Von Duprin| Von Duprin Exit Devices
For the past 45 years Robert Brooke and Associates has been a leader in Von Duprin Exit Devices, either complete or repair hardware. Whether you have the economical 22 Series or the higher end 98/99 Series we have the hardware you need. Call and speak with product experts!
-
Von Duprin 88 End Case 050435
The Von Duprin 88 End Case 050435 is also known as the hinge case, meaning it is on the hinge side of the door. This End Cap is used on all of the Von Duprin 88 models, which include 88, 8827, 8847 and 8875. This piece does all the lifting of the cross bar, so it is an important component. The case includes the all of the internal workings and springs.
Von Dupin Part # 050435
88R20 -
Von Duprin 8827 Chassis Tie Rod Pkg 050328
Von Duprin 8827 Chassis Tie Rod Pkg 050328
The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.
Von Duprin Part # 050328
Old Von Duprin Part # 96761688VR195 -
Von Duprin 55 Rim Latch Bolt Spring 967502
The Von Duprin 55 Rim Latch Bolt Spring 967502 is only used on the 55 Rim Panic Hardware. This spring just keeps pressure on the latch bolt, it does not lift the arm. If your arm is sagging, they you need to tighten the crossbar wedge tite screws and check and make sure the 55R200 55 Hinge Case Spring is not broken. It measures 1-1/2" long by 3/8" diameter.
Von Duprin part # 050354
Old Part # 96750255R210 -
Von Duprin 55 Dog Screw-090053
The Von Duprin 55 Dog Screw-090053 is the newer version, meaning less then 25 years old. It measures 3/8" diameter by 1/2" long with 14 threads per inch. They did have an old style that was available up to a few years ago that had 15 threads per inch. If you have any old style I would recommend the D100 Panic Bar Retainer.
Von Duprin part # 090053
55R85 -
Von Duprin 55 Hinge Case Spring 090052
The Von Duprin 55 Hinge Case Spring 090052 is the spring in the inactive case. This spring does all of the lifting of the cross bar, and is used on the 55 Rim, 5547 Concealed Vertical Rod and 5575 Mortise Device. It measures 1-5/8" long by 5/8" diameter.
Von Duprin part # 090052
55R200 -
Von Duprin 2227/3327/9927 Bottom Latch 050401
Von Duprin 22, 33, 9927 Bottom latch.
Used to replace the bottom latch on the Von Duprin 2227, 3327A, and 9927 on devices shipped after October 1998.
Includes screws and sometimes the bracket
Von Duprin Part # 050401
G050401 -
Von Duprin 2227 Top Vertical Rod 109361
The Von Duprin 2227 Top Vertical Rod 109361 will work on all 2227's up to door heights of 7'1". The actual length of the rod is 37-3/8", less the fittings. If your door is taller you will need a rod extension. Call 1-800-642-2403 for longer top rods or rod extensions.
Von Duprin part # 109361
G22VR60- -
Von Duprin 2227 Top Latch 050091
The Von Duprin 2227 Top Latch 050091 latch is used on devices shipped before October 1998, see related products for the new style latch if your device is newer. This is usually the problem if your bottom rod is dragging on the floor. Latch measures: 1-1/16" wide x 4-5/16" long (less latch bolt) x 1-7/8" projection at the highest point. Includes screws.
Von Duprin Part # 050091
G22VR10 -
Von Duprin 2227 Rod Guides Assembly 112063
The Von Duprin 2227 Rod Guides Assembly 112063 works on all of the Von Duprin 2227's, and replaces the older style that featured the plastic cap and the springs. This device is used to add strength and rigidity to the top and bottom rods on there surface vertical rod.
Von Duprin part # 112063
G22VR80- -
Von Duprin 88 Center Case Rivet 090002
The Von Duprin 88 Center Case Rivet 090002 is also known as the Latch Tail Rivet used on the 88 Rim Device. The Rivet fits into the spring and into the Latch Tail 050500. The rivet measures 1-1/4 inches long less the head, with a 1/8 inch diameter. We sell this piece individually.
88r320 -
Von Duprin 050500 88 Latch Tail Kit
Von Duprin 050500 88 Latch Tail Kit
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
Von Duprin Part # 050500
G050500 -
Von Duprin 22 Mechanism End Cap 900981
The Von Duprin 22 Mechanism End Cap 900981 is the end cap and bracket that ships with the 22 and 2227 series. The bracket is constructed of zinc plated steel and the end cap is black plastic. Bracket also acts as mounting bracket that holds the exit device on the door. Von Duprin does offer a new Metal End Cap, look under related products.
Von Duprin part # 900981
G22R10 -
Von Duprin 22 End Cap Only 968601
The Von Duprin 22 End Cap Only 968601 is the end cap that goes on the hinge side of the door. When the cap breaks off the Dogging Cover Plate just slides off. Works on all of the Von Duprin 22 exit devices. If you need the bracket also, please order part # G22R10. Black plastic construction. As of October 1, 2014, Von Duprin no longer sells just the Plastic Cap Only. The complete End Cap and Bracket 900981 will be shipped in its place.
Von Duprin Part # 968601
G22R25
