Search results for: 'parts hold diagram yale 102 1600 door closer dogging'
-
Falcon Automatic Opener 8242
The Falcon Automatic Opener 8242 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8242 is a non handed, surface mounted, 115 volt closer for a push side mounting. If your door is an inswinging door you would use the 8231. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8242- -
Falcon Automatic Opener 8231
The Falcon Automatic Opener 8231 is a smart and easy solution to improve accessibility and meet ADA Codes. The 8231 is a non handed, surface mounted, 115 volt closer for a pull side mounting. If your door is an outswinging door you would use the 8242. This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.
This closer features:
SmartLatch-senses and overcomes external pressure conditions with a Graduated energy assist of secure latching.
Push N Go-selectable feature allows door to open automatically as soon as it feels pressure.
Open Position Learning-automatically sets the opening position to eliminate wall and door damage.
Obstacle Obstruction Detection-safety feature stops and reverses door direction when distress or an obstruction is sensed.
Pre-Load Strike Assist-removes load on strike lip with a one second delay allowing the door to release and automatically open.
LED Light Illumination-Light illumination on control box signals accurate installation and helps with connection diagnostics.
On Board Power Supply-powers the accessories without the need to install an external power supply-12 vac
Adjustable hold open time delay, backcheck/latch position, backcheck speed, and opening and closing speeds.The package includes everything except for the actuators. Uses LCN Actuators.
8231- -
LCN 1370 Quick Fix Plate
The LCN 1370 was a door closer made in the late 1990's to 2006 or so. The closer had a special mounting plate that made installation very quick. Many people have this door closer in use and now they are starting to fail. The LCN 1370-18QF Quick Fix Plate converts the mounting holes of the 1370 to a standard template closer, which is 3/4" x 9-1/16". By using this plate you will not have to redrill holes in your door. The plate measures 2 by 10-1/4 inches with tapped holes that measure 3/4 x 9-1/16 inch.
1260-18QF- -
Monarch 19 Series End Cap Bracket
Monarch 19 Series End Cap Bracket
This steel bracket holds the hinge side of the panic bar on the door. The end cap then fits over it for a finished look. Bracket measures 1-5/8" tall by 1-1/4" wide with a 15/16" projection. Sometimes shipped with a mounting barrel nuts and screw.
Monarch Falcon Part # 650320 or old part # 600108
G19R100B -
5" Kickdown Door Holder FS555
5" Kickdown Door Holder FS555
The H.B. Ives FS555 Kick Down Door Holder has been a staple in schools for many years due to its heavy duty construction and inexpensive price. It is constructed of durable cast iron, which has great strength characteristics. The shoe is made of a non-marring rubber, which is replaceable. The shoe is also held in place with a screw, which makes it a great option in schools and area of high vandalism. This holder will work on door to floor clearances of 3" or less. The hole spacing is 7/8" x 1-9/16".
Made by H.B. Ives
GJL555- -
International Door Closer 8630S SVR Device-Grade 1
International 8630S Surface Vertical Rod Device-Grade 1
DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.
Non handed, 4-1/2" minimum stile width. Smooth Surface.
For doors 29" to 36" wide order the Size 30 to 36"
For doors 36" to 48" wide order the Size 48"8630S- -
Sargent 20/30/60 End Cap Bracket
The Sargent 20/30/60 End Cap Bracket is used with the larger end cap. This end cap has been manufactured for the last 40 years and started its life on the obsolete 60 Series. The bracket holds the hinge side of the exit device on the door, and the G20300C fits over the top of it.
Sargent part #68-2141
G20300B -
Sargent 28-0109 Center Case Cam for 2828 / 2838
Sargent 2828 / 2838 Center Case Cam
The Sargent 2828 / 2838 Center Case Cam is the Cam that the key cylinder actuates to open the door. The Cam is located in the middle of the Center Case. We can no longer get the retaining ring to hold it in place.
