Manufacturers | Brushed Brass
-
Von Duprin 8827 Panic Hardware
Von Duprin 8827 surface mounted vertical rod devicesfor all types of single and double
doors, UL listed for accident hazard installations.Covers stock hollow metal doors
with 86 or 161 cutouts and fits door stiles as narrow as 3½" (90mm).- Fully reversible
- Five popular finishes
- Field sizeable
- Hex key dogging
- 5/8"(16mm)throw latch bolt
Ships with all mounting screws and the 299, 304L and 248L-4 Strikes.
8827EO- -
Von Duprin 88 Panic Device
The Von Duprin 88 Panic Device has been around since the 1950's, and is probably the device that put Von Duprin on the Map. It is designed for all types of single and double doors with mullions. It is field reversible, and ships with a 42" cross bar that can be cut down in the field. The device is dogged down with a 5/32" hex key, and ships with all mounting screws and the 299 strike.
88EO- -
Von Duprin Panic Device 880K Trim
The Von Duprin Panic Device 880K Trim is for use with the 88 series devices only. Plate measures 3" wide by 14-3/16" long with an 1-5/8" diameter bore for cylinder. Knob projects out 2-3/4". We do not sell many of these anymore, due to ADA requirements, but they are still available.
88K- -
Von Duprin Panic Device 880TP Trim
The Von Duprin Panic Device 880TP Trim is for the 88 series only. The stanchions welded on the back line up with the 88 device on the interior. The optional key cylinder locks and unlocks the thumb piece. The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.
Von Duprin part # 880TP-R
88TP- -
Von Duprin Panic Device 880NL Trim
The Von Duprin Panic Device 880NL Trim is for the 88 Series only. The stanchions welded on the back of the plate line up with the88 device on the interior. Optional key cylinder locks and unlocks the device, and can be used for dogging the door open. Plate measures 3" wide by 14-3/16" long, with an 1-5/8" bore for cylinder.
Von Duprin part # 880NL-R
880NL -
Von Duprin 99 Mechanism End Cap 050014
The Von Duprin 99 Mechanism End Cap 050014, also known as 33A/35A/98/99/330/350 Impact Resistant End Cap Kit. Replaces all of the old versions of the 98/99 End Caps, the mounting holes may be different. Includes end cap, bracket and all screws
Von Duprin Part # 050014
G99R10- -
Von Duprin 88 and 55 Cross Bar 967738
The Von Duprin 88 and 55 Cross Bar 967738 has been in use since the 1950's. The bar is 1" in diameter and is 42" long and can be cut down in the field. One side of the bar will be cut for the wedge tite screw opening.
Von Duprin Part # 050004
Old Part # 96773888R120- -
Von Duprin Thumb Piece 970488
The Von Duprin Thumb Piece 970488 is just the thumb piece only, rivet not included. Cast bronze construction, and then plated to the selected finish. 5-1/8" overall length, but note that the length is usually cut down in the field depending on the thickness of your door.
Von Duprin Part # 970488
Old Part # 960303G970488- -
Von Duprin Pull Handle 972466/972467
The Von Duprin Pull Handle 972466/972467 replacement Grip/Handle only, screws not included. Cast bronze construction, and then plated to the selected finish. The Grip measures 15/16" wide by 6" long. The center to center hole spacing is 5-1/2". This handle works on the Von Duprin 608, 696, 880, and 990 outside trim plates.
Von Duprin Part # 972466 and 972467
Old Part # 969925 and 959122G972466- -
Von Duprin 107765 Plunger Release Bracket
The Von Duprin 107765 Plunger Release Bracket is used with the Fire Rated 8827-F Top Latch. When the door closes, the Release Pin on the 88VR10-F (050462) hits the post and releases the latch from the retracted position. Once the top latch is released, it drops the bottom latch into the floor.
Von Duprin # 107765
G107765-