which are made of metal. The are 2" by 2" and are usually 48" long, but we can do custom sizes. They are constructed of .120" thick clear polycarbonate plastic. Screws are included for mounting.
GCG312 -
Corner Guard 301 1" X 1.75"
The Corner Guard 301 are a great way to protect corners and edges of doors. Fabricated from 16 gauge (.050") thick metal they measure 1" on one arm and 1-3/4" on the other, and can come in any length. Standard lengths are 36", 42" and 48", but we have the capability to modify to your specifications. This product is ideal for high traffic or areas of high abuse. They come standard with screw mounting, but other options are available.
Screws included for mounting
GCG301 -
4" Kickdown Door Holder Grand Standard
4" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.
GJ604- -
Yale 7100F Series Latch Assy 60-7000-0425-048
Yale 7100F Series Latch Assembly
This Yale Latch Assembly is used on fire rated panic devices. A fire rated panic is a device were you can not lock the latch in the open position. It is used on doors were the engineers want the door to latch every time it closes to contain a fire.
Yale Part # 60-7000-0425-048
Note the Hub Position of this latch is the 7100
G6070000425048 -
Corbin Russwin Hold Open Arm Parallel Bracket
The Corbin Russwin Hold Open Arm Parallel Bracket is the standard bracket shipped with the Hold Open Arm. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket used by the hold open arm for parallel arm applications only. Corbin Russwin part # 509F49.
2800HPA