Sargent Part # 28-0109
G280109 -
Magnetic Door Stop/Holder
Magnet Door Stop
Hands-free magnetic door stop/holder. All you need to do is open the door and a strong maget will keep it open until you close it. Mounts horizontally or vertically. Includes fasteners plus 1 concrete and 3 hollow wall anchors.
Not for use on doors with spring hinges or door closers.
GDS100 -
Jackson 1275 Panic Device SVR
This CRL Jackson® Exit Deviceblends the reliability of the time-proven 10 Series Crossbar Device with the sleek, contemporary style of today's modern push-pad exit device. Available in a Rim, Concealed, and Surface Vertical Rod versions, this device is suitable for use with 1-3/4" (44.5 mm) narrow, medium, and wide stile aluminum, wood, or hollow metal doors. The base is easily trimmed for field sizing, and the vertical rods are shipped to fit up to 84" (2.13 m) tall doors. Extensions or longer rods for taller doors are available. This Exit Device features an easy-to-use dogging system, and is also available with keyed cylinder dogging.
The 1200 Series touch pad with "Soft-Touch" insert requires slight pressure anywhere on the bar insert for instant release of the locking mechanism. Overall projection is only 2-7/8" (73 mm) from the door surface, and mounting hardware is concealed. Active outside trim and other panic accessories are available.
1275EO- -
Corbin Russwin 188F03 Quik-Install Mounting Bracket
The Corbin Russwin 188F03 Quik-Install Mounting Bracket is the standard bracket shipped by them for the past 40 years. This replacement bracket will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. This bracket is what you mount on the door or door frame and the door closer cylinder mounts to. Corbin Russwin part # 188F03.
Bracket size: 1-3/4" (44mm) (vertical) x 6" (152mm) (horizontal)
Hole spacing: 1" (25mm) (vertical) x 4-5/16" (110mm) (horizontal)G188F03 -
8" Kickdown Door Holder Grand Standard
8" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 7-3/8" to the Floor when mounted.
Made by Grand Specialties 608z
GJ608 -
Von Duprin Strike 299F
The Von Duprin Strike 299F is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299. Ships with shim and mounting screws.
Von Duprin Part # 299F
299F -
Pivot Set TH1116 Aldora Style
TH1116 Aldora Style Offset Pivots are used for both flush face frame installation and 1/8" recessed door applications. Pivots replace most major door manufactures. Suitable for aluminum doors weighing up to 125 pounds. These pivots are engineered and designed for durability, style and are easy to install. To order pivot: For LHRB door order RH pivot For RHRB door order LH pivot Specifications * 3/4" offset pivots for aluminum doors and frames * For flush door / frame and 1/8" recessed door applications * Weather resistant * Aluminum case construction * Vertical adjustment 1/8" * Full race ball bearing and design, provides smooth operation on bottom pivot door portion * No sag, entire weight of doors rests on floor mounted pivot portion * Completely temper proof, yet easily removable, replaceable in unlocked position * All pivots are handed- specify LH, RH * Finish: AL-Aluminum, DU-Duronotic
TH1116 -
Dor-o-matic 1790 NL/HB Cylinder Assembly 179CA
Dor-o-Matic 1790 NL/HB Cylinder Assembly. Converts a 1790EO to the Night Latch or Hold Back function
Doromatic Part # CYLASY.1151 or 179CA
GCA7 -
Dor-o-Matic 1690 Pinion Support Bracket PB312
Dor-o-Matic 1690 Pinion Support Bracket. Bracket holds pinion tip so that it will not slip
Doromatic part # BRKT.478, BRKT.133 or PB312
Dor-o-Matic 1690 Repair Parts Breakdown
GPB312 -
Von Duprin 22 Panic Only 22EO
The Von Duprin 22 Panic Only 22EO is part of the economy series. Even though is it the least expensive Von Duprin, it is still a very heavy duty panic device. It is for all types of single and double doors with mullion, for door stiles as narrow as 3-13/16”. All 22 Series exit devices are UL listed for Panic Hardware or Fire Hardware, and are certified to ANSI A156.3, Grade 1. The Von Duprin 22 ships with the 299 standard strike, dog key, and all of the needed mounting fasteners. Even though it is the least expensive, they offer all the replacement parts, just like there other models. We stock all of the replacement parts Von Duprin has to offer on the 22 and 2227 series.
We keep the 36” devices in stock in the SP28 Sprayed Aluminum and SP313 Sprayed Dark Brown in stock.
Von Duprin Part # 22EO22EO -
International Door Closer 8610S Rim Device-Grade 1
International 8610S Rim Device-Grade 1
DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.
Non handed, 4-1/2" minimum stile width. Smooth Surface.
8610S- -
Von Duprin 22 Mechanism End Cap 900981
The Von Duprin 22 Mechanism End Cap 900981 is the end cap and bracket that ships with the 22 and 2227 series. The bracket is constructed of zinc plated steel and the end cap is black plastic. Bracket also acts as mounting bracket that holds the exit device on the door. Von Duprin does offer a new Metal End Cap, look under related products.
Von Duprin part # 900981
G22R10 -
4" Kickdown Door Holder Grand Standard
4" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 3-3/8" to the Floor when mounted.
GJ604- -
5" Kickdown Door Holder Grand Standard
5" Kickdown Door Holder Grand Standard
Frequently we are asked, “What is the heaviest duty kick down holder you sell?” The answer to that question is any of Grand Specialty door holders. These door stops are American made and simply the best out there. They have a shoe that is held in place by a screw, a rivet instead of a roll pin for the hinging mechanism, and a “wedge” instead of a piece of spring steel to hold up the leg. They are constructed of steel, and not cast like all of the other door holders made.
Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.
- No roll pin at pivot point
- Mallable with a pair of pliers
- Rubber shoe held on by a screw
- American Made
- Zinc plated steel
The bottom mounting screws holes would be 4-3/8" to the Floor when mounted.
made by Grand Specialties 605z 605b
GJ605- -
Ives 7222INT Intermediate Pivot
• Use with 7212, 7212V or 7222 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.7222INT -
Wall Door Stop / Holder WS445
The Ives Wall Door Stop / Holder WS445 has been a staple of the Ives product line for at least the last 45 years, and is the same product as the WS443 except it has a holder function. The stop features cast brass construction and then plated the the desired finish, which makes it ideal for interior or exterior use. The rubber tip is a non marring rubber, that can be replaced and we keep in stock. The stop has a 2-1/4" base diameter and a 3-11-16" projection from the wall. This product ships with an expansion shield and lead shield. This holder is considered a manually holder due to the fact you have to bend over and latch and unlatch it.
GJW27- -
Corbin Russwin Regular Arm for 2800
The Corbin Russwin Regular Arm for 2800 is the standard arm shipped by them for the past 40 years. This replacement regular arm will work on the older Corbin 100, 110, and 120's, and the Russwin 2800, 2810 and 2820's. Along with the DC3210 and DC6210 Door Closers. The arm is non handed and can be used for regular, parallel and top jamb mount. Corbin Russwin part # 688F95.
2800RA -
Von Duprin NL Drive Screw 090074
Von Duprin NL Drive Screw 090074
The 090074 NL Drive Screw is used on the Von Duprin 22, 98 and 99 Exit Devices to control the rotation of the key cylinder cam. This small set screw, screws into the back of the chassis assembly next to the receptor for the Rim Key Cylinder. The set screw measures 5/16" long by 3/16" diameter. Note: When the NL drive screw is left in back of device, the outside cylinder will function only as a Night Latch. The Night Latch function means the door can only be opened, but not dogged open with the key cylinder.
Von Duprin Part # 090074
Old Von Duprin Part # 970441G090074 -
Sargent Parallel Arm Bracket 125-P
The Sargent Parallel Arm Bracket 125-P is for use with the 25-O regular arm, to convert it to a parallel arm mount. A parallel arm mount is when the door closer is mounted on the push side of the door and the arm is parallel to the door when in the closed position.
Sargent part # 125-P9
350PAB